4 ms·

I have the 70b model running quantized just fine on an M1 Max laptop with 64GiB unified RAM. Performance is fine and so far some Q&A tests are impressive. This

by api 2y ago

I have the 70b model running quantized just fine on an M1 Max laptop with 64GiB unified RAM. Performance is fine and so far some Q&A tests are impressive. This is good enough for a lot of use cases... on a laptop. An expensive laptop, but hardware only gets better and cheaper over time.

buu700 2y ago
I don't have the hardware to confirm this, so I'd take it with a grain of salt, but ChatGPT tells me that a maxed out M3 MacBook Pro with 128 GB RAM should be capable of efficiently running Llama 3.1 405B, albeit with essentially no ability to multitask. (It also predicted that a MacBook Air in 2030 will be able to do the same, and that for smartphones to do the same might take around 20 years.)
- hmottestad 2y ago
  I’ve run the Falcon 180B on my M3 Max with 128 GB of memory. I think I ran it at 3-bit. Took a long time to load and was incredibly slow at generating text. Even if you could load the Llama 405B model it would be too slow to be of much use.
  - buu700 2y ago
    Ah, that's a shame to hear. FWIW, ChatGPT did also suggest that there was a lot of room for improvement in the MPS backend of PyTorch that would likely make it more efficient on Apple hardware in time.
    - Klaus23 2y ago
      You fundamentally misunderstand the bottleneck of large LLMs. It is not really possible to make gains that way. A 405B LLM has 405 billion parameters. If you run it at full "prescision", each parameter takes up 2 bytes, which means you need 810GB of memory. If it does not fit in RAM or GPU memory it will swap to disc and be unusably slow. You can run the model at reduced prescision to save memory, called quantisation, but this will degrade the quality of the response. The exact amount of degradation depends on the task, the specific model and its size. Larger models seem to suffer slightly less. 1 byte per parameter is pretty much as good as full precision. 4 bits per parameter is still good quality, 3 bits is noticeably worse and 2 bits is often bad to unusable. With 128GB of RAM, zero overhead and a 405B model, you would have to quantize to about 2.5 bits, which would noticeably degrade the response quality. There is also model pruning, which removes parameters completely, but this is much more experimental than quantisation, also degrades response quality, and I have not seen it used that widely.
      - buu700 2y ago
        I appreciate the additional information, but I'm not sure what you're claiming is a fundamental misunderstanding on my part. I was referring to running the model with quantization, and was clear that I hadn't verified the accuracy of the claims. The comment about the MPS PyTorch backend was related to performance, not whether the model would fit at all. I can't say whether it's accurate that the MPS backend has significant room for optimization, but it is still publicly listed as in beta.
        Klaus23 2y ago
        Yes my mistake, I read your answer to mean that you think that the model could fit into the memory with the help of efficiency gains. I would be sceptical about increasing efficiency. I'm not that familiar with the subject, but as far as I know, LLMs for single users (i.e. with batch size 1) are practically always limited by the memory bandwidth. The whole LLM (if it is monolytic) has to be completely loaded from memory once for each new token (which is about 4 characters). With 400GB per second memory bandwidth and 4-bit quantisation, you are limited to 2 tokens per second, no matter how efficiently the software works. This is not unusable, but still quite slow compared to online services.
        buu700 2y ago
        Got it, thanks, that makes sense. I was aware that memory was the primary bottleneck, but wasn't clear on the specifics of how model sizes mapped to memory requirements or the exact implications of quantization in practice. It sounds like we're pretty far from a model of this size running on any halfway common consumer hardware in a useful way, even if some high-end hardware might technically be able to initialize it in one form or another.
        Klaus23 2y ago
        GPU memory costs about $2.5/GB on the spot market, so that is $500 for 200GB. I would speculate that it might be possible to build such a LLM card for $1-2k, but I suspect that the market for running larger LLMs locally is just too small to consider, especially now that the datacentre is so lucrative. Maybe we'll get really good LLMs on local hardware when the hype has died down a bit, memory is cheaper and the models are more efficient.
    - nl 2y ago
      Most "local model runners" (Llama.CPP, Llama-file etc) don't use Pytorch and instead implement the neural network directly themselves optimized for whatever hardware they are supporting. For example here's the list of backends for Llama.cpp: https://github.com/ggerganov/llama.cpp?tab=readme-ov-file#supported-backends https://github.com/ggerganov/llama.cpp?tab=readme-ov-file#su...
      - buu700 2y ago
        Ah okay, interesting, thanks.
- deleted 2y ago
  [deleted]
diffeomorphism 2y ago
Just for reference, the current version of that laptop costs 4800€ (14 inch macbook pro, m3 max, 64gb of ram, 1TB of storage). So price-wise that is more like four laptops.
- evilduck 2y ago
  I think they were referring to the form factor not the price. But even then the price of four laptops is not out of line for enthusiast hobby spending. Ever priced out a four wheeler, a jet-ski, a filled gun safe, what a "car guy" loses in trade in values every two years, what a hobbyist day-trader is losing before they cut their losses or turn it around, or what a parent who lives vicariously through their child and drags them all over their nearby states for overnight trips so they can do football/soccer/ballet/whatever at 6am on Saturdays against all the other kids who also won't become pro athletes? What about the cost of a wingsuit or getting your pilots license? "Cruisers" or annual-Disney vacationers? If you bought a used CNC machine from a machine shop? But spend five grand on a laptop to play with LLMs and everyone gets real judgmental.
karolist 2y ago
I have the same machine, may I ask which model file and program are you using? Is it partial GPU offload?

by api 2y ago

buu700 2y ago

I don't have the hardware to confirm this, so I'd take it with a grain of salt, but ChatGPT tells me that a maxed out M3 MacBook Pro with 128 GB RAM should be capable of efficiently running Llama 3.1 405B, albeit with essentially no ability to multitask. (It also predicted that a MacBook Air in 2030 will be able to do the same, and that for smartphones to do the same might take around 20 years.)

hmottestad 2y ago
I’ve run the Falcon 180B on my M3 Max with 128 GB of memory. I think I ran it at 3-bit. Took a long time to load and was incredibly slow at generating text. Even if you could load the Llama 405B model it would be too slow to be of much use.
- buu700 2y ago
  Ah, that's a shame to hear. FWIW, ChatGPT did also suggest that there was a lot of room for improvement in the MPS backend of PyTorch that would likely make it more efficient on Apple hardware in time.
  - Klaus23 2y ago
    You fundamentally misunderstand the bottleneck of large LLMs. It is not really possible to make gains that way. A 405B LLM has 405 billion parameters. If you run it at full "prescision", each parameter takes up 2 bytes, which means you need 810GB of memory. If it does not fit in RAM or GPU memory it will swap to disc and be unusably slow. You can run the model at reduced prescision to save memory, called quantisation, but this will degrade the quality of the response. The exact amount of degradation depends on the task, the specific model and its size. Larger models seem to suffer slightly less. 1 byte per parameter is pretty much as good as full precision. 4 bits per parameter is still good quality, 3 bits is noticeably worse and 2 bits is often bad to unusable. With 128GB of RAM, zero overhead and a 405B model, you would have to quantize to about 2.5 bits, which would noticeably degrade the response quality. There is also model pruning, which removes parameters completely, but this is much more experimental than quantisation, also degrades response quality, and I have not seen it used that widely.
    - buu700 2y ago
      I appreciate the additional information, but I'm not sure what you're claiming is a fundamental misunderstanding on my part. I was referring to running the model with quantization, and was clear that I hadn't verified the accuracy of the claims. The comment about the MPS PyTorch backend was related to performance, not whether the model would fit at all. I can't say whether it's accurate that the MPS backend has significant room for optimization, but it is still publicly listed as in beta.
      - Klaus23 2y ago
        Yes my mistake, I read your answer to mean that you think that the model could fit into the memory with the help of efficiency gains. I would be sceptical about increasing efficiency. I'm not that familiar with the subject, but as far as I know, LLMs for single users (i.e. with batch size 1) are practically always limited by the memory bandwidth. The whole LLM (if it is monolytic) has to be completely loaded from memory once for each new token (which is about 4 characters). With 400GB per second memory bandwidth and 4-bit quantisation, you are limited to 2 tokens per second, no matter how efficiently the software works. This is not unusable, but still quite slow compared to online services.
        buu700 2y ago
        Got it, thanks, that makes sense. I was aware that memory was the primary bottleneck, but wasn't clear on the specifics of how model sizes mapped to memory requirements or the exact implications of quantization in practice. It sounds like we're pretty far from a model of this size running on any halfway common consumer hardware in a useful way, even if some high-end hardware might technically be able to initialize it in one form or another.
        Klaus23 2y ago
        GPU memory costs about $2.5/GB on the spot market, so that is $500 for 200GB. I would speculate that it might be possible to build such a LLM card for $1-2k, but I suspect that the market for running larger LLMs locally is just too small to consider, especially now that the datacentre is so lucrative. Maybe we'll get really good LLMs on local hardware when the hype has died down a bit, memory is cheaper and the models are more efficient.
  - nl 2y ago
    Most "local model runners" (Llama.CPP, Llama-file etc) don't use Pytorch and instead implement the neural network directly themselves optimized for whatever hardware they are supporting. For example here's the list of backends for Llama.cpp: https://github.com/ggerganov/llama.cpp?tab=readme-ov-file#supported-backends https://github.com/ggerganov/llama.cpp?tab=readme-ov-file#su...
    - buu700 2y ago
      Ah okay, interesting, thanks.
deleted 2y ago
[deleted]

diffeomorphism 2y ago

Just for reference, the current version of that laptop costs 4800€ (14 inch macbook pro, m3 max, 64gb of ram, 1TB of storage). So price-wise that is more like four laptops.

evilduck 2y ago
I think they were referring to the form factor not the price. But even then the price of four laptops is not out of line for enthusiast hobby spending. Ever priced out a four wheeler, a jet-ski, a filled gun safe, what a "car guy" loses in trade in values every two years, what a hobbyist day-trader is losing before they cut their losses or turn it around, or what a parent who lives vicariously through their child and drags them all over their nearby states for overnight trips so they can do football/soccer/ballet/whatever at 6am on Saturdays against all the other kids who also won't become pro athletes? What about the cost of a wingsuit or getting your pilots license? "Cruisers" or annual-Disney vacationers? If you bought a used CNC machine from a machine shop? But spend five grand on a laptop to play with LLMs and everyone gets real judgmental.

karolist 2y ago

I have the same machine, may I ask which model file and program are you using? Is it partial GPU offload?