22 ms·
Why I Drilled Holes in My MacBook Pro and Put It in the Oven
- unvs 12y agoI have the same laptop model and I'm on my 4th logic board. Luckily, we have 5 years of warranty for hardware failures by law where I live.
- josephagoss 12y agoWhere do you live?
- unvs 12y agoNorway
- delsalk 12y agoIs that part of the EU wide protection places like the UK, Germany, etc also get or something specific to your country?
- mschuster91 12y agoEU mandates only two years, http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=CELEX:31999L0044:DE:HTML http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=CELEX:... Art. 5 (1)
- lafar6502 12y agoNorway is not EU member
- kozhevnikov 12y agoIt is member of EEA [1] though which means they "adopt almost all EU legislation related to the single market, except laws on agriculture and fisheries." [1] https://en.wikipedia.org/wiki/European_Economic_Area https://en.wikipedia.org/wiki/European_Economic_Area
- k-mcgrady 12y agoEU provides 6 years but not from the manufacturer - from the seller. I actually had a problem where Apple told me my manufacturer warranty was up and explained I still had 6 years from the seller (Vodafone) and to go to them. Vodafone pretended the law didn't exist. Eventually Apple were kind enough to replace the device even though they had no obligation to.
- delsalk 12y agoI wonder how that applies when you purchase something from an Apple Store, since that means they're both. I remember seeing a page on the Apple website listing info for extended warranties in EU member countries, which I assume this specific defect in the 2011 Macbooks is covered by.
- k-mcgrady 12y agoIf you purchase it from the Apple store they provide the 6 years (the genius told me this).
- merrua 12y agoVodafone and rubbish customer service sure tend to go together.
- k-mcgrady 12y agoI've been with almost all UK phone companies (I used to buy a new iPhone each year for dev reasons but run simultaneous 2 year contracts meaning I had to be with two phone companies at a time) and they are all terrible.
- icebraining 12y agoEU provides 6 years? How so?
- Alupis 12y ago6 years seems great an all as the consumer, but I'd imagine the retailers/manufacturers are not just taking this extra burden all on themselves, but likely passing it down the chain to the consumer via higher purchase price, higher contract price, decreased service quality, fewer staffers, or... etc... Needless to say, I sure wouldn't even want a smart phone from 6 years ago. People get upset at the USA's more-or-less forced upgrades every 2ish years, but that cadence does seem to fit the timing of when I start to feel my phone is not up to par... 2 or 3 newer generations of devices have come out since my purchase, my battery is starting to lose life (usually never covered by any warranty as this is a standard "wear-n-tear" item like car tires). I'd think a 2 or 3 year warranty should suffice in most cases.
- kozhevnikov 12y agoChecking the Apple legalese [1] [2] it seems that we can "choose" between Apple One Year Limited Warranty and consumer law [3] which happens to be 6 (England and Wales) or 5 (Scotland) years. Can anyone clarify that for me please? My screen is flickering on certain gradient backgrounds but my 1 year warranty was over before I noticed it. [1] https://www.apple.com/legal/warranty/ https://www.apple.com/legal/warranty/ [2] https://www.apple.com/legal/warranty/statutoryrights.html https://www.apple.com/legal/warranty/statutoryrights.html [3] https://www.apple.com/legal/warranty/products/uk-ireland-universal-warranty.html https://www.apple.com/legal/warranty/products/uk-ireland-uni...
- delsalk 12y agoReading your first two links makes it seem like you get both, given that your statutory rights aren't affected by Apple's own warranty, so for the coverage for the first or 3 years you can get anything solved via AppleCare, and for the remaining 2 or 3 you'd be making the claim to Apple (if you bought it via their stores or their website) as part of your statutory rights.
- nl 12y agoIn Australia a manufacturer's warranty cannot override your statutory rights. The warranty rights are useful if they are better than your statutory rights though. Apple has previously been in trouble for trying to avoid their statutory requirements here, eg http://www.smh.com.au/digital-life/digital-life-news/apple-forced-to-adopt-new-refund-policy-under-australian-consumer-law-20131218-2zkkr.html http://www.smh.com.au/digital-life/digital-life-news/apple-f...
- lobster_johnson 12y agoApple can't deny consumer law, so no. In countries like Norway (5 years "right of complaint" for electronics where the manufacturer is obligated to either repair or provide an equivalent product, new or refurbished), Apple has to oblige the consumer, by law.
- Hengjie 12y agoCan I just send my MBP Late 2011 to you so that you can send it to Apple to be replaced? The #mbp2011 group should really just set up a bunch of people there so that we can send it to Apple Norway to be replaced since MBP's warranties are worldwide anyway.
- mrweasel 12y agoThat must annoy the hell out of phone manufacturers. Even the two years in the EU is pushing it for a large number of phones.
- GFK_of_xmaspast 12y agoMaybe they ought to make better phones.
- oneeyedpigeon 12y agoWell, as a consumer rather than a phone manufacturer, I certainly appreciate living in the EU. For a several-hundred-€ phone to not be expected to last two years is a pretty depressing position.
- sokoloff 12y agoIt also probably keeps you from being able to buy a €20 phone. There are trade-offs in nearly anything.
- madawan 12y agoWhat are you talking about? I can get a €20 Samsung in any place that still sells dumbphones. I got a €30 Nokia 5 years ago and it still works splendid.
- morganvachon 12y agoThis is what drives me insane about the state of modern electronic device quality. It seems the less you pay, the longer it lasts. This is completely the opposite of how it is with traditional goods like furniture, utensils, tools, and so on. Maybe it's over-engineering, maybe it's forced obsolescence, maybe it's something beyond my comprehension. But it stinks.
- MrJagil 12y agoWell, a more expensive phone has way more (hardware) features, and thus way more points of failure. Makes perfect sense to me, though I do understand your position. Snow Leopard has been praised as the best OS X release for focusing almost solely on bug fixing. I wish releases such as this were more common both in soft- and in hardware.
- vacri 12y agoIn Australia, there is a minimum 1-year warranty, which is extended 'a reasonable amount' if the product is sold as a quality item (ie: 'put your money where your mouth is'). It was funny watching Apple a while back market its products to consumers as a quality item, but tell the government that it was 'just another computer', because they didn't want to honour their warranties past 1 year.
- gnarbarian 12y agoThis is what happens when function plays second fiddle to form.
- techrat 12y agoYou'd think after 10 years having model after model of aluminium built laptops, Apple would have found a way to solve the heat issues they always have... but nope, they still think it's a good idea to put the heat exhaust vent right up against the bottom lip of the screen where it is still blocked when the machine is in use.
- chroma 12y agoWhere else can one put air vents on a laptop? The sides are taken up by expansion ports and speakers. The front is blocked by the battery. The bottom is often obstructed by blankets, clothing, etc. The top is for the keyboard, trackpad, and palm rest. Putting vents at the hinge actually makes the most sense. It guarantees ventilation ports won't be fully obstructed. The vents face away from the user, reducing fan noise. Air ducts are short, since that area is close to the CPU/GPU. It's hard to cool a laptop that can generate 85 watts of heat. Moreso if one cares about it looking nice and being thin. You may not like the trade-offs Apple chooses, but they put a lot of thought into their industrial design.
- marcosdumay 12y agoMost laptops have the batteries on the back, making the front available for connectors. Most laptops have ventilation on a side, and some complement it with bottom holes. Also, Apple could place their CPU/GPU wherever they wanted.
- gnarbarian 12y agoMy Latitude E5430 has them on the left side near the back, and two places on the bottom (the rear left side and the front middle).
- 12y ago
- aceperry 12y agoThe author shows a lot of love for his laptop.
- lafar6502 12y agoObviously. But some less popular laptop vendors have this 'next business day' warranty where they send a technician to fix your laptop in your office or at home. Much better idea than a baking owen imho, however there is something in a scent of freshly baked mainboard ;)
- madeofpalk 12y agoFun fact: Apple also provides 'next business day' warranty with their consumer AppleCare warranty! But it sounds like his warranty has expired, hence the oven.
- uptown 12y agoMy early 2011 MBP has had one logic board replaced so far at my own expense a short while after AppleCare expired. This site has been compiling relevant information to those experiencing the same problem, and the #mbp2011 hashtag on Twitter is also a good resource for those affected: http://mbp2011.org/ http://mbp2011.org/ https://twitter.com/search?q=%23mbp2011 https://twitter.com/search?q=%23mbp2011
- jerrytsai 12y agoYes, this problem is widespread and unacknowledged by Apple. https://www.change.org/p/timothy-d-cook-replace-or-fix-all-2011-macbook-pro-with-graphics-failure https://www.change.org/p/timothy-d-cook-replace-or-fix-all-2... It's ludicrous that to attempt to fix this problem, you would have to go so far as to bake your laptop. It cost me over $US 500 to get this fixed at an Apple Store.
- some1else 12y agoHad two 2007 MacBook Pro's break down that way. Local Apple Care Service providers didn't want to apply Apple-mandated extended warranty. I was pretty disappointed to find out that later models exhibited similar flaws, because the soldering issue of 2007 models was blamed on nVidia. When a friend was buying her mother a christmas present iPad, I went with her to examine which models handle the tablet workload better. We ended up picking an older generation, non-retina model. A few previous generation retina models, presumably running latest iOS updates, had ridiculously high temperatures just idling on the shelf.
- Zak 12y agoNvidia made a run of defective GPUs somewhere around 2007-2008. Tom's Hardware claims[0] that all G84 and G86 GPUs other than warranty replacements produced in late 20008 are defective. It's not a BGA solder issue like we've seen on numerous laptop GPUs over the years, but a problem with the internal interconnects. Heating it, as if to reflow a BGA does temporarily solve the problem, but in my experience, the period of time it keeps working after heating gets shorter each time. [0] http://www.tomshardware.com/news/nvidia-g84-g86-chips-overheating,6121.html http://www.tomshardware.com/news/nvidia-g84-g86-chips-overhe...
- petercooper 12y agoOne time I saw it climb as high as 102º C—hot enough to boil water. If doing anything slightly intensive, my 15" MBPR is the same; I've had it hover at 100-105C for periods. Why not scale down the CPU at crazy temperatures? Intel CPUs have a cutout, but the entire machine needs a more gradual solution. Running at 90C+ is not viable long term. Now it's over 2 years old, I might just buy a entry level MBP instead rather than maxing out as I usually do. They seem fast enough now and what's the point if I can't even use the full power?
- Kurtz79 12y agoSame here. I bought the version with dedicated graphics for some light gaming, but the GPU throttles almost immediately, I doubt I'm getting better performance than I wold have with just Intel integrated graphics. I have reapplied thermal paste (which improved things a little bit), used a cooling laptop stand (useless), fiddled with smcfancontrol and other applications, to no avail. But I'm not drilling holes on the case, as someone said it would be hard to explain when reselling it :).
- petercooper 12y agoMy problem is more with the CPU than GPU. However, there's an app that lets you switch to using the integrated graphics only (which is fine for most situations, unless you plug in an external display) which is well worth trying.
- IgorPartola 12y agoNot to try to convince you to get something different, but FWIW there are more differences in the MBP and MBA lineup than just CPU and GPU. For me, the two major factors were RAM amount (couldn't get 16 GB's with anything but MBP 15" at the time), and ability to hook up multiple external displays. My current setup is the laptop screen + two external displays. At least as of a year ago MBA's and 13" MBP's could do this. At best, you could drive two external displays with a 13" MBP (but not its own screen). USB video cards are a solution, but consider that they drive CPU usage through the roof unless you are staring at a very static screen. I used to use one of these to display my terminal. Then one day I put the browser on this screen and was checking GMail when I heard my laptop basically lift off the desk from the heat and speed of the fans.
- joeblau 12y agoThis story is awesome. It would be hilarious if the OP ever tried to sell his laptop. I can imagine him trying to explain to a layperson why all of the drilled holes in the bottom are actually a benefit and not a problem.
- gnarbarian 12y agoThey're literally speed holes.
- veb 12y agoThey're really not. "Speed holes" by definition make something go faster. In this case, it was done to help the temperature. Not to overclock.
- gnarbarian 12y agoWithout them it doesn't run at all, so I still think they qualify.
- lttlrck 12y agoThey prevent it going slower.
- puckmunch 12y agoThey are neither red nor blue, disproving your statement.
- wingerlang 12y ago"They increase the airflow, making the computer never overheat and die" It's not that hard to understand.
- Morphling 12y ago"But they are ugly and now everyone is teasing me about them. I want a refund"
- gpvos 12y agoIs it normal in the US to use Celsius for computer inside temperatures, and Fahrenheit for the oven? Aren't you converting back and forth the whole time?
- rgawdzik 12y agoIt seems more like a Canadian convention to me.
- ars 12y agoYes, pretty normal. For temperatures near 100C the conversion is easy. Ovens report temperatures in F, computers in C, shrug. In general you use F for human temperatures (air temperature, fever, and cooking), and C for everything else. F has a better range for air and body temperature anyway. Maybe Europeans will switch to F, and Americans will switch to Km :) (In case you wonder why F is better: The coldest temperature normally experienced by people is 0F and the typical temperature is near 100F. Unlike C where you go negative, and the typical is 20.)
- pedalpete 12y agoI've always hoped we'd move to a 0-100 scale where the scale is the temperatures people can relate to. 0 is cold, 100 is hot. How hot is 100? Same as 100 farenheit. We know that's hot. How cold is cold? Same as 0 celsius, we know that's cold. Of course, for science and cooking we need more dynamic range, which F and C work well for, but just for our daily experience, we need something new.
- sjwright 12y ago> I've always hoped we'd move to a 0-100 scale where the scale is the temperatures people can relate to. That's exactly what Celsius is, except it pegs 0 and 100 at non-arbitrary temperatures that are both scientifically precise and exceptionally relevant to everyday use.
- emodendroket 12y ago
- Perdition 12y ago>I had a hunch that the problem was related to the thermal paste: When I disassembled it the first time, I had to scrape some thermal pads from under the Thunderbolt controller and the system hub. This left a large gap between the heat spreader and the chip. I’d tried to fill the gap with an extra big gob of thermal paste, but I suspected that the paste hadn’t gotten a good seal. Well yeah, that's a problem as thermal paste is only meant to fill in the microscopic irregularities of the contact surfaces and isn't some magical thermal bridge. Thermal paste has thermal properties on par with most condiments. Thermal pads are particularly bad. I would use a metal shim to bridge such a gap, not just more thermal paste.
- arsalanb 12y agoWell. If it adds to the value, the holes would also be a great conversation starter at conferences and hackathons.
- darkstar999 12y agoSuch as "why are you looking at the bottom of my laptop?"
- deleted 12y ago[deleted]
- proveanegative 12y agoI have question related to this issue. Which MacBook model, new, refurbished or used, should I buy if I want it to last as long as possible and be useful for doing OS X-specific programming tasks?
- stefantalpalaru 12y agoAs long as possible? Run OS X in a VM.
- kybernetyk 12y agoAny that fits in your budget. I've been running on MBPs since 2008 and never had one give up. (My oldest one still is running as a test device).
- shortstuffsushi 12y agoGirlfriend has a 2008 MB that I bought off Ebay, other than the hard drive dying (and giving me ample warning and time to replace first), it's had no problem. Since it's limited to 4GB RAM, it isn't really ideal for development, but she runs Photoshop and Illustrator on it (albeit, a bit slow for my taste). I personally own a late 2011 MBP (same as the article, I believe) with 8GB RAM, also no problems, running a pretty standard development set up. I have another 2012 MBP through work which is a bit beefed up, though still nothing fancy. Also no problems. Also manage a couple of 2010 Mac servers there which have been running steady since late 2010. Oh, and none of these have SSDs. So, say what you will about non-SSD, they work well enough for development. All in all, have to agree -- whatever fits your budget, at least in my personal experience, will work pretty well. I know that people do certainly have issues with them occasionally, but when I compare my luck with them to my luck with various other brands (Compaq, Dell, etc), they've lasted significantly longer with few or no problems.
- SyneRyder 12y agoIf that's a 2008 MacBook that you have, it should be able to (unofficially) take at least 6GB RAM. I have a 2007 MacBook with 6GB RAM and I've never had any problems with the RAM upgrade (running Lion & Mountain Lion, at least). Try looking up your model number in the small print here: http://eshop.macsales.com/shop/memory/MacBook/DDR2/ http://eshop.macsales.com/shop/memory/MacBook/DDR2/
- LeonM 12y agoI own the same laptop, I have it for about 2.5 years now and never experienced such temperatures. During a normal workday, (programming, compiling, git etc) I never once heard the fans spin up. I have a BookArc[1] laptop stand, which is about the worst possible way to keep a running MBP (lid closed, fan slots pointing down) and even with lots of gaming, I have never experienced any problems. Yes, I do clean the fans once a year, but all laptops need that. It goes to show that thermal wise the MBP is actually very well engineered. [1] https://www.twelvesouth.com/product/bookarc-for-macbook-pro-retina https://www.twelvesouth.com/product/bookarc-for-macbook-pro-...
- grandalf 12y agoI just use them on my lap and have never had heat problems with any of my macbooks. Before I bought my first macbook air I wrote a program on the console that slammed the CPU and left it running at the apple store. When I came back a few hours later the program was still running (100% CPU on all cores) and the machine was still cool to the touch. I then purchased the laptop.
- slantyyz 12y ago> I just use them on my lap and have never had heat problems with any of my macbooks. Yes, but have you ever specifically had a 2011 MBP like in the article? It's a very specific set of models that have the heat issue. Mine could easily hit 90C under load (it just bricked itself last week). Which mean it was quite hot to the touch. After I changed the thermal compound, it would hit the low 80s (C) at peak, but even then, it was quite hot.
- enigami 12y agoYou are kidding rite? I don't think you really did that to your MacBook, interesting story though
- marincounty 12y agoI had the same problem with a HP laptop a few years ago. HP denied their was a problem. Long story short; I will never give that company any more money. As to reballing a graphics chip, I would buy a kit off ebay, if made, and do it right. You are still taking a chance because you most likely don't have a proper heating station? I really like the additional holes. I would like to know exactly where my fans are and make a proper template. I would then use a very small gauge drill, and put in hundreds of holes. I would try to make it look like it came from Apple that way? I use "I would" too much. I probally won't likely do anything until mine goes dark? (I think the correct way of drilling holes is dismantling the MacBook Pro, which has always scared me.)
- spydum 12y agoi wonder why author choose to drill holes.. i'd think a cutting disk + slots would be better for airflow, and could be made to look a little better aesthetically
- jokoon 12y agoI have a mid 2009, 13" macbook pro, and when I use it in my bed, I make sure to put it on something that doesnt bend, like a slim large book with a hard cover, or a plastic tray. I don't really know why it gets hotter over the year. I guess fine dust end up clogging it, and since laptops are very slim, everything is packed, so it might be pretty hard to remove that dust. Some dust can stick to some surfaces, but I'm not sure. One thing for sure is that I wont use it for gaming or anything that might get it hot.
- dimitris99 12y agoWhat a fantastic way to deal with the problem. Whereas most people would have gone and paid money to some repair place, you took matters into your own hands. I love the iFixit approach to problems. (although I do understand why many people may find this a bit too much). What else can you hack?
- jfroma 12y agoI think the picture in the header says it all, on one side I can see very dirty fans and on the other side the improved design. The first thing I would have tried is to replace the fans. I had to do this with other laptops I have had in the past (HP mostly) but never with the two models of MBP (and I run pretty hard too), so I guess it has to do with the model as he mentioned. While I sympathise with the idea of improving the design of a product massively consumed, I first try to think that the engineers did a well design and try to look for the malfunctioning component to replace.
- deleted 12y ago[deleted]
- berkut 12y agoI've got an early 2011 MBP which has exactly the same issue - I'm on the third logic board (GPU and a chipset both went on separate occasions within 3-year warranty) and second battery (battery wasn't due to heat though, just capacity), I use it heavily for programming (compiling) and rendering, so CPUs are often maxed out. I try and make sure it's ventilated properly (when I use it on my lap I often hold it in the air when the CPUs are busy and the temp is rising), but I'm not convinced the design is good for cooling in general.
- hoffer 12y agoDo not replace the logic board a 4th time. Any Apple store manager is authorized to replace with a brand new 2014 model after three repairs especially for 2011 model owners. I just got my brand new replacement last month.
- digitalsushi 12y agoThere is an alternate universe where every time he took his computer apart, he skipped the reflow heat stuff and just put it back together... and it worked identically for identical periods of time between failures. I'm not saying it's this universe, I'm just saying there is one out there.
- Someone 12y agoI wondered that, too. I wonder whether he actually reflowed solder in the oven. Wikipedia gives a sample profile that heats to over 200 degrees Celsius for a minute or so. This uses around 170 degrees Celsius, which is used for preheating in the Wikipedia example. Also, a Google image search gives me reflow heats above 200 degrees for the 5 images I checked. Also "The speed holes worked: The boot chime rang. The screen glowed. The fans blew." doesn't make sense to me. The extra holes may help and may even fix his problem, but I find it hard to believe that successful booting shows that. Yes, it is a 'little' early for a final verdict.
- Alupis 12y agoWhy do you doubt the temperature did not reflow the board? When I solder electronics, I'm usually somewhere between 500F to 650F, but that's so things get hot enough quickly enough to not burn. I don't doubt a slow bake at 340F would do the same thing... some online googling shows people doing reflows with toaster ovens in the same temperature range (340F-450F). It's likely the solder joints were not completely disconnected, but rather simply cracked. So heating them a bit would allow the crack to reconnect, at least for a short while (seems to explain his symptoms of repeated failures after extreme system temperatures during operation).
- Justsignedup 12y agoIs it not true that baking it makes any "cracking" in the soldering smooth out since this is similar to what is done to boards at the factory during construction?
- jamesaguilar 12y ago
- jekrb 12y agoOff topic - The type looks so bad on this site using Chrome Beta on Ubuntu 13.10. Is there anything I can do to help render fonts better?
- DennisP 12y agoI'm running regular Chrome on 14.04 and it looks fine.
- giarc 12y agoI'm at work (XP, Chrome) and the font looks terrible as well. The thickness of the font changes within a single letter.
- LukaD 12y agoSame on Chromium dev channel on Linux. http://i.imgur.com/qFPBu1g.png http://i.imgur.com/qFPBu1g.png
- dzhiurgis 12y agoLooks like the real issue is lack of cleaning the dust once a year. Apple normally 'does not mind' if you open the case. Obviously you have to know what you are doing, hence the special screws. If you know what you are doing, you'll find where to spend $1 to get the correct screw driver.
- al2o3cr 12y ago"that’s how I saved my MacBook Pro with a drill and an oven." Alternate ending sentence: "So that's how I ruined my MBP with duct-tape-level thermal reengineering! Thermal resistance, wazzat?"
- dbg31415 12y agoGuessing the discussion at Apple was: Engineer: "We can get the computer to half heat if we add a few more intake holes..." ArtsySalesDouche: "Nein! Nein! Nein! I don't want that! I know nobody sees the bottom, but I don't want it, I don't want it, I don't want it, I don't want it!"
- skynetv2 12y agoi had to replace logic board on my mid 2010 mbp 15" after applecare expired. i also noticed my mbp also runs very hot even when i am not doing anything fancy. the most i have is 15 chrome tabs open. i know chrome is a hog but hey ... its a powerful system, should be able to handle it without heating my like an oven ready to bake chicken. compressed air many times .. no use i had to run smcfan but still its pretty hot.
- andrew_wc_brown 12y agoI owned an early Macbook Pro 2011 model. I had the logic board replaced 4 times and the 4th time paid out of pocket. After that one burnt out I gave up and bought a new computer. Simply the worst computer I ever owned.
- slantyyz 12y agoI only replaced my logic board once before it died, but I consider it the best -and- worst computer I ever owned. Outside of the fact that the board design was $*#$#387 and that it didn't have USB 3, it was a great computer in that it was fast, solid, light and easily upgraded. As prices came down, I kept upgrading the RAM and storage.
- puckmunch 12y agoFor what it's worth, Hewlett-Packard had a very similar problem with a line of theirs using the same GPU (and the same lead-free solder), and Microsoft's Red Ring of Death is fundamentally the same problem. The fact that you can only get a discrete GPU'd MBP now if you buy the most expensive model while the Iris Pro is capable of doing <i>everything</i> a discrete GPU did indicates that Apple's cut their losses with this technology. The motherboard's fine. The decision to accede to EU environmental mandates was the point of failure. No one in the industry sufficiently tested leadfree solder in GPU BGA mounts before going into production and to be fair, it was a year before people started noticing failures. Apple's dismal head-burying response only made it worse.
- smrtinsert 12y agoThis thread reaffirms my decision to stay on pcs. Substantially cheaper, and it encourages competition.
- mmastrac 12y agoExact same thing happened to me. I'd turn on an old 2009 era MBP and get a white screen, no chime and the whole thing would run really hot. Tried everything including firmware updates, PRAM resets and nothing would do it. Instead of putting it an oven, I turned it upside down, put a heating pad on it and placed the whole thing under a blanket for an hour. Turned on just fine after that.
- kendallpark 12y agoDon't try this at home, kids.
- packetized 12y agoThis problem/issue is nearly identical to the Red Ring of Death: overheating of a BGA-packaged Nvidia chip.
- pkolaczk 12y agoI have an old Dell Precision m4600 laptop. Big, bulky and heavy, but cooling is excellent, even though it has air intake on the bottom. Discrete Nvidia GPU running at full clock (because of an external UHD display) and temperature constantly about 60 degrees Celsius. And cleaning the fans/heatsinks is dead-easy and can be done in 10 minutes. Do newer MBPs have those overheating problems solved? I was thinking of buying one as my next laptop.
- deleted 12y ago[deleted]
- hoffer 12y agoI too had a late 2011 MB Pro with over-heating issues that led to 3 bad GPU's over three years (only paid for one of the repairs). Just last month I parked my ass in my local Apple store and told them I wasn't leaving without a brand new replacement. It did not take very long for the store manager to cave and I walked out with a brand new 2014 MB Pro. They won't formally acknowledge that their is an inherent issue with the 2011 models but I got the impression they just need you to make a big enough stink before they can replace.
- bluedino 12y agoIsn't it so much the GPU being defective and not the laptop overheating?
- gkop 12y agoI've said it before and I'll say it again: while the "giant aluminum heatsink" idea generally works pretty well for the MacBooks and has for some time, it's not the same as if Apple were to really fix the thermal engineering in their machines: The machines could run downright cool if only Apple were to steal some ideas from Lenovo and Asus. As a side benefit, Apple could begin referring to the machines as "laptops" again in their marketing from time to time (which they have abstained from for at least the last 5+ years).
- UnoriginalGuy 12y agoTo your second point, I doubt anyone will call anything a laptop ever again unless it runs at or below room temperature. There is a volume of evidence[0] that hot objects placed on the male genitals for an extended period of time can have a negative impact on fertility (and who knows what else, e.g. birth defects? Since it is likely damaging the semen). The liability issues are just too great. We're talking class action levels of expenditure. [0]http://www.webmd.com/infertility-and-reproduction/news/20041208/laptop-computers-may-affect-male-fertility http://www.webmd.com/infertility-and-reproduction/news/20041...
- jamesaguilar 12y ago> ever again I don't understand this claim. They are still calling hot devices laptops today. Do you mean that at some point in the future they will stop, and then they will never again call these devices laptops?
- matthewmacleod 12y agoI don't think Apple ever calls any of their machines 'laptops' – that's the point.
- ocb 12y agoThat's true, but I have a hard time believing it has anything to do with the fact that their laptops can get really hot. It's clearly marketing to differentiate themselves from their competitors.
- abakker 12y agoI have a 2011 MBP, but the 17 inch model. Have had zero problems with it, even though I use my computer for heavy amounts of RAW photo editing in Aperture, photoshop, etc. This problem may be relatively common, but I doubt it is universal. Of course, the people on this board are probably running generally more punishing tasks on their computers than the average, so if anyone was going to find this problem, it would be us.
- UnoriginalGuy 12y agoI don't know if RAW editing is the best example of heavy load. RAW editing in Lightroom and Photoshop (don't use Aperture) don't really test my machine at all unless I am "publishing" and that seems to be more IO bound than CPU/GPU bound (on an one year old i5). Gaming and BitTorrent (e.g. Battle.net launcher) are the only things that "upset" my machine heat/utilisation wise. Maybe full virus scans but that is more IO again.
- biot 12y agoShame that the holes are drilled so haphazardly. If only for the aesthetics, print out a template with the holes drawn on a circle, evenly spaced. Then use that as a guide to drill. Or find a local hacker group with a CNC drilling machine which will drill the holes with perfect alignment. Done right, it may have looked little different than a case with holes machined that way by the manufacturer.
- post_break 12y agoHe probably drilled them while filled with rage. Which is probably what I would have done. I was surprised the holes were so small. I would have just went over kill.
- dj-wonk 12y agoAgreed on the hole pattern. Laser drilling is an option too: https://www.ncms.org/wp-content/NCMS_files/CTMA/Symposium2005/presentations/Track%201/0330%20Vanderwert.pdf https://www.ncms.org/wp-content/NCMS_files/CTMA/Symposium200...
- vishal0123 12y agoHow in the world can heating a laptop repairs it.
- darkstar999 12y agoThe idea is that there is damaged solder connections, so heating the laptop melts the solder and fixes the connections.
- mattmcegg 12y agoI have nearly the exact issues with temps around 80-90 on my 2010 MBP while I produce in Ableton. I've done hours of research, and it sounded like a new Logic board was the only answer ($700). I even had both fans replaced about 2 years ago. Speed holes here I come!
- ortusdux 12y agoI always recommend looking into having laptops covered through your insurance company. I have state farm, and my wife and I have our laptops under personal article policies. The coverage is better, broader, and cheaper that anything else I've seen. My wife recently got a surface pro 3 to use during her forest soils PhD, and I was adamant we get nice insurance if she was going to be using it in the field. Two years of no deductible spill, drop, and malfunction coverage through squarespace is 280$. I get the same coverage plus theft and loss for 40 a year through my insurer. And it is a 3 block walk to the office where I can eat pastries and drink coffee while I file a claim. I have only had to file one claim, but it was for a head crash and they covered a new hard drive w/out question. I'm not saying it is a good fit for everyone, but it works out well for me. I do recommend squarespace for individual parts of a self-built tower pc. I spent 120 on a motherboard and on the third replacement spquarespace upgraded me because it turned out that model had an almost 50% failure rate in the first year.
- ics 12y agoSurely you mean SquareTrade, right?
- ortusdux 12y agoMan those squarespace ads on podcasts have done their job...
- Nitramp 12y agoDon't buy insurance for things that won't ruin you. The insurer will calculate the risk of whatever happening, and obviously charge more than likelihood * cost. So unless your risk is higher than average, you're losing money. And keep in mind that the average insurance taker probably has higher risk than the overall population.
- eli 12y agoEven if it won't ruin you, unexpectedly having to shell out over a thousand dollars for a new laptop might be so much of a hassle that it's worth "wasting" a few bucks each month to not have to worry about it.
- robertnealan 12y agoTo anyone who has had extensive issues with MBP's, I managed to get my 2007 replaced for free back in college with a new version by Apple after several unreasonable repairs (2x logic board, 3x LCD, 1x left IO board, 1x top case, 1x touchpad, 1x DVD drive). Granted, it took a lot of "let me speak to your manager" and I believe needs to still be under Applecare in most instances, but it's always an option to pursue if you have the time and patience. Thankfully the 2010 I received lasted until this year with no issues, and I finally replaced it after beating it to hell with a 2014 retina MBP that's been running smoothly so far.
- wyager 12y agoSame. After 7 or 8 repairs to the same machine, I managed to convince Apple to give me its purchase price in store credit.
- anigbrowl 12y agoI'm all for the repair ethic of iFixIt, but I wonder about the economy of this - besides the huge amount of time and uncertainty (that wouldn't be a good trade-off for anyone who isn't a professional repairer), I'd rather not know what sort of fumes rise off a circuit board when broiling it with a heat gun or taking it out of a hot oven. Also, at what point is he willing to acknowledge that maybe this thing is not all that well designed, especially going by how widespread this problem seems to be?
- slantyyz 12y ago>> Also, at what point is he willing to acknowledge that maybe this thing is not all that well designed, especially going by how widespread this problem seems to be? Perhaps the bigger question is at what point will Apple acknowledge that it is a real problem?
- ansible 12y agoI'd rather not know what sort of fumes rise off a circuit board when broiling it with a heat gun or taking it out of a hot oven. Shouldn't be much in the way of fumes. The circuit board goes through a similar process at manufacturing time. After that, the board is washed to remove excess flux and other gunk. Assuming the OP didn't leave any stickers or such on the circuit board, it should be fine. As a note to anyone thinking to do something like this... you should only try to reflow the board itself. Take everything apart. Do not, under any circumstances, heat up any kind of battery, or else bad things will happen.
- tonyjackson 12y agoI'll never understand those that insist on doing real work, or gaming, with a laptop. When dealing with a GPU, and especially one made by nvidia, you're battling with the laws of physics. Super hot things make other, nearby things, super hot. Even with proper cooling, nvidia chips overheat and die. Anyone that has had nvidia already knows this. They have a lifetime of a year or two, max. Get a desktop already. At least then, when your fancy GPU has a meltdown, you can salvage things from the wreckage.
- STRML 12y agoFor a lot of us, a desktop is just too big and too much work. A laptop is easy, it's everything right in front of you, it's fast enough, it's cheap enough, and it's portable. Aside from serious business use (trading, rendering, etc), gamers, programmers and data hoarders, there's not really a great reason for the average person to have a desktop anymore. Laptops that were built with thermals in mind actually do quite well at full load. I used to play a decent amount of games on my Lenovo Y500 when it was new and it could do full load for hours and hours without getting hot. It was still less noisy than my Macbook. The secret is to build a high diameter fan and a wide fan vent. Unfortunately Apple seems to think that being thin is more important. It's certainly easier to market.
- driverdan 12y agoThere are a lot of reasons why someone wouldn't buy a gaming desktop. 1. They just spent $2000+ on a laptop and don't want to / can't afford to spend another $1500+ (desktop + decent display). 2. They only game occasionally. 3. They don't want to own more stuff. 4. Their laptop has a warranty which covers any GPU issues. In my case all of these apply.
- tonyjackson 12y agoCongrats? You have everything you want, and no license to complain when your Macbook overheats and dies I guess. And you also seem to recognize that it will die. As long as you use the right tool for the right job, sure...
- azinman2 12y agoI wouldn't want to eat any food out of that oven....
- wldlyinaccurate 12y agoMost (all?) component manufacturers use lead-free solder these days. Lead alloy solders are harder to come by since they're generally only used by hobbyists who find them easier to work with.
- lostlogin 12y agoThe board would bother me more.
- azinman2 12y agoWell that and everything else too. There are any number of toxic chemicals/elements all across that board, from inside the ICs (does any of it vaporize out?) to the plastic PCBs, whatever is in the solder, etc etc. It's hardly meant to be 'food safe'.
- caycep 12y agoThis is one of the philosophical beefs I've developed against discrete GPU's, particularly in laptops. I've been using 13" unibodies with iGP's (Sandy, Ivy, Hassy vintages) and haven't had any of these problems. Bad stick of RAM, sure, but I blame samsung or whoever their supplier was. But most of the MBP deaths I've heard about from friends have been with AMD/nVidia GPU daughter cards on the 15's. My rMBP 13" also has side vents and vents under the screen which are very much unblocked and unobstructed. It might be also I don't game on laptops...I save that for a desktop with a GTX670 card and plenty of fans..
- forrestthewoods 12y agoWhy the beef against discrete GPUs? Shouldn't the complaint be against cases not properly designed to house them? MacBooks also use, quite frustratingly so, damn near the slowest Nvidia mobile GPU you can buy! A newer model might actually run faster and cooler.
- puckmunch 12y agoDiscrete GPUs are soldered to boards using ball-gate arrays, a technique which was invented with lead solder balls in mind. The patent holder died before the EU mandated non-lead solders. The reason this matters is because the process by which those solder balls are made does not check for the presence of voids in them. At least 10% of these balls (regardless of composition) x-ray as having voids. GPUs go through the most radical thermal shifts of any surface mounted component. Lead has a sense of humor about that kind of temperature change; tin alloys do not and begin to crack after a sustained number of shifts. This happened on my 2011 MBP which was not used for gaming. It's worth noting that the iMacs made the same year, where the discrete GPU was a replaceable daughtercard, had a voluntary recall for exactly the same reported video problems. The irony here is that the average cost of having a GPU reballed is about $150US, with a high rate of reliability compared to reflowing. Part of that reliability comes from reballers refusing to use anything but lead. The EU is directly responsible for this problem but Apple is responsible to its users and with a cash reserve outstripping the US Treasury's, could have absorbed the cost of repairing these MBPs easily.
- jimbobimbo 12y agoReminds me of my parents' Sony Trinitron TV. The thing is 20 years old. From time to time TV starts misbehaving, they call up some local guy, who refreshes soldering on TV's internal components and the TV just works after that. Twenty years old - still can't believe this!
- lostlogin 12y agoI bet it has a degause button too. I badly miss a good degaussing on a 32 inch+ monitor.
- rcthompson 12y agoI had a mini-ITX case where the AGP port (yes, it was a while ago) was right up against one of the walls, so the GPU fan was pinned against the wall. As expected, the machine crashed every time I started up a game. We fixed it by drilling holes in the wall right where the GPU fan faces it. The next version of the same case came with an array of holes drilled in that exact same spot, so I guess we were on to something.
- brendannee 12y agoI did a little holiday baking myself this year - fixing my old Samsung 30" display in a similar way: http://blog.bn.ee/2014/12/22/sometimes-you-just-need-to-bake-your-monitor/ http://blog.bn.ee/2014/12/22/sometimes-you-just-need-to-bake...
- dghughes 12y agoI wonder if it's worth the effort sure it may reflow solder if it's hot enough but the high temp lead-free solder or whatever Apple uses may require very high temperatures to get it to melt even a bit. I've changed enough capacitors on power supplies to know the damn things have solder that's practically indestructible, our old Pace solder station iron cranked to something like 850F and still I'm sitting there 5 or 10 minutes cursing it all the time, and nine more caps to go x two leads each. Plus that heat would degrade the life of components too so who knows if it's ever worth it. But I guess cheaper than spending thousands on a new Macbook Pro.
- sfeng 12y agoOften the issue is the component is sinking most of the heat away from the joint. If the giant chunk of metal your heating can dissipate the power of your soldering iron, you're not gonna heat much up.
- dghughes 12y agoTrue but even with the component removed and trying to clean up jagged solder on legs it's tough stuff to get to melt. This is the solder that comes from the factory we just use the lead-free regular stuff when it goes back in.
- dghughes 12y agoTrue but even with the component removed and trying to clean up jagged solder on legs it's tough stuff to get to melt. This is the solder that comes from the factory we just use the lead-free regular stuff when it goes back in.
- spost 12y agoJust a note to anyone here who may be having this problem: I had an early 2011 MBP, the GPU died three times in three months. Apple charged me $300 to fix it the first time, did it for free the second time because it was still under repair warranty, and then replaced the machine entirely with a brand new 15" MBPr the third time. Obviously, the fact that it failed three times in as many months is unacceptable (and probably uncommon) but if you're struggling with this, do set up a genius bar appointment and see if they can do anything for you.
- snowwrestler 12y agoI was sitting in an Apple store getting the battery replaced on my MacBook Air. It only lasted 300 cycles instead of the 1,000 it is supposed to. My battery replacement was free despite being outside the 1 year warranty. Next to me a woman had brought in her laptop because of problems (did not overhear what), and they replaced it for free despite it being 3 years old. I definitely agree that the first step with Apple stuff is to see what they'll do for you. Hitting the Apple store is the best way to do that, but they're not everywhere. I wonder if the mail-in folks have as much latitude to please the customer. (And of course if you mail it in, you're missing your computer for at least a week or two.)
- mgkimsal 12y agoIf you go to the store, you're missing it for days as well. I was told a repair would take 3-5 biz days after I dropped it off - drop off on Monday, Tuesday is first biz day, etc. So.. effectively up to 1 week no computer, out min $300, and no replacement in the meantime.
- PhantomGremlin 12y agoIt probably depends on where you go and what the problem is. I've had 1 day turnaround from my local Apple store on a repair. On another repair (replace failing SSD) they fixed it in a few hours. They also replaced an iPhone 5C screen in a few hours.
- 12y ago
- jqm 12y agoI did something similar years ago with an HP laptop (direction from internet of course). Instead of the oven, I used a heatgun and a stack of nickles on top of the GPU chip. I almost fell over in surprise when the laptop booted right up afterwords.
- meburns 12y agoI had almost the exact same issue with my 2009 17' MacBookPro and when it finally wouldn't boot up anymore I took it to the closest Apple store near me. They told me they could do an out of warranty fix of the damaged part (whatever it was, something on the logic board) and it would be around $300. I agreed and they sent it in to their warehouse to get fixed, a few days later I get a call telling me that the part that was needed was severely backordered and I could either wait or they would give me a refurbished 2013 15' MacBookPro with comparable specs to my old MBP plus AppleCare and a bunch of other nice things. Needless to say that was the best $300 I ever spent, had they not been able to do anything with it I suspect I would be trying more things like drilling holes in the case ;)
- coherentpony 12y agoTLDR: Oven to re-set the solder if any of the connections were temperamental. Holes for airflow.
- stephen_g 12y agoMy early-2011 MacBook Pro died a few weeks ago after almost four years of quite heavy use. It actually took hardly any convincing to get the people at the Apple store to replace it at their cost - I'm not sure if that's because of Australia's stronger consumer protection law or because they knew how common a problem it is. They must have applied the heat transfer compound better than before, because with SMCFanControl running a bit higher than normal I haven't seen it go above 65 degrees C much now (admittedly I haven't done much heavy lifting with it yet) and feels cooler to the touch up the top.
- Marcus10110 12y agoI really wish iFixit would do a formal root cause analysis every so often. As an electrical engineer running a small manufacturing operation, I'm always very interested in the failure rates and root causes that much higher volume products see. Lead free solder melts somewhere in the 200C-300C range. The solder we use melts at 230 degrees, and we reflow our PCBs in a Vapor Phase Soldering oven, which precisely limits the PCB temperature to 230C. Reflowing a PCB multiple times risks solder paste flux exhaustion, and also risks parts on the bottom side of the PCB falling off. Also, some parts are rated only for a very limited time at these temperatures, even when they are not running. Cooking these parts multiple times results in a dramatic reduction in lifespan. It wouldn't surprise me if Apple did an x-ray inspection of every BGA part on every device they produce. This isn't common practice in the manufacturing lines that I know about, but I know that it's done in some cases. This would help catch cracks or other defects that would result in a reduced lifespan of the device, as well as detect show stopper issues. There are a lot of other things that can fail on a PCB due to heat long before the solder will melt on a BGA pin. My guess that this was a mechanical failure inside the PCB. Either a through hole failure (such as a via disconnecting from a PCB trace, since the PCB is undoubtedly a very high layer count producing many fragile connections to long copper vias, which would expand vertically and in radius during temperature cycles) or an inner layer connection defect due to PCB or copper expansion. In either case, cycling the temperature by a large amount could temporarily fix the problem by creating a good enough connection for operation. The bottom line is higher operating temperature always hurts mean time between failure. This is well studied, and many manufacturers will include plots of the operating temperature vs MTBF. Even though the laptop is working now, all of the components have been exposed to additional extreme additional thermal stress. Everything in the laptop is now much closer to failure. I don't expect the laptop will last much longer. I'm not familiar with the guts of a MacBook Pro, but if there was a larger than normal gap between the chips and their heat sinks, then this would definitely explain the higher than normal system temperature. Even if the heat sink compound was able to bridge the gap with minimal air bubbles, it's still a pretty poor thermal conductor. This may have been a manufacturing defect that Apple could check for in the future. (Although I would hope they already run the devices for some length of time in their final enclosures while monitoring component temperatures)
- zekkius 12y agoThis guy works for iFixit and is unaware that using a large amount of thermal paste is a terrible idea? Large amounts make heat transfer worse, not better. I guess you can't expect too much from a site that hawks its tools/repair over accurate reporting...
- ah- 12y agoOn a related note, I've been looking at GPU switching on Macbooks, mostly to get it working better on Linux. This work might also be useful to keep 2011 MBPs with a damaged dedicated GPU working with just the Intel card. If you have a 2011 MBP and are willing to spend some time developing a software workaround that at least lets you use it with Intel only, check out https://github.com/ah-/gmux-scripts/issues/1#issuecomment-68378770 https://github.com/ah-/gmux-scripts/issues/1#issuecomment-68... and https://github.com/codykrieger/gfxCardStatus/issues/150 https://github.com/codykrieger/gfxCardStatus/issues/150
- soheil 12y agoAmong the many things that can go wrong on a circuit with millions of components I never knew soldering would be a recurring one.
- fluffyhip 12y agoI used to work for an import/export packaging place and the owner was a really into high-end electronics. He showed me a trick where you place a waste damaged device into a sealed bag with molecular sieve (kinda like silica but way better) and 24-48 hours later is dry inside and out. I do regular (every 6 months or so) drying maintenance on all my daily use electronics (phone, laptop, etc.) Plus I've fixed many friends phones and laptops using molecular sieve and a mylar zip seal bag. Putting electronics in the oven is risky biz. Rice sometimes works but actually can do more harm than good. Best alternative... through it in the vegetable crisper in your refrigerator. It usually is the least humid place, best for drying.
- mattmaroon 12y agoApple: it just works.
- mattmaroon 12y agoApple: it just works.
- rebootthesystem 12y agoI apologize in advance for having to be harsh in my commentary. As someone with over 30 years in electronics manufacturing the first thought I had when reading this article was: This is an incredibly stupid idea. Do not try to play manufacturing engineer with your kitchen oven. You will, without a doubt, cause more harm than good. Not to mention coating the oven where you cook your food with stuff you don't want in your food. Modern high density RoHS electronics boards require higher temperatures in precisely timed and controlled vapor phase reflow ovens. Components, solder joints and the board itself will almost certainly suffer damage from uncontrolled non-vapor profiles in a kitchen oven. It is far more likely that components will be exposed to far greater temperatures than rated as well as all kinds of imaginable differential heating and thermal slew rates. You can destroy the vias and pads connecting multiple layers of a multi-layer PCB simply by having differential heating or high temperatures. You can also damage dielectrics in precise impedance controlled boards. You can cause problems with solder that might very much affect signal integrity in high speed signals (for example, around the memory subsystem). In general terms, you are very much opening Pandora's Box if you think you can use a kitchen oven to reflow a modern mid to high complexity circuit board. Beyond that, you don't have the necessary optical, x-ray and high-speed testing equipment required to verify operation. You don't even have access to design data needed to understand where critical paths might lie. Sorry. This is a really dumb idea. Then we move on to drilling holes for the fans. OK, great, yes, more cool air molecules per unit time is what cooling is about. However, this design does not have any air filtration mechanisms. So, by drilling a bunch of holes you are far more likely to create a situation where you will coat the entire inside of the computer with a layer of dust and dirt with the potential to cause major issues. If I had no choice but to cut holes on the bottom on one of these machines I'd take the time to engineer a bolt-on filter plate with washable filters so that the internals might be protected from contamination (within reason). A far better idea might be (more on that later) to engineer the attachment of a surface extension feature on the bottom of the machine rather than drilling ventilation holes. "Surface extension" is what you commonly see on heatsinks, in other words, fins. Anyone who's done thermal FEA quickly understands that designing thermal management by eye only works if you have a lot of experience. These machines probably have decent thermal design. Perhaps all that is needed to make them a bit better is to add 10 mm of metal to the bottom with a nice thick set of fins widely spaced in order to extend the surface and promote thermal exchange with ambient air. Final point on TIM's (Thermal Interface Materials) like thermal paste. Their main purpose in life is to take two non-perfect surfaces and bridge the little imperfections so that more molecules make a thermal connection between surface A and surface B. If you could polish both surfaces to absolute perfection and mate them to absolute perfection you would not need TIM's. When it comes to thermal paste, you want as little as possible and you do not want any air gaps. To some degree there's an art to applying these kinds of TIMs. The author talked about buying some copper sheet in an attempt to fix the problem. Again, horrible idea. You have have two layers of TIM, on one each side of the copper sheet. In the hands of those without the requisite knowledge or experience I feel that ceramic sheet-based TIMs are far safer (http://goo.gl/Q6e0Es http://goo.gl/Q6e0Es). But I digress. The best idea would have been to walk the machine to Apple and deal with it through their channel. That's what they do best. The good news is that this kitchen-reflow machine is unlikely to make it to the used market due to the drilling on the bottom. I would hope that the author will be honest enough to disclose the amateur reflowing of the main board if and when the machine is ever sold in the used market.
- lateguy 12y agoIrony, I am in apple repair center while writing this. I have a 9 month old macboook within span of 6 months the connector cable between hard disk and logic board got corrupted, I have no idea why this happened twice (even the apple customer rep. are also clueless) . As they don't have any warehouse in New Delhi(India), they order it from Bangalore(India) and take 5 days to replace it last time and same this time,. Anyone having idea why this hard disk cable corruption issue is happening again and again?
- lateguy 12y agoIrony, I am in apple repair center while writing this. I have a 9 month old macboook within span of 6 months the connector cable between hard disk and logic board got corrupted, I have no idea why this happened twice (even the apple customer rep. are also clueless) . As they don't have any warehouse in New Delhi(India), they order it from Bangalore(India) and take 5 days to replace it last time and same this time,. Anyone having idea why this hard disk cable corruption issue is happening again and again?
- dba7dba 12y agoI worry about heat in my apple computers. Heat/GPU issue killed my first 17" Apple Macbook Pro. Just as 3 year AppleCare ended. Heat seems to be the reason ethernet in my mac mini randomly dies every few days and the fix is rebooting the switch it's connected to. https://discussions.apple.com/thread/1341108?start=45&tstart=0 https://discussions.apple.com/thread/1341108?start=45&tstart... I believe a heat sensor either correctly or wrongly detects high heat and disconnects ethernet. It's never shutdown completely though. My last iMac screen was burned in just as 3 year warranty ended due to high cpu heat over the 3 years. The burn in happened right where the cpu was located. And current imac is even thinner, meaning less space for air to flow, which is why I'm forced to buy Mac Pro for my video editing. iMac would be more than enough for my need but I know the monitor will get burn in after 3 years and so i will just go for mac pro. At least it has good cooling system or so I hear. Well played apple. Well played.
- jdhawk 12y agoI'd like to see an aftermarket case bottom that doesn't look like shit. Water Cut a nice and usefull pattern & let me bolt it on to the bottom of my macbook.
- whitehat2k9 12y agoAnother reason to not buy Apple and get a proper PC laptop/desktop.
- hawleyal 12y agoYeah, other computer manufacturers have never had heat issues.
- joshontheweb 12y agoI once spilled an entire glass of water into the keyboard of my macbook while it was on. It automatically shut off. I thought I was hosed. I almost smashed it on the table in fury. Luckily I didn't. I quickly removed the battery, took the computer COMPLETELY apart, and blow dried it for a few hours. It came back on and has been working ever since like a charm. Its been over 5 years now. Same with an iPhone 5s. I dropped it into a glass of water. It didn't work for awhile but came around after a few days and worked fine afterwards.