3 ms·

Can you list the actual chips you’re referring to and additional sources to follow? I’ve finally started playing with ESP32 and recently getting curious about t

by random3 2mo ago

Can you list the actual chips you’re referring to and additional sources to follow? I’ve finally started playing with ESP32 and recently getting curious about the smallest possible things out there. Also

kreelman 2mo ago
Here's the CH32v003, https://github.com/openwch/ch32v003 https://github.com/openwch/ch32v003 These are pretty low end and are fairly available at low cost. Here's a youtube of someone talking through some of the the CH32 boards, https://www.youtube.com/watch?v=Kss6WQvJbRs https://www.youtube.com/watch?v=Kss6WQvJbRs He talks about them being the "10c/chip" chip. Then, there is the CH32v303 https://www.wch-ic.com/products/CH32V303.html https://www.wch-ic.com/products/CH32V303.html, which is the lower end of the chips that support minimal floating point and USB host/client. These ones are a bit more pricey, https://www.lcsc.com/product-detail/C5456849.html https://www.lcsc.com/product-detail/C5456849.html at $US1.72 each. The extra price is QFP64 (64 pins, quad flat pack) and more features on the chip, USB, CAN, V4F extension giving one instruction multiply and some floating point operations. Note that the fact that this chip uses an extension, V4F, for floating point (I think?) is part of the argument of Dmitry's piece on the RISC-V. The chip is pretty low price for a fair bit of power.
- rasz 2mo ago
  CH32v303 costs more than much more capable ARM based RP2354A
  - phire 2mo ago
    And on the RP2354 you can swap one or both ARM cores for RISC-V cores at boot. I think the CH32v303's single V4F core might be slightly more capable than the Hazard 3 cores RISC-V cores (as it has a hardware FPU), but for everything else the RP2354 is probably better (and the ARM cores do have hardware FPUs)
  - hakfoo 2mo ago
    I feel like the Raspberry Pi products are inherently a special case. They're probably produced in far greater numbers than most off-the-shelf STM32 or CH32V chips. You've got a huge ready market in hobbyist/educational products as well as the commercial products that have used it as a convenient choice. There's that whole non-profit/educational heritage around them that likely selects for a different set of defaults and features than, say, a MCU designed specifically to be the controller for a SATA SSD or a $19 Roku clone. They also have a small product range, as compared to the broad product matrix a lot of the more "commercial brand" MCUs come in. I know even the CH32v30x chips come in several variations multiplied by several package options (which vary enough to impact the features you can realistically use on them).
    - crote 2mo ago
      > They're probably produced in far greater numbers than most off-the-shelf STM32 or CH32V chips. I highly doubt it. The RP2xxx lacks the built-in functionality for use in, say, a car, and it isn't cheap and fully-integrated enough for dime-a-dozen gadget application. They are great for hobbyists due to their low barrier to entry, but there really isn't a niche they serve when it comes to mass-produced electronics.
      - ajsnigrutin 2mo ago
        > They are great for hobbyists due to their low barrier to entry, but there really isn't a niche they serve when it comes to mass-produced electronics. This. Just programming a microcontroller is generally a pain, but a pain that hardware manufacturers can deal with, because they have employees with experience, who can read the long datasheets, get proper programmers and run the manufacturers software packages to program everything. For hobbyists, you're basically limited to arduinos, esp??/??, and rpi picos, only those are guaranteed to have a lot of software support, documentation, easy availability on aliexpress etc. for cheap, and can be made to actually do some stuff in an afternoon of tinkering. (technically it's the same with proper RPis, where they're the only SBC board (not x86 baed) that you're guaranteed will have at least some software support after 5+ years).
  - crote 2mo ago
    The "much more capable" is debatable. The RP2000 series is quite disappointing IO-wise: no timers, barely any ADC, no touch sensors, no CAN, bare minimum of USART/I2C/SPI, no I2S, no I3C, no ethernet, no USB PD... And yeah, it has its PIO modules, but those aren't powerful enough to make up for it. They are fine as an alternative to bitbanging Neopixels, but you can't rely on some hobbyist's vibe-coded weekend PIO project which takes up all the PIO slices and 30% of one core to do application-critical communications. I would take an RP2000 in a heartbeat for most of my hobbyist products, but for anything professional an STM32 is orders of magnitudes better, and even a CH32v303 looks like a more attractive option at first glance.
  - h3lp 1mo ago
    RPi is not less expensive; current Qty 1 lcsc price for rp2354b is $1.62, whereas ch32v303 is $0.88
- random3 2mo ago
  thank you!

by random3 2mo ago

kreelman 2mo ago

Here's the CH32v003, https://github.com/openwch/ch32v003 https://github.com/openwch/ch32v003 These are pretty low end and are fairly available at low cost. Here's a youtube of someone talking through some of the the CH32 boards, https://www.youtube.com/watch?v=Kss6WQvJbRs https://www.youtube.com/watch?v=Kss6WQvJbRs He talks about them being the "10c/chip" chip. Then, there is the CH32v303 https://www.wch-ic.com/products/CH32V303.html https://www.wch-ic.com/products/CH32V303.html, which is the lower end of the chips that support minimal floating point and USB host/client. These ones are a bit more pricey, https://www.lcsc.com/product-detail/C5456849.html https://www.lcsc.com/product-detail/C5456849.html at $US1.72 each. The extra price is QFP64 (64 pins, quad flat pack) and more features on the chip, USB, CAN, V4F extension giving one instruction multiply and some floating point operations. Note that the fact that this chip uses an extension, V4F, for floating point (I think?) is part of the argument of Dmitry's piece on the RISC-V. The chip is pretty low price for a fair bit of power.

rasz 2mo ago
CH32v303 costs more than much more capable ARM based RP2354A
- phire 2mo ago
  And on the RP2354 you can swap one or both ARM cores for RISC-V cores at boot. I think the CH32v303's single V4F core might be slightly more capable than the Hazard 3 cores RISC-V cores (as it has a hardware FPU), but for everything else the RP2354 is probably better (and the ARM cores do have hardware FPUs)
- hakfoo 2mo ago
  I feel like the Raspberry Pi products are inherently a special case. They're probably produced in far greater numbers than most off-the-shelf STM32 or CH32V chips. You've got a huge ready market in hobbyist/educational products as well as the commercial products that have used it as a convenient choice. There's that whole non-profit/educational heritage around them that likely selects for a different set of defaults and features than, say, a MCU designed specifically to be the controller for a SATA SSD or a $19 Roku clone. They also have a small product range, as compared to the broad product matrix a lot of the more "commercial brand" MCUs come in. I know even the CH32v30x chips come in several variations multiplied by several package options (which vary enough to impact the features you can realistically use on them).
  - crote 2mo ago
    > They're probably produced in far greater numbers than most off-the-shelf STM32 or CH32V chips. I highly doubt it. The RP2xxx lacks the built-in functionality for use in, say, a car, and it isn't cheap and fully-integrated enough for dime-a-dozen gadget application. They are great for hobbyists due to their low barrier to entry, but there really isn't a niche they serve when it comes to mass-produced electronics.
    - ajsnigrutin 2mo ago
      > They are great for hobbyists due to their low barrier to entry, but there really isn't a niche they serve when it comes to mass-produced electronics. This. Just programming a microcontroller is generally a pain, but a pain that hardware manufacturers can deal with, because they have employees with experience, who can read the long datasheets, get proper programmers and run the manufacturers software packages to program everything. For hobbyists, you're basically limited to arduinos, esp??/??, and rpi picos, only those are guaranteed to have a lot of software support, documentation, easy availability on aliexpress etc. for cheap, and can be made to actually do some stuff in an afternoon of tinkering. (technically it's the same with proper RPis, where they're the only SBC board (not x86 baed) that you're guaranteed will have at least some software support after 5+ years).
- crote 2mo ago
  The "much more capable" is debatable. The RP2000 series is quite disappointing IO-wise: no timers, barely any ADC, no touch sensors, no CAN, bare minimum of USART/I2C/SPI, no I2S, no I3C, no ethernet, no USB PD... And yeah, it has its PIO modules, but those aren't powerful enough to make up for it. They are fine as an alternative to bitbanging Neopixels, but you can't rely on some hobbyist's vibe-coded weekend PIO project which takes up all the PIO slices and 30% of one core to do application-critical communications. I would take an RP2000 in a heartbeat for most of my hobbyist products, but for anything professional an STM32 is orders of magnitudes better, and even a CH32v303 looks like a more attractive option at first glance.
- h3lp 1mo ago
  RPi is not less expensive; current Qty 1 lcsc price for rp2354b is $1.62, whereas ch32v303 is $0.88
random3 2mo ago
thank you!