6 ms·

Considering that you were seeing unpredictable behavior in the boot selector, with it randomly freezing, I would assume a hardware component (RAM?) kicked the b

by GranPC 9mo ago

Considering that you were seeing unpredictable behavior in the boot selector, with it randomly freezing, I would assume a hardware component (RAM?) kicked the bucket. If it were firmware corruption, it would consistently fail to present the menu, or wouldn't boot at all. Microsoft's code quality might not be at its peak right now, but blaming them for what's most likely a hardware fault isn't very productive IMO.

ankurdhama 9mo ago
So the "hardware failure" happening exactly at the same time the Windows update installation failed are not related? That sounds like a one in a billion kind of coincident.
- eli 9mo ago
  An upgrade process involves heavy CPU use, disk read/writes, and at least a few power cycles in short time period. Depending what OP was doing on it otherwise, it could've been the highest temperature the device had ever seen. It's not so crazy. My guess would've been SSD failure, which would make sense to seem to appear after lots of writes. In the olden days I used to cross my fingers when rebooting spinning disk servers with very long uptimes because it was known there was a chance they wouldn't come back up even though they were running fine.
  - SecretDreams 9mo ago
    > Depending what OP was doing on it otherwise, it could've been the highest temperature the device had ever seen. It's not so crazy. Kind of big doubt. This was probably not slamming the hardware.
    - refulgentis 9mo ago
      That was absolutely slamming the hardware. (source: worked on Android, and GPs comments re: this are 100% correct. I’d need a bit more, well anything, to even come around to the idea the opposite is even plausible. Best steelman is naïvete, like “aren’t updates are just a few mvs and a reboot?”)
  - zelon88 9mo ago
    This, 100%. I'd like to add my reasoning for a similar failure of an HP Proliant server I encountered. Sometimes hardware can fail during long uptime and not become a problem until the next reboot. Consider a piece of hardware with 100 features. During typical use, the hardware may only use 50 of those features. Imagine one of the unused features has failed. This would not cause a catastrophic failure during typical use, but on startup (which rarely occurs) that feature is necessary and the system will not boot without it. If it could, it could still perform it's task... because the damaged feature is not needed. But it can't get past the boot phase, where the feature is required. Tl;dr the system actually failed months ago and the user didn't notice because the missing feature was not needed again until the next reboot.
    - startupsfail 9mo ago
      Is there a good reason why upgrades need to stress-test the whole system? Can't they go slowly, throttling resource usage to background levels? They involve heavy CPU use, stress the whole system completely unnecessary, the system easily sees the highest temperature the device had ever seen during these stress tests. If during that strain something fails or gets corrupted, it's a system-level corruption... Incidentally, Linux kernel upgrades are not better. During DKMS updates the CPU load skyrockets and then a reboot is always sketchy. There's no guarantee that something would not go wrong, a secure boot issue after a kernel upgrade in particular could be a nightmare.
      - zelon88 9mo ago
        To answer your question; it helps to explain what the upgrade process entails. In the case of Linux DKMS updates: DKMS is re-compiling your installed kernel modules to match the new kernel. Sometimes a kernel update will also update the system compiler. In that instance it can be beneficial for performance or stability to have all your existing modules recompiled with the new version of the compiler. The new kernel comes with a new build environment, which DKMS uses to recompile existing kernel modules to ensure stability and consistency with that new kernel and build system. Also, kernel modules and drivers may have many code paths that should only be run on specific kernel versions. This is called 'conditional compilation' and it is a technique programmers use to develop cross platform software. Think of this as one set of source code files that generates wildly different binaries depending on the machine that compiled it. By recompiling the source code after the new kernel is installed, the resulting binary may be drastically different than the one compiled by the previous kernel. Source code compiled on a 10 year old kernel might contain different code paths and routines than the same source code that was compiled on the latest kernel. Compiling source code is incredibly taxing on the CPU and takes significantly longer when CPU usage is throttled. Compiling large modules on extremely slow systems could take hours. Managing hardware health and temperatures is mostly a hardware level decision controlled by firmware on the hardware itself. That is usually abstracted away from software developers who need to be able to be certain that the machine running their code is functional and stable enough to run it. This is why we have "minimum hardware requirements." Imagine if every piece of software contained code to monitor and manage CPU cooling. You would have software fighting each other over hardware priorities. You would have different systems for control, with some more effective and secure than others. Instead the hardware is designed to do this job intrinsically, and developers are free to focus on the output of their code on a healthy, stable system. If a particular system is not stable, that falls on the administrator of that system. By separating the responsibility between software, hardware, and implementation we have clear boundaries between who cares about what, and a cohesive operating environment.
  - GCUMstlyHarmls 9mo ago
    > In the olden days I used to cross my fingers when rebooting spinning disk servers with very long uptimes because it was known there was a chance they wouldn't come back up even though they were running fine. HA! Not just me then! I still have an uneasy feeling in my guts doing reboots, especially on AM5 where the initial memory timing can take 30s or so. I think most of my "huh, its broken now?" experiences as a youth were probably the actual install getting wonky though, rather than the few rare "it exploded" hardware failures after reboot, though that definitely happened.
  - jonathanlydall 9mo ago
    Not for a server, but many years ago my brother had his work desktop fail after he let it cold boot for the first time in a very long time. Normally he would leave his work machine turned on but locked when leaving the office. Office was having electrical work done and asked that all employees unplug their machines over the weekend just in case of a surge or something. On the Monday my brother plugged in machine and it wouldn’t turn on. Initially the IT guy remarked that my brother didn’t follow the instructions to unplug it. He later retracted the comment after it was determined the power supply capacitors had gone bad a while back, but the issue with them was not apparent until they had a chance to cool down.
- olyjohn 9mo ago
  I've fixed thousands of PCs and Macs over my career. Coincidences like this happen all the time. I mean, have you seen the frequency of updates these days? There are always some kind of updates happening. So the chances of your system breaking during an update is not actually that slim.
  - helf 9mo ago
    [dead]
- santoshalper 9mo ago
  Two bugs occurring at the same time is definitely not one in a billion, and with billions of computers in the world, weird shit is going to happen.
- nightfly 9mo ago
  windows update just doing a normal write causing the active chunk of flash memory being used to hold something in the boot loader to a different failed/failing section
- GranPC 9mo ago
  For all we know, this thing was on its last legs (these machines do run very hot!) and the update process might have been the final nail in the coffin. That doesn't mean Microsoft set out to kill OP's machine... Same thing could have happened if OP ran make -j8 -- we wouldn't blame GNU make.
- justsomehnguy 9mo ago
  "Hardware failure" => "WinUpdate failure" => "Corrupted system" conforms the Occam's razor.
- Graziano_M 9mo ago
  I had a friend's dad's computer's HDD fail while I was installing Linux on it to show him it. That was terrifying. I still remember the error, and I just left with it (and Windows) unable to boot. Later my friend told me that the drive was toast. Come to think of it, maybe it was me. I might have trashed the MBR? I remember the error, though, "Non system disk or disk error".
  - toast0 9mo ago
    IIRC, that error text comes from the mbr. You may have trashed the partition table?
    - Graziano_M 9mo ago
      Yeah, I think so. It's been ~25 years, and only while typing out that comment did I remember the error message and realize that's probably what I had done. If I recall correctly, he ended up scrapping the drive.
  - justinclift 9mo ago
    Yeah, sounds like the drive was still physically detected but that the expected boot loader wasn't present any more.
- croes 9mo ago
  Like winning the lottery? Happens quite often
- tobyjsullivan 9mo ago
  Over my 35 years of computer use, most hardware failures (very, very rare) happen during a reboot or power-on. And most of my reboots happen when installing updates. It actually seems like a very high probability in my limited experience. Of course, it’s possible that the windows update was a factor, when combined with other conditions.
  - fc417fc802 9mo ago
    There's also the case where the hardware has failed but the system is already up so it just keeps running. It's when you finally go to reboot that everything falls apart in a visible manner.
    - phire 9mo ago
      I also notice that people with lots of experience with computers will automatically reboot when they encounter minor issues (have you tried turning it off and on again?). When it then completely falls apart on reboot, they spend several hours trying to fix it and completely forget the "early warning signs" that motivated them to reboot in the first place. I've think the same applies to updates. I know the time I'm most likely to think about installing updates is when my computer is playing up.
      - ssl-3 9mo ago
        I try to do the opposite, and reboot only as a last resort. If I reboot it and it starts working again, then I haven't fixed it at all. Whatever the initial problem was is likely to still present after reboot -- and it will tend will pop up again later even if things temporarily seem to be working OK.
        fc417fc802 9mo ago
        How do you avoid sinking time into chasing illusory bugs?
        close04 9mo ago
- pdpi 9mo ago
  I think it's fair to say they're related, yes. But causality can well be the other way around — that Windows upgrade failed because of flaky hardware.
- taneq 9mo ago
  A software update can absolutely trigger or unmask a hardware bug. It’s not an either/or thing, it’s usually (if a hardware issue is actually present) both in tandem:
- wvenable 9mo ago
  If had happened any other time, there wouldn't be a blog post about it and we wouldn't be reading about it.
- deleted 9mo ago
  [deleted]
- ezfe 9mo ago
  This happens all the time, people always doubt it - but the patterns are always consistent: large updates kill hardware that's in progress of failing
- Aurornis 9mo ago
  > That sounds like a one in a billion kind of coincident Hardware is more likely to fail under load than at idle. Blaming the last thing that was happening before hardware failed isn't a good conclusion, especially when the failure mode manifests as random startup failures instead of a predictable stop at some software stage.
- wnevets 9mo ago
  This reminds me of the 3090 hardware problems being exposed by Amazons New World [1]. Everyone really wanted to blame the software. https://www.pcgamer.com/amazon-new-world-killing-rtx-3090-gpus/ https://www.pcgamer.com/amazon-new-world-killing-rtx-3090-gp...
- deleted 9mo ago
  [deleted]
Aurornis 9mo ago
Yeah, I agree. This just feels like an appeal to anti-Microsoft clicks From the article: > It won’t get past the Snapdragon boot logo before rebooting or powering off… again, seemingly at random. Random freezing at different points of the boot process suggests a hardware failure, not something broken in the software boot chain.
- colechristensen 9mo ago
  It could very well be something poorly configured in the boot chain leading to random failures. There are plenty of hardware things configured in software which can lead to plenty of different kinds of random failures.
- numpad0 9mo ago
  Or something hit max program-erase cycle counts and are returning corrupt/old data. Flash ROMs tend to become "sticky" with previous states as you write more to them. I think it's possible that ROMs used for early SoC boot firmware or peripherals firmware still don't have wear leveling that they could become unusable after just a hundred or so of writes.
- fortran77 9mo ago
  > This just feels like an appeal to anti-Microsoft clicks Exactly. Did you notice the one comment on his blog? It's a Linux zealot saying "Linux".
  - NewJazz 9mo ago
    How do you know they are a zealot?
  - Dylan16807 9mo ago
    You're trying to take too much from that single comment sample point.
  - bigyabai 9mo ago
    Deductive reasoning based on a sample size of one, HN comments are beyond the reach of parody.
deckar01 9mo ago
I would test the CPU cooler since the fans ran so hard. Temps ramp up around the login screen, then stay hot and reboots get unpredictable. I recently had a water cooler pump die during a Windows update. The pump was going out, but the unthrottled update getting stuck on a monster CPU finished it off.
inferiorhuman 9mo ago
With the original Arduino Due there was some fun undocumented behavior with the MCU (an Atmel Cortex-M3) where it would do random things at boot unless you installed a 10k resistor. From booting off of flash or ROM at random to clocks not coming up correctly. I swear I was doing just fine with it booting reliably until I decided to try flashing it over the SWD interface. But wouldn't you know it, soldering a resistor fixed it. Mostly.
shakna 9mo ago
The update listed in the article contains two UEFI patches, intended for "handheld devices". It would be entirely unsurprising to me if this trashed UEFI for this particular ARM device, from firmware corruption.
- tallanvor 9mo ago
  That's plausible, but I'd expect the UEFI patches to come from a vendor, not Microsoft. So if one came from Qualcomm, and they didn't properly specify the devices it should be installed on, that wouldn't make it Microsoft's fault.
p0w3n3d 9mo ago
when something works flawlessly and starts to fail after an update (so no user actions there) this could mean that update made the hardware fail. For example overuse of flash in ssd (it's been already reported https://community.spiceworks.com/t/anyone-else-have-their-ssd-bricked-by-microsoft-this-weekend-kb5063878/1237231 https://community.spiceworks.com/t/anyone-else-have-their-ss...) or reflashing a component too many times (simple error in scripts)
- MrGilbert 9mo ago
  Or it might not be related at all. Correlation and causality might be in charge here.
  - p0w3n3d 9mo ago
    Doesn't Ockham's Razor tell us to check the more obvious things first?
everforward 9mo ago
I'm not so sure, I've had a similar-ish issue on a W10 PC. I vaguely suspect a race condition on one of the drivers; I've specifically got my eye on the esp32 flashing drivers. Sometimes it boots fine, sometimes the spinning dial disappears and it gets hung on the black screen, sometimes it hangs during the spinning dial and freezes, and very occasionally blue screens with a DPC watchdog violation. Oddly, it can happen during Safe Mode boots as well. I would think hardware, but RAM has been replaced and all is well once it boots up. I can redline the CPU and GPU at the same time with no issues.
jasoneckert 9mo ago
Sage point. But it actually turned out to be non-hardware-related (I added an "Update: It's alive!" section to the blog post).

by GranPC 9mo ago

ankurdhama 9mo ago

So the "hardware failure" happening exactly at the same time the Windows update installation failed are not related? That sounds like a one in a billion kind of coincident.

eli 9mo ago
An upgrade process involves heavy CPU use, disk read/writes, and at least a few power cycles in short time period. Depending what OP was doing on it otherwise, it could've been the highest temperature the device had ever seen. It's not so crazy. My guess would've been SSD failure, which would make sense to seem to appear after lots of writes. In the olden days I used to cross my fingers when rebooting spinning disk servers with very long uptimes because it was known there was a chance they wouldn't come back up even though they were running fine.
- SecretDreams 9mo ago
  > Depending what OP was doing on it otherwise, it could've been the highest temperature the device had ever seen. It's not so crazy. Kind of big doubt. This was probably not slamming the hardware.
  - refulgentis 9mo ago
    That was absolutely slamming the hardware. (source: worked on Android, and GPs comments re: this are 100% correct. I’d need a bit more, well anything, to even come around to the idea the opposite is even plausible. Best steelman is naïvete, like “aren’t updates are just a few mvs and a reboot?”)
- zelon88 9mo ago
  This, 100%. I'd like to add my reasoning for a similar failure of an HP Proliant server I encountered. Sometimes hardware can fail during long uptime and not become a problem until the next reboot. Consider a piece of hardware with 100 features. During typical use, the hardware may only use 50 of those features. Imagine one of the unused features has failed. This would not cause a catastrophic failure during typical use, but on startup (which rarely occurs) that feature is necessary and the system will not boot without it. If it could, it could still perform it's task... because the damaged feature is not needed. But it can't get past the boot phase, where the feature is required. Tl;dr the system actually failed months ago and the user didn't notice because the missing feature was not needed again until the next reboot.
  - startupsfail 9mo ago
    Is there a good reason why upgrades need to stress-test the whole system? Can't they go slowly, throttling resource usage to background levels? They involve heavy CPU use, stress the whole system completely unnecessary, the system easily sees the highest temperature the device had ever seen during these stress tests. If during that strain something fails or gets corrupted, it's a system-level corruption... Incidentally, Linux kernel upgrades are not better. During DKMS updates the CPU load skyrockets and then a reboot is always sketchy. There's no guarantee that something would not go wrong, a secure boot issue after a kernel upgrade in particular could be a nightmare.
    - zelon88 9mo ago
      To answer your question; it helps to explain what the upgrade process entails. In the case of Linux DKMS updates: DKMS is re-compiling your installed kernel modules to match the new kernel. Sometimes a kernel update will also update the system compiler. In that instance it can be beneficial for performance or stability to have all your existing modules recompiled with the new version of the compiler. The new kernel comes with a new build environment, which DKMS uses to recompile existing kernel modules to ensure stability and consistency with that new kernel and build system. Also, kernel modules and drivers may have many code paths that should only be run on specific kernel versions. This is called 'conditional compilation' and it is a technique programmers use to develop cross platform software. Think of this as one set of source code files that generates wildly different binaries depending on the machine that compiled it. By recompiling the source code after the new kernel is installed, the resulting binary may be drastically different than the one compiled by the previous kernel. Source code compiled on a 10 year old kernel might contain different code paths and routines than the same source code that was compiled on the latest kernel. Compiling source code is incredibly taxing on the CPU and takes significantly longer when CPU usage is throttled. Compiling large modules on extremely slow systems could take hours. Managing hardware health and temperatures is mostly a hardware level decision controlled by firmware on the hardware itself. That is usually abstracted away from software developers who need to be able to be certain that the machine running their code is functional and stable enough to run it. This is why we have "minimum hardware requirements." Imagine if every piece of software contained code to monitor and manage CPU cooling. You would have software fighting each other over hardware priorities. You would have different systems for control, with some more effective and secure than others. Instead the hardware is designed to do this job intrinsically, and developers are free to focus on the output of their code on a healthy, stable system. If a particular system is not stable, that falls on the administrator of that system. By separating the responsibility between software, hardware, and implementation we have clear boundaries between who cares about what, and a cohesive operating environment.
- GCUMstlyHarmls 9mo ago
  > In the olden days I used to cross my fingers when rebooting spinning disk servers with very long uptimes because it was known there was a chance they wouldn't come back up even though they were running fine. HA! Not just me then! I still have an uneasy feeling in my guts doing reboots, especially on AM5 where the initial memory timing can take 30s or so. I think most of my "huh, its broken now?" experiences as a youth were probably the actual install getting wonky though, rather than the few rare "it exploded" hardware failures after reboot, though that definitely happened.
- jonathanlydall 9mo ago
  Not for a server, but many years ago my brother had his work desktop fail after he let it cold boot for the first time in a very long time. Normally he would leave his work machine turned on but locked when leaving the office. Office was having electrical work done and asked that all employees unplug their machines over the weekend just in case of a surge or something. On the Monday my brother plugged in machine and it wouldn’t turn on. Initially the IT guy remarked that my brother didn’t follow the instructions to unplug it. He later retracted the comment after it was determined the power supply capacitors had gone bad a while back, but the issue with them was not apparent until they had a chance to cool down.
olyjohn 9mo ago
I've fixed thousands of PCs and Macs over my career. Coincidences like this happen all the time. I mean, have you seen the frequency of updates these days? There are always some kind of updates happening. So the chances of your system breaking during an update is not actually that slim.
- helf 9mo ago
  [dead]
santoshalper 9mo ago
Two bugs occurring at the same time is definitely not one in a billion, and with billions of computers in the world, weird shit is going to happen.
nightfly 9mo ago
windows update just doing a normal write causing the active chunk of flash memory being used to hold something in the boot loader to a different failed/failing section
GranPC 9mo ago
For all we know, this thing was on its last legs (these machines do run very hot!) and the update process might have been the final nail in the coffin. That doesn't mean Microsoft set out to kill OP's machine... Same thing could have happened if OP ran make -j8 -- we wouldn't blame GNU make.
justsomehnguy 9mo ago
"Hardware failure" => "WinUpdate failure" => "Corrupted system" conforms the Occam's razor.
Graziano_M 9mo ago
I had a friend's dad's computer's HDD fail while I was installing Linux on it to show him it. That was terrifying. I still remember the error, and I just left with it (and Windows) unable to boot. Later my friend told me that the drive was toast. Come to think of it, maybe it was me. I might have trashed the MBR? I remember the error, though, "Non system disk or disk error".
- toast0 9mo ago
  IIRC, that error text comes from the mbr. You may have trashed the partition table?
  - Graziano_M 9mo ago
    Yeah, I think so. It's been ~25 years, and only while typing out that comment did I remember the error message and realize that's probably what I had done. If I recall correctly, he ended up scrapping the drive.
- justinclift 9mo ago
  Yeah, sounds like the drive was still physically detected but that the expected boot loader wasn't present any more.
croes 9mo ago
Like winning the lottery? Happens quite often
tobyjsullivan 9mo ago
Over my 35 years of computer use, most hardware failures (very, very rare) happen during a reboot or power-on. And most of my reboots happen when installing updates. It actually seems like a very high probability in my limited experience. Of course, it’s possible that the windows update was a factor, when combined with other conditions.
- fc417fc802 9mo ago
  There's also the case where the hardware has failed but the system is already up so it just keeps running. It's when you finally go to reboot that everything falls apart in a visible manner.
  - phire 9mo ago
    I also notice that people with lots of experience with computers will automatically reboot when they encounter minor issues (have you tried turning it off and on again?). When it then completely falls apart on reboot, they spend several hours trying to fix it and completely forget the "early warning signs" that motivated them to reboot in the first place. I've think the same applies to updates. I know the time I'm most likely to think about installing updates is when my computer is playing up.
    - ssl-3 9mo ago
      I try to do the opposite, and reboot only as a last resort. If I reboot it and it starts working again, then I haven't fixed it at all. Whatever the initial problem was is likely to still present after reboot -- and it will tend will pop up again later even if things temporarily seem to be working OK.
      - fc417fc802 9mo ago
        How do you avoid sinking time into chasing illusory bugs?
      - close04 9mo ago
pdpi 9mo ago
I think it's fair to say they're related, yes. But causality can well be the other way around — that Windows upgrade failed because of flaky hardware.
taneq 9mo ago
A software update can absolutely trigger or unmask a hardware bug. It’s not an either/or thing, it’s usually (if a hardware issue is actually present) both in tandem:
wvenable 9mo ago
If had happened any other time, there wouldn't be a blog post about it and we wouldn't be reading about it.
deleted 9mo ago
[deleted]
ezfe 9mo ago
This happens all the time, people always doubt it - but the patterns are always consistent: large updates kill hardware that's in progress of failing
Aurornis 9mo ago
> That sounds like a one in a billion kind of coincident Hardware is more likely to fail under load than at idle. Blaming the last thing that was happening before hardware failed isn't a good conclusion, especially when the failure mode manifests as random startup failures instead of a predictable stop at some software stage.
wnevets 9mo ago
This reminds me of the 3090 hardware problems being exposed by Amazons New World [1]. Everyone really wanted to blame the software. https://www.pcgamer.com/amazon-new-world-killing-rtx-3090-gpus/ https://www.pcgamer.com/amazon-new-world-killing-rtx-3090-gp...
deleted 9mo ago
[deleted]

Aurornis 9mo ago

Yeah, I agree. This just feels like an appeal to anti-Microsoft clicks From the article: > It won’t get past the Snapdragon boot logo before rebooting or powering off… again, seemingly at random. Random freezing at different points of the boot process suggests a hardware failure, not something broken in the software boot chain.

colechristensen 9mo ago
It could very well be something poorly configured in the boot chain leading to random failures. There are plenty of hardware things configured in software which can lead to plenty of different kinds of random failures.
numpad0 9mo ago
Or something hit max program-erase cycle counts and are returning corrupt/old data. Flash ROMs tend to become "sticky" with previous states as you write more to them. I think it's possible that ROMs used for early SoC boot firmware or peripherals firmware still don't have wear leveling that they could become unusable after just a hundred or so of writes.
fortran77 9mo ago
> This just feels like an appeal to anti-Microsoft clicks Exactly. Did you notice the one comment on his blog? It's a Linux zealot saying "Linux".
- NewJazz 9mo ago
  How do you know they are a zealot?
- Dylan16807 9mo ago
  You're trying to take too much from that single comment sample point.
- bigyabai 9mo ago
  Deductive reasoning based on a sample size of one, HN comments are beyond the reach of parody.

deckar01 9mo ago

I would test the CPU cooler since the fans ran so hard. Temps ramp up around the login screen, then stay hot and reboots get unpredictable. I recently had a water cooler pump die during a Windows update. The pump was going out, but the unthrottled update getting stuck on a monster CPU finished it off.

inferiorhuman 9mo ago

With the original Arduino Due there was some fun undocumented behavior with the MCU (an Atmel Cortex-M3) where it would do random things at boot unless you installed a 10k resistor. From booting off of flash or ROM at random to clocks not coming up correctly. I swear I was doing just fine with it booting reliably until I decided to try flashing it over the SWD interface. But wouldn't you know it, soldering a resistor fixed it. Mostly.

shakna 9mo ago

The update listed in the article contains two UEFI patches, intended for "handheld devices". It would be entirely unsurprising to me if this trashed UEFI for this particular ARM device, from firmware corruption.

tallanvor 9mo ago
That's plausible, but I'd expect the UEFI patches to come from a vendor, not Microsoft. So if one came from Qualcomm, and they didn't properly specify the devices it should be installed on, that wouldn't make it Microsoft's fault.

p0w3n3d 9mo ago

when something works flawlessly and starts to fail after an update (so no user actions there) this could mean that update made the hardware fail. For example overuse of flash in ssd (it's been already reported https://community.spiceworks.com/t/anyone-else-have-their-ssd-bricked-by-microsoft-this-weekend-kb5063878/1237231 https://community.spiceworks.com/t/anyone-else-have-their-ss...) or reflashing a component too many times (simple error in scripts)

MrGilbert 9mo ago
Or it might not be related at all. Correlation and causality might be in charge here.
- p0w3n3d 9mo ago
  Doesn't Ockham's Razor tell us to check the more obvious things first?

everforward 9mo ago

I'm not so sure, I've had a similar-ish issue on a W10 PC. I vaguely suspect a race condition on one of the drivers; I've specifically got my eye on the esp32 flashing drivers. Sometimes it boots fine, sometimes the spinning dial disappears and it gets hung on the black screen, sometimes it hangs during the spinning dial and freezes, and very occasionally blue screens with a DPC watchdog violation. Oddly, it can happen during Safe Mode boots as well. I would think hardware, but RAM has been replaced and all is well once it boots up. I can redline the CPU and GPU at the same time with no issues.

jasoneckert 9mo ago

Sage point. But it actually turned out to be non-hardware-related (I added an "Update: It's alive!" section to the blog post).