5 ms·
Arduino is at work to make bio-based PCBs
- crote 2y agoI wonder how it compares to FR-2, an older paper-based PCB substrate. These new bio-based PCBs seem to have some characteristics closer to that than to regular FR-4.
- jdietrich 2y agoPoorly. PLA has a notoriously low heat deflection temperature, losing nearly all yield strength above about 60ºC. Any 3D printing enthusiast will know that PLA turns into a wet noodle in a hot car. Unless they've made a significant breakthrough in polymer chemistry, this substrate just won't work for the vast majority of applications.
- userbinator 2y agoIn other words, it's just stupid eco-virtue-signaling at its best.
- serf 2y agoPLA is too vague to know anything like that about. There are 100% 'bio' PLA variants with HDT values over 130c+, colorfabb PLA-HP comes to mind.
- jdietrich 2y agoPolylactic acid is polylactic acid. It has known properties. I don't know what Colorfabb's PLA-HP filament is actually made of, but it obviously isn't PLA; it's almost certainly some kind of proprietary (and therefore non-recyclable) co-polymer. "Bio-based" is a very different claim to "biodegradable".
- userbinator 2y agoand built to last in every sense. Strong doubt. All this is just greenwashing planned obsolescence to make things self-destruct more quickly, so they can keep selling you more.
- Animats 2y agoFrom the actual paper: "The resulting yield of PCB production was around 50%. Signal analysis was successful with analogue data acquisition (voltage) and low-frequency (4 kHz) tests, indistinguishable from sample FR4 boards. Eventually, the samples were subjected to highly accelerated stress test (HAST). HAST tests revealed limitations compared to traditional FR4 printed circuit materials. After six cycles, the weight loss was around 30% in the case of PLA/Flax, and as three-point bending tests showed, the possible ultimate strength (25 MPa at a flexural state) was reduced by 80%."[1] This sort of problem has come up many times with attempts to put some biological filler material into a composite. Most biological materials absorb and release water, and change size and weight as they do. This causes trouble for anything exposed to humidity changes. The classic "hemp/soybean car" ran into this problem.[2] In 1941, plastics were more expensive, and there were attempts to find some cheap material to use as filler. That never got beyond a prototype. Modern attempts at bio-composites seem to hit the same problem.[3] This might have potential for cheap disposable toys, where expected lifetime is in months and disposal as ordinary trash is desirable. [1] https://iopscience.iop.org/article/10.1088/1361-6528/ad66d3 https://iopscience.iop.org/article/10.1088/1361-6528/ad66d3 [2] https://en.wikipedia.org/wiki/Soybean_car https://en.wikipedia.org/wiki/Soybean_car [3] https://en.wikipedia.org/wiki/Biocomposite https://en.wikipedia.org/wiki/Biocomposite
- userbinator 2y agoThis might have potential for cheap disposable toys, where expected lifetime is in months and disposal as ordinary trash is desirable. ...as if anyone wanted more of that.
- harvey9 2y agoI took it to mean they would be biodegradable.
- hulitu 2y ago> I took it to mean they would be biodegradable. > I took it to mean they would be biodegradable. The only biodegradable materials are plants and animals. Plastic (however "green") is not. You still get small pieces of plastic from it.
- awei 2y agoFor a moment I thought they were making hobbyist PCBs you can put in your body.
- gitroom 2y agoGotta say, I keep wanting these bio-PCBs to be awesome, but tbh the durability stuff always throws me off. Kinda blows when things gotta get tossed every couple months.
- deleted 2y ago[deleted]
- klysm 2y agoGreenwashing - this kind of idea has been floating around for years and I don’t think it’s really that big of a problem
- westurner 2y agoNo, we have environmentally and financially unsustainable supply chain dependencies on silicon-grade sand and other gases and minerals. PCBs are not biodegradable but could be. What is the problem?
- klysm 2y agoYou haven't pointed out anything specific to FR4, which is what this would be replacing. This is merely a ploy at getting funding, and I'm very skeptical about it because I've seen 2 or 3 companies do the exact same pitch and fail before.
- westurner 2y ago> The goal: to design and test bio-based multilayer PCBs that reduce environmental impact, without compromising on functionality or performance. What about cost? And so instead, What is a sustainable flame retardant for Graphene Oxide PCBs; and is that a filler?
- westurner 2y ago"Study of properties of graphene oxide nanoparticles obtained by laser ablation from banana, mango, and tangerine peels" (2025) https://www.sciencedirect.com/science/article/pii/S2666978125000200 https://www.sciencedirect.com/science/article/pii/S266697812...
- westurner 2y agoGraphene is free when you flash heat unsorted recycled plastic and sell or use the Hydrogen. Graphene can be produced from CO2. CO2 is overly-abundant and present in emissions that need to be filtered anyway. What types of graphene and other forms of carbon do not conduct electricity, are biodegradable , and would be usable as a graphene PCB for semiconductors and superconductors? Graphene Oxide (low cost of production), Graphane (hydrogen; high cost of production), Diamond (lowering cost of production, also useful for NV QC nitrogen-vacancy quantum computing; probably in part due to the resistivity of the molecular lattice), How could graphene oxide PCBs be made fire-proof? Non-Conductive Flame Retardants: phosphorous, nitrogen (melamine,), intumescent systems, inorganic fillers Is there a bio-based flame-retardant organic filler for [Graphene Oxide] PCBs?