4 ms·
I see you made a current limiter from a mosfet + resistor. I wonder if there are ready-made components that do the same, and also monitor overheating. Maybe not
by amelius 2y ago
I see you made a current limiter from a mosfet + resistor. I wonder if there are ready-made components that do the same, and also monitor overheating. Maybe not necessary in this case (because you're only limiting the inrush current, not a continuous current). There are current-limiting diodes but as far as I've seen they are only available for smaller currents.
- michaelt 2y agoYou can get single-chip current limiters for LED driver applications. A CL2N8-G for example. In some applications you can also use almost any linear voltage regulator - put a resistor between your linear regulator's ground and output pins, and you'll get a constant current. Of course if your application involves the amount of power dissipation that requires a heatsink, you'll probably end up with a discrete component for that anyway :)
- deleted 2y ago[deleted]
- amelius 2y agoLet's say I have a voltage source of 48V, and I want to limit current in my system to 4.5A, precisely, and with overheating protection. I could be wrong but I don't think the led-driver and voltage regulator solutions would fall in this range. Also, a heatsink would not be required if the duration in which the current needs limiting is small.
- namibj 2y agoYou can use a current limiting buck set to pass through input voltage up until the current limit.
- Animats 2y agoOh, you mean Q2-R5 in [1]? That was a late addition, and yes, it's a linear current regulator using a depletion-mode MOSFET. I did that because I didn't want to change the board layout much and it only took two components. Others have built this device, and having good protection circuitry means it works for them, not just me. Q2-R5 is not the inrush current limiter. The inrush current limiter is U2. That's an AP2553W6.[2] That's a part designed to solve a specific problem - plugging into a USB port. USB port ICs have overcurrent detection which will quickly turn off power from the port if you try to pull too much power. This keeps external devices from pulling down the +5 rail in a laptop or pad with limited power available. The port turns off until reset. (On Windows this used to take a reboot; Linux usually resets if you close and open the device.) So if you plug in something with a large filter capacitor, the inrush current as the capacitor charges can momentarily cause an overcurrent condition and shut the port down. The AP2553W6 has both a linear regulator and a switch. When everything is good, the switch is closed and power flows through. If there's a momentary overload, it current limits. If there's a steady overload, it cuts power. Devices which don't do this power startup properly are often the cause of problems mentioned in searches for "USB port stops working". Not doing this properly saves about $0.25 in parts cost in volume. Such devices will work fine plugged into a USB charger or a desktop machine, but may shut down a USB port on a laptop or tablet. (This is for USB-A. USB-C is more complicated.) [1] https://github.com/John-Nagle/ttyloopdriver/blob/master/board/images/schematic.png https://github.com/John-Nagle/ttyloopdriver/blob/master/boar... [2] https://www.diodes.com/assets/Datasheets/products_inactive_data/AP255x.pdf https://www.diodes.com/assets/Datasheets/products_inactive_d...
- amelius 2y ago> When everything is good, the switch is closed and power flows through. If there's a momentary overload, it current limits. If there's a steady overload, it cuts power. Yes I'm looking for a device family that can do exactly that, but for a large range of currents and voltages (48V, 5A max). Preferably with just two terminals.
- Animats 2y agoThat would probably be a self-resetting positive-temperature-coefficient fuse. Those are available for a wide range of currents. They're simple, cheap two-terminal devices.[1] Those are safety devices. If you're worried about a sudden load introducing a glitch on the 48VDC rail, you may need faster response. It wouldn't have worked in my application, because I need something that will current limit before the overload detector at the power source end trips. Here's a bigger current limit switch.[2] Versions are available that can handle 48VDC 5A. Texas Instruments calls it an "e-fuse". Not two-terminal, though; it needs some external resistors and caps, plus a connection to ground. Turns off in 280 nanoseconds on a short circuit. This is functionally similar to the part I used, but for higher voltages and currents in industrial applications. TI has many useful tech notes available. [1] https://community.element14.com/technologies/experts/b/comprehensive-guides/posts/a-comprehensive-guide-to-resettable-fuses https://community.element14.com/technologies/experts/b/compr... [2] https://www.ti.com/product/TPS1663 https://www.ti.com/product/TPS1663
- amelius 2y agoThanks!