7 ms·
I am disappointed that many phones/tablets don't go very dim. From flagship to cheap, it seems that if you're in a pitch black room and check the time on your
by londons_explore 4y ago
I am disappointed that many phones/tablets don't go very dim.
From flagship to cheap, it seems that if you're in a pitch black room and check the time on your phone, the light will illuminate the whole room, even on the dimmest setting.
I actually modded my phone by putting a resistor in the LED backlight circuit, which divided the brightness by 1000 - and it was still plenty bright at night (human eyes are logarithmic, so dividing the brightness by 1000 doesn't have as much visual impact as you'd expect).
- greggsy 4y agoIt’s possible to set a custom filter in iOS, which reduces the brightness even further, but only in one colour, ie red. Better than nothing. The main issue i think is that backlights tend to flicker at low brightness.
- londons_explore 4y agoThey do... But thats down to poor design decisions. Human vision extends from about 10^5 cd/m^2 to 10^-5 cd/m^2 [1]. Typical backlights use something like PWM to modulate the brightness. That means you need to be able to scale your backlight by a factor of 10^10 to cover the whole human vision range. And if your CPU runs at 1 Ghz (10^9), then at the dimmest setting then even being on for a single clock cycle would be a flash every 10 seconds - clearly unacceptable, and even then, few backlight controllers could handle a 1 nanosecond pulse! The fix is to use PWM combined with settable 'modes'. The modes could be 'bright light' (using all the backlight LED's, perhaps a few watts total), and a dim light mode, which uses just one LED through a high value resistor, of just a few tens of microwatts. Your two modes have a factor of 10^5 between them in brightness. So now the PWM on your CPU only needs a resolution of 10^5, which it can do. [1]: https://www.researchgate.net/figure/Approximate-luminance-ranges-of-human-vision-and-corresponding-photoreceptors_fig2_50297383 https://www.researchgate.net/figure/Approximate-luminance-ra...
- formerly_proven 4y agoCompare your hypothetical 10^10 range to the range offered by typical LCD monitors, where maximum is in the 300...400 cd/m² range and a minimum brightness less than 30 cd/m² is "outstanding". I.e. a 1:10 range.
- ilyt 4y ago> That means you need to be able to scale your backlight by a factor of 10^10 to cover the whole human vision range. Uh, phones don't produce brightness that high. And the low range is "too low" for usefulness anyway. Your math is off by few factors > And if your CPU runs at 1 Ghz (10^9), then at the dimmest setting then even being on for a single clock cycle would be a flash every 10 seconds - clearly unacceptable, and even then, few backlight controllers could handle a 1 nanosecond pulse! CPU is not doing PWM, it's separate chip And you can't realistically have more than few kHz of PWM frequency anyway coz of losses. It's not really a technical problem in the first place, it's easy technically, just have 2 current sources, when you need low light you just PWM the low current one. And not "just putting resistor in series", that's extremely wasteful, or "single led" that would just not illuminate evenly.
- londons_explore 4y agoUnfortunately at these low currents, you tend to get a tiny amount of leakage across the LED junction - just a few microamps, but trying to make a small amount of light it becomes an issue. Worse, you can't even calibrate for it because the leakage is highly temperature dependant.
- ilyt 4y agoshrug kindle manages.
- mike_h 4y agoThere’s a full-color dimming filter in Accessibility -> Zoom -> Zoom Filter -> Low Light. You can assign it to the accessibility shortcut for quick access.
- nathancahill 4y agoGame changer. Thanks so much for this.
- oblio 4y agoMost Android devices have an "extra dim" option hidden somewhere in the buttons at the top (you might have to add it yourself from the extra buttons). Samsung: https://www.samsung.com/au/support/mobile-devices/activate-extra-dim-setting-on-samsung-device/ https://www.samsung.com/au/support/mobile-devices/activate-e... It's really dim, one time in the morning I thought the phone screen was off and it was just set to extra dim :-))
- nullify88 4y agoNot on my Galaxy S10 unfortunately. I have to resort to using Darker (https://play.google.com/store/apps/details?id=com.mlhg.screenfilter https://play.google.com/store/apps/details?id=com.mlhg.scree...)
- bick_nyers 4y agoThank you for the recommendation, game changer
- nikvdp 4y agoiOS actually has a hard to find setting that lets you make the screen super dim. It's been a lifesaver when using my phone in the evening. To enable it go to Settings -> Accessibility -> Zoom and then tap the Zoom toggle switch. Once that's enabled iOS will now bring up a super secret popup menu whenever you double tap the screen with three fingers. From the little popup menu go to Choose Filter -> Low Light and your screen will go dimmer than is normally possible. With this on and the normal brightness mode set to its lowest setting the screen can get quite dim indeed.
- spirit557 4y agoDo you know does this actually lower the backlight or is it changing gamma or something like that. I'll try it anyways thanks
- londons_explore 4y agoiphones are all OLED now, so there is no distinction. On an old LCD display there are some filters that do a linear/nonlinear mapping from 0->255 brightness to 0->64 for example, leaving the actual backlight at the same brightness. The downside is that colour banding and quantization start to get really bad - and 'black' starts to look very non-black.
- spirit557 4y agoMy older iphone is not oled so that would explain why I did not like this setting when I tried it some time ago like what you say about blacks looking out of balance. Thanks
- thinkmassive 4y agoThe latest iPhone SE still has an LCD screen. It was released in 2022 and is still a current model.
- jug 4y agoYes, I use this trick. You can adjust the filter to your heart's content. But I agree with the parent here that it should go dimmer as-is and we shouldn't need this. I'm not sure how light perception works, if it's a logarithmic thing like noise, but if not, this scale should probably be logarithmic instead. Or even moreso if it already is. Because I think we generally don't care exactly how bright it is if it's bright daylight and we need to max it, but conversely care much more for reaching the dimmest levels if we're in bed (or if we don't care, we probably should according to the article).
- bayindirh 4y agoI use a Kobo eBook reader and an iPhone X. My iPhone can go super dim, to the point that it's hard to see in a dark room. I use no special features. Also, Kobo's eBook readers can go very very dim, and can be comfortably read in a zero light room. The max brightness I use is 29%-31%, dependent on lighting. My reader has a fixed light, but newer ones also adjust light temperature automagically, and much more comfortable to read (got one as a present for my dad).
- deleted 4y ago[deleted]
- _dan 4y agoA Macbook's minimum brightness is quite bright. The thing that annoys me no end is that if you hit the "dim" button when it's at minimum brightness, it goes black - but fades out slowly and smoothly. So they're clearly capable of being dimmer, but Apple decided we're not allowed that.
- agravier 4y agoI've been using https://lunar.fyi/ https://lunar.fyi/ to go below the min brightness and also beyond the max brightness on an M1, works very well.
- skhm 4y agoSuch a great application. Lets me easily work outdoors in the summertime at XDR 100%
- kule 4y agoBeen a while since I used a MacBook but can't you do Shift+Opt (or just Opt?) Brightness+/- for an incremental change still? Works with volume too.
- lancesells 4y agoI never knew this. Thank you for the tip.
- gymbeaux 4y agoEven the dimmest fractional setting isn't dim enough for a pitch-black room imo
- abakker 4y agoI love apple devices, but man, these undocumented things make me question whose team their UI people are on. It doesn't feel like they're on my team.
- JohnFen 4y ago
- maxerickson 4y agoSome of it is probably adaptive vision. My Pixel 6 with an OLED screen doesn't work very good as a walking light in a dark room.
- washadjeffmad 4y agoAlso a Pixel owner - Try wiggling the light as you walk. Your motion sensing kicks in before either your focus or dark vision, and even if you can't "see" it, your brain can get enough information to let you navigate.
- maxerickson 4y agoI pointed that out because it is pretty dim, I don't try very hard to use the screen as a light.
- shanebellone 4y agoThe Google Pixel has a number of settings for this. It has the standard slider, extra dim, night, and grayscale modes. I always laugh when I see competition over brightness. I cannot wait for e-ink monitors to improve and wish someone would make an e-ink phone. Edit: Those settings might be standard on Android and not actually Pixel specific.
- washadjeffmad 4y agoI keep Extra Dim on at all times to lower the peak nits and to further dim the screen when using Night Light to read after dark. The biggest saviors to my longtime night reading habits, though, have been OLED and how many websites and ebook apps have competent true black dark modes.
- aembleton 4y agoDark Reader addon is good for this and works on Firefox for Android https://addons.mozilla.org/en-US/firefox/addon/darkreader/ https://addons.mozilla.org/en-US/firefox/addon/darkreader/
- ZeroCool2u 4y agoOne of my favorite features on my Pixel 7 Pro is the "Extra Dim" feature, especially since the Netflix app has started enforcing a minimum brightness level that's much too high in dark environments.
- toss1 4y agoAnother solution may be to use filtering glasses. Not "blue light glasses" but an FL-41 tint, which can help with migraines, light-sensitive conditions, and circadian rhythm issues[0]. This is a pinkish or amber-ish color tint. What I find far more concerning is the brief mention in the article about the explosion in outdoor lighting, which is massively disrupting the little remaining wildlife we have left (and nevermind destroying any hope of a glimpse t a dark sky). And there is absolutely zero reason for it other than ignorant wrong ideas that it helps traffic accidents or reduces crime (it does the opposite). Calling it cargo-culting would be kind. [0] https://health.clevelandclinic.org/do-blue-light-blocking-glasses-actually-work/ https://health.clevelandclinic.org/do-blue-light-blocking-gl...
- yanko 4y agoEye patch for sleep resolve sleeping issues and is priceless
- tbrock 4y agoYou can make the side button triple click on iPhone toggle application of an accessibility setting that lowers the brightness.
- eddyg 4y agoThis is how I activate/deactivate the “Zoom” accessibility setting with the “Low Light” filter (and the zoom level stays at 100% unless I double triple-finger tap!)
- is_true 4y agoFor those that don't want to mod their phone. What I do is set brightness at min + blue light filter set to max.