7 ms·
This article doesn't explain one interesting bit: It is important that these crushed stones stay clean. If dirt gets in them, known as fouling, filling the
by londons_explore 3y ago
This article doesn't explain one interesting bit:
It is important that these crushed stones stay clean. If dirt gets in them, known as fouling, filling the gaps between the stones, then eventually it will cause a derailment.
Briefly, the stones move slightly as each train passes above them. The tracks 'float' on the denser stone. This effect helps keep the track straight and level - higher regions get pushed down, while lower regions raise themselves up.
Fouling stops this effect, and eventually the track will become so uneven that a derailment happens.
To prevent this, a big part of railway maintenance involves digging out all the stones, washing them to get rid of sand and soil, and putting them back. Usually done every 25 years or so.
- dheera 3y agoStupid question from a software person: Why don't they just pour cement, epoxy, or tar over all the stones to fix them in place, fill in the gaps, and prevent dirt from getting in them?
- tedunangst 3y agoHow does the water drain through them?
- dheera 3y agoAgain here's my software mind: (a) If you fill all the gaps, water can't get in in the first place, and it doesn't need to drain. Abstract out the problem. (b) If water can still get in, it can also get out.
- grishka 3y agoExcept sometimes water falls out of the sky and it needs to drain somewhere.
- dermesser 3y agoThe rocks also need to be able to move a bit for elasticity, and have sharp edges. For that you also replace a part of the ballast every few years. That's hard to do when everything is sealed. Even with such "glue", the lifetime couldn't be eternal, after all.
- micromacrofoot 3y agowater snow and ice will readily destroy anything solid, better to drain it away - this is partially why roads need constant repaving
- panick21_ 3y agoThree is this thing called slab track, and that's essentially what you are talking about, just without any stones. https://grn.ams3.digitaloceanspaces.com/wp-content/uploads/DSC00856-1024x768.jpg https://grn.ams3.digitaloceanspaces.com/wp-content/uploads/D... Truly almost all new lines should be built this way, its simply a far, far better method. Slightly higher capital cost but far less maintenance.
- noja 3y ago> To prevent this, a big part of railway maintenance involves digging out all the stones, washing them to get rid of sand and soil, and putting them back. Usually done every 25 years or so. Is this that? https://www.youtube.com/watch?v=WqLynLWLd8Y https://www.youtube.com/watch?v=WqLynLWLd8Y
- dotancohen 3y agoI think that the title suggests that is repositioning the stones (ballast). This video seems to be of the cleaning process: https://m.youtube.com/watch?v=XWjUZJtR610 https://m.youtube.com/watch?v=XWjUZJtR610 I could be wrong, I had never heard of this fascinating maintenance until this very moment.
- codethief 3y agoI know nothing about this topic at all but, having browsed Wikipedia for a bit, the machine from the video looks very much like a tamping machine https://en.m.wikipedia.org/wiki/Tamping_machine https://en.m.wikipedia.org/wiki/Tamping_machine (The video title also says "tamper")
- olejorgenb 3y agoIn the comments they say that "tampering"[1] is done once every year and the wiki page does not mention cleaning as an objective. Tamping is done to readjust the ballast making the track more more level and durable. (One can infer it does some cleaning as well - getting rid of the topmost dust layer) https://www.youtube.com/watch?v=zNFUgTJR6jw https://www.youtube.com/watch?v=zNFUgTJR6jw seems to be the full cleaning procedure [1] https://en.wikipedia.org/wiki/Tamping_machine https://en.wikipedia.org/wiki/Tamping_machine
- weinzierl 3y agoThat was more insightful than the whole article. Another thing I was curious about but not answered from the article is if there are any alternatives.
- A321321 3y agoYes, there is. High speed rail quite often uses ballastless track [0] [0] https://en.m.wikipedia.org/wiki/Ballastless_track https://en.m.wikipedia.org/wiki/Ballastless_track
- fsckboy 3y agoTL;DR "ballastless track" is track rigidly set in concrete instead of the aforementioned floating, but it must be done to very tight tolerances and is expensive
- weinzierl 3y agoIf the tracks are rigidly set in concrete, how do they deal with thermal expansion then? Roads made from concrete usually have gaps every couple of meters, but you can't have that many gaps in railroad tracks I suppose.
- bombcar 3y agoEither way they buckle: https://www.networkrail.co.uk/stories/why-rails-buckle-in-britain/ https://www.networkrail.co.uk/stories/why-rails-buckle-in-br... https://www.youtube.com/watch?v=_LoXgN1QWZM https://www.youtube.com/watch?v=_LoXgN1QWZM https://www.youtube.com/watch?v=dqq0543JWzI https://www.youtube.com/watch?v=dqq0543JWzI (wiggle wiggle)
- michaelt 3y agoFirst of all, in the images shown in that article the rail clips are rigidly set in concrete, and the rails are clipped in place. With enough force they can slide longitudinally in the clips. Second, in most modern rail installations the track is pre-tensioned to deal with thermal expansion. The track is stretched with a hydraulic tool and welded while under tension, so thermal expansion just means reduced tension. This is why trains on modern rail lines don't make the familiar click-clack sound. (How much tension is applied depends on the country and weather - you can choose between tolerating high temperatures and tolerating low temperatures. This is why in the UK, there are sometimes train stoppages in very hot weather)
- throw0101b 3y ago> To prevent this, a big part of railway maintenance involves digging out all the stones, washing them to get rid of sand and soil, and putting them back. This is called "ballast cleaning" if anyone wants to do a search: * https://www.youtube.com/watch?v=zNFUgTJR6jw https://www.youtube.com/watch?v=zNFUgTJR6jw * https://en.wikipedia.org/wiki/Ballast_cleaner https://en.wikipedia.org/wiki/Ballast_cleaner
- noveltyaccount 3y agoCool video. That machine is incredible.
- myself248 3y agoWild. The workers seem to be wearing the amount of PPE that I'd want if I was just walking along downwind, but nowhere near the amount I'd want if I was working in the thick of things 8 hours a day. I wonder what their lung disease rates are like.
- cratermoon 3y agoThe ones I see are wearing N-95 masks or equivalent. I'm no expert, but based on what I've learned since early 2020 I'd say that's plenty, provided they only use them for one day and toss them out.
- MarkusWandel 3y agoSteam locomotives, at least, used total loss lubrication. Their brakes were made of asbestos. And a good preservative for railroad ties was creosote. Never mind the stuff they spray to keep vegetation at bay. So even I would probably be wanting to wear an N95 mask if exposed to dust from that stuff all day.
- Gare 3y ago> And a good preservative for railroad ties was creosote. Still is. There is even an EU exception to the ban because no replacement was good enough.
- kqr 3y agoHow the heck did we figure this stuff out? Honest question.
- viewtransform 3y agoApparently, trains do not derail that easily. Army Experiments In Train Derailment (1944) https://youtu.be/agznZBiK_Bs?t=15 https://youtu.be/agznZBiK_Bs?t=15
- Zardoz84 3y agoThere was a famous train accident in England thanks to dirty ballast stones, bad drainage, and rainy day.
- abrookewood 3y agoThank you! I saw one of these yesterday and I couldn't work out why it was such a large machine given that the only thing it seemed to be doing was moving ballast slightly away from the tracks.