22 ms·
How the biggest plane would supersize wind energy
- gnicholas 3y agoHow much more energy can these large blades produce that it's worth inventing a new kind of airplane (and apparently a purpose-built airstrip for every destination) to ship them? And if they ever break and need fixing, do you have to go pick them up, take them in for repair, and bring them back? If they've raised $100M+, I assume these questions have been asked, but I'm just generally skeptical that the math makes sense.
- biomcgary 3y agoWhy not an airship at this scale?
- karmakaze 3y agoI was thinking the same, like the Hybrid Air Vehicles (HAV) Airlander 10.
- joak 3y agoThey cannot land when it's windy
- usrusr 3y agoWhen wind is faster than their maximum speed. Chances are they can take much higher wind speed than the elaborate truck ballet required to transport huge blades on the ground. Wind turbine installation isn't exactly an all-weather project as is.
- simne 3y agoSupport become very costly, because need very large hangars and special machines for large craft (Ukrainian Ruslans and Mriya was designed as off-road, and carry few tons of special equipment onboard, which is not good for economy). Second problem landing strips, which also are limited (limited length, limited width). As example, for small size and narrow-body planes, in US there are more than 6000 private airstrips, so they could nearly substitute automobiles, but if need landing strip for something large, they are only at very large airports and in special places, like military airbases and space centers, so just few for whole country. In the world, things are worse than in US, so most Antonov planes was designed to fly from ground road, and carry special equipment on board, but this made them less effective.
- almostnormal 3y ago> Second problem landing strips, which also are limited (limited length, limited width). Direct-to-tower delivery. Removes the need for transport on the ground for the last miles and the need for a crane.
- simne 3y agoThat is problem. You sure could make tiny strip (10m x 250m), nearly everywhere, even at the center of old city. But large planes need much larger strips, for example typical international airport have strip 30m x 1600m. Why so much difference, because economy. It is much more effective to make large strips in large cities (or near them), than to make off-road planes (google Bush plane) which will have much more expensive cost to transport weight-kilometer or passenger-kilometer. From where become expensiveness. Well, most effective planes flight fast at high atmosphere (because speed of sound is significantly higher in low pressure), but they also have high landing speed, and unfortunately, brakes (very similar to automobile) need to dissipate all energy from speed, calculated from simple formula (m*v^2)/2, so with double speed have quadruple energy. Energy dissipation from plane brakes is really big problem, so big that nearly all big planes have special "thermo-accumulating" weights inside landing gear, which considered to heat fast when braking and then few hours dissipate heat. Extreme example was Concord, on which brakes cooling about 11 hours after landing. Bush planes are slow, so they don't have this problem. Second problem, because of engineering considerations (physics), large planes usually are tall, but not too wide inside, and very big loads are just considered to transport in "horseman" configuration, mean load placed on top of plane, so need special crane to load/unload.
- almostnormal 3y agoGGGP was suggesting use of an airship.
- simne 3y agoAnd who will build network of hangars for it? Aliens?
- vipshek 3y agoFrom the article: > Radia estimates the larger turbines could reduce the cost of energy by up to 35% and increase the consistency of power generation by 20% compared with today’s onshore turbines. Not sure what that translates to in terms of energy output over time. As for the sibling "Why not airships?" question, the article says: > Blimps can’t land in windy conditions. Helicopters are more costly than airplanes, and flying with a dangling blade designed to catch wind would prove complex and dangerous.
- gnicholas 3y agoDoes this cost reduction factor in the cost of making a new airplane company? If they transport a million blades then the cost per blade is not that high. But if they only make 10,000 blades then it becomes more of a factor (especially if the useful life turns out to be not as long as predicted).
- youngtaff 3y agoPlus how long does each turbine need to operate for before it mitigates the CO2 and other pollutants produced by building and operating the plane?
- Retric 3y agoIf they move 3,000 blades for ~10MW turbines then a 20% improvement in capacity factor alone is worth 3,066,000 metric tons of CO2 year. Edit: (Ops 10Mw * 1,000 turbines * 0.5 tons from natural gas /MW * .35% capacity factor * 20% improvement * 24 * 365 hours, coal is roughly double that.) By comparison a commercial jet takes ~20 years to emit 1 million tons of CO2. https://www.reuters.com/business/aerospace-defense/boeing-jets-contribute-1-mln-tonnes-co2-emissions-each-data-2021-07-26/ https://www.reuters.com/business/aerospace-defense/boeing-je...
- myrmidon 3y agoAssuming: 500tons of fuel for the transport of the 3 blades (comparison: AN225 with higher max payload weight guzzled ~15tons/hour). You could have used that energy to produce 500000kg * 40MJ/kg * 40% = 8TJ. The turbine would need ~40d to produce this (~25% capacity factor, 10MW nameplate power): 8TJ / (10[MW] * 25% * 3600[s/h] * 24[h/d])
- baseline-shift 3y agoWe are headed for 20 MW now, so a wind farm with five 20 MW turbines is a typical size for many gas power plants; 100 MW. In the EU, there's testing facilities that are checking these at this 20 MW size now. Commercially at this point there's up to 17 MW operating in the North Sea.
- noneeeed 3y agoThat's awesome. I hadn't realised we were close to 20MW ones now. The Halide ones being installed in the North Sea are monsters, amazing engineering. I'm pretty pessimistic about climate change. But the way wind and solar just keep getting cheaper and better gives me a certain amount of hope.
- konschubert 3y agoSolar keeps getting cheaper. Wind has kind of hit a roadblock - probably because it can’t be made in China.
- konschubert 3y agoSolar keeps getting cheaper. Wind has kind of hit a roadblock - there is less innovation coming China than for solar.
- _ph_ 3y agoVery different things. There is basically only one solar panel size on the market. Which starts at $100. Making large solar installations means just getting more panels. This is great for cost reduction, as that most of the times goes along with ramping up production numbers. The production of the single panel doesn't get more complex though. Wind energy is also getting constantly cheaper, both due to cost reductions and due to making the wind generators larger and thus more efficient. Onshore wind energy is the cheapest in Middle Europe and if they could grow further, costs would go down accordingly. But even if production can deliver, getting the blades gets more and more difficult, so here we area.
- davedx 3y ago
- Arrath 3y ago> (and apparently a purpose-built airstrip for every destination) Having built a 64-turbine windfarm back in the 2000's (so they were likely smaller than they are now) a goodly chunk of the work involved was site prep in building access roads traversable by the cranes required to set everything up, and the massively over-length trailers carrying the blades. Things like maximum grade, radius of the turns, breakover angle etc were hugely important. Grading out and paving an airstrip when you already have an appreciable contingent of heavy earthworking equipment onsite and, likely, also a concrete batch plant to reduce the travel time for the concrete you're using for the foundations really isn't too big of a stretch!
- opwieurposiu 3y agoTheir website says it can land on a packed dirt airstrip, 6000ft long. I wonder if they would park all the nearby windmills during takeoff/landing, to avoid creating swirly air.
- throwup238 3y agoTurbulence created by the blades is negligible to a large plane. Planes this big can easily fly into hurricanes [1]. [1] https://en.m.wikipedia.org/wiki/Lockheed_WP-3D_Orion https://en.m.wikipedia.org/wiki/Lockheed_WP-3D_Orion
- ultrarunner 3y agoAt this size the plane's swirly air (wake turbulence) would be a more significant concern
- AtlasBarfed 3y agoThe alt energy transition needs some SERIOUSLY LARGE scale. I wish I had a super-caps lock for that. The fact that a custom transport plane and dedicated landing strip for massive wind farms is economically feasible should give you a hint as to what is at stake. For review, both wind and solar, allegedly with storage bundled in and without subsidies, is cheaper than the next cheapest (and fossil fuel based) generation method: natural gas turbine, per LCOE numbers from Lazard LAST YEAR. Natural gas turbine is basically topped out in terms of efficiency and cost, I believe they have already exceeded Carnot efficiency with downstream exhaust heat capture and other maximization techniques. They can't go lower. Wind? Likely has a decade of gradual cost improvement. Solar? Successful integration of perovskites might drop prices 50% or more in the next decade, plus usual economy of scale improvement. The economics are basically settled. The details are massive scale, load leveling, grid adaptation.
- schoen 3y agoDoesn't the Carnot engine capture the absolute thermodynamic optimum for extracting usable energy from a hot object? How do you beat it?
- _ph_ 3y agoWell, yes. If you have a combustion engine or a turbine, Carnot tells you exactly the maximal efficiency you could achieve. But the exhaust still can be used for residental heating. So while the generator doesn't get any more efficient at producing electricity, you can use the heat which drives up the overall gain of operating the generator.
- thsksbd 3y agoAs a first order approximation, power scales as the square of the radius. Of course, problems can scale faster the quadratically, transportation is one of them.
- adrianN 3y agoPower actually scales better than the square of the radius, because there is more wind at greater height.
- usrusr 3y agoAnd real nimby impact (as opposed to the impact imagined) scales much less than quadratic, because larger rotor implies lower rpm and rpm has a huge impact on perception. Small rotors emit a very strong "presence" when you are anywhere near, whereas the tallest ones feel as if they are on a different plane of existence even when you are standing right at the base. Certainly not quite as disconnected from reality as airliners passing by at cruising level, but it's a similar effect.
- thsksbd 3y agoThats linear scaling [1] so its still scaling quadratically. Ax^2 + Bx is a quadratic, after all! (Also, shouldn't the first order approx should neglect wind speed as a function of height?) [1] actually worse. From Wiki entry for "Wind Gradient" "Although the power law exponent approximation is convenient, it has no theoretical basis.[18] When the temperature profile is adiabatic, the wind speed should vary logarithmically with height,[19] Measurements over open terrain in 1961 showed good agreement with the logarithmic fit up to 100 m or so, with near constant average wind speed up through 1000 m.[20]"
- dimensional_dan 3y agoMaybe make them seaplanes if making airports is too expensive? I just want to bring seaplanes back any way we can really ;)
- _ph_ 3y agoWell, for any coastal location, you can just take a ship.
- fragmede 3y agoWhat is the smaller version of this? Just like I can buy a small solar panel that is able to charge a battery that I can then use to charge my phone. Is there a small windmill I can buy that can do a couple hundred watts?
- _ph_ 3y agoThere are small windmills available for purchase. For a while campers and sailing yachts would use them. But they seem to go out of fashion. The problem is: the efficiency goes up with the size also, there is more wind the higher you go. On top of all of that, windmills are quite noisy. You really cannot use them in residential areas. Solar cells are much easier these days and also cheaper.
- 7952 3y agoThe financial side is not just about energy output alone but includes other constraints and opportunities. A developer may get access to cheaper land and untapped wind resource or grid connection opportunities. A single project like that could make a lot of money. And critically it could be packaged into an opportunity that could be sold to banks and investors. Opening up new opportunities could easily justify a few tens of million in delivery costs.
- jauntywundrkind 3y agoIf the plane really is task built that would be super cool. Huge plane (108m/356ft), carrying pretty light cargo all in all (blades of this length weigh probably 20~25T), that ideally can land and takeoff on short runways (to maximize the number of airports it can deliver to). By compare, a 777 will be either 60 or 75m long and carry 220t, and itself weigh 160t. Neat idea. Being able to get bigger blades to sites would be great. It also would enable centralizing the production better, which could be an efficiency win; a couple big factories cranking out blades. There's a lot of practical scale-out this would enable. The plane really is pretty wildly proportioned. I'm not sure what the total internal volume/cross section is expected to be but that's a long plane! Carrying not much weight! The blades are big but not colossal: by compare, the offshore Vestas V164 10MW turbine has 160m blades (weighting 35t); this is being designed for ~100m. It's definitely good to ask what else such a craft might be useful for. The low capacity is an obvious downside, but if it can access lots of airfields that could be quite enticing. Edit: Missed this: With a capacity for 80 tons. That's a lot more than I expected! It doesn't seem to make sense to me, for the payload it'll carry. Also: The WindRunner includes shoulder-height tires and has the ability to land on a packed-dirt 6,000-foot runway, which would need to be built for each project. Well, that's neat & potentially immensely useful for a lot.
- gnicholas 3y agoInterestingly the article mentions oil and gas as a potential alternate/additional customer.
- johnea 3y agoLooks like WSJ is blocking archive.ph on this one...
- jauntywundrkind 3y agoThe first snapshot didnt show the paywall, https://archive.ph/SJJfC https://archive.ph/SJJfC
- bookofjoe 3y agohere: https://www.wsj.com/business/energy-oil/how-the-worlds-biggest-plane-would-supersize-wind-energy-2f116e9b?st=tntym2rop7jh70j&reflink=desktopwebshare_permalink https://www.wsj.com/business/energy-oil/how-the-worlds-bigge...
- Brian_K_White 3y agoThis one works, thanks.
- bookofjoe 3y agotry this: https://www.wsj.com/business/energy-oil/how-the-worlds-biggest-plane-would-supersize-wind-energy-2f116e9b?st=tntym2rop7jh70j&reflink=desktopwebshare_permalink https://www.wsj.com/business/energy-oil/how-the-worlds-bigge...
- Brian_K_White 3y agoblank
- xnx 3y agoI'm not able to open the WSJ link, but I found more info here: https://radia.com/windrunner https://radia.com/windrunner I like this kind of crazy thinking. I wonder if there are also scenarios where blades can be shipped by truck 95% of the way, but the "last mile" is by helicopter.
- karmakaze 3y agoYes most pay-walled articles aren't unique. I searched for "Radia Windrunner" and got a bunch of stories.
- bookofjoe 3y agoHere you go: https://www.wsj.com/business/energy-oil/how-the-worlds-biggest-plane-would-supersize-wind-energy-2f116e9b?st=tntym2rop7jh70j&reflink=desktopwebshare_permalink https://www.wsj.com/business/energy-oil/how-the-worlds-bigge...
- Brian_K_White 3y agodoes not work
- jemmyw 3y agoThe plane on that site looks like they took the back off then secured it back on with very large bits of duct tape
- Mistletoe 3y agoThank you this link is so much better than the wsj article anyway. You get the whole idea scrolling a few images and text.
- dwighttk 3y agoI’m assuming they can also take off from those semi prepared short strips, but it is kinda funny their timeline doesn’t mention that at all.
- mattmaroon 3y agoI doubt it. Federal highway infrastructure mandates only 14.5 ft clearance. These things are larger than that in diameter and must go on a flatbed (that is itself 2' off the ground or so.) Turning radii on highways are not sufficient for something 300 feet long either, I don't believe anything over 80' can be towed. Many states have lower limits than the federal government on length. The real question is how will it get from wherever that plane lands (which I assume must only be large airports, unless they plan on building private runways near installation sites, which I guess might not be cost-prohibitve relative to the cost of flying the world's biggest plane in once for each blade) to wherever it is going? So it may still be last mile by helicopter, I don't know how else you'd move it.
- baseline-shift 3y agoIt really doesn't seem like it could pencil out, as it carries only one blade at a time, that's three trips for each turbine - and most windfarms would have more than one. But I guess they think it does. Perhaps they can also deliver to offshore farms, which already have contracts. I know there is a shortage of the specialized ships to float their huge blades out. Also, I hope they've done their homework on NIMBY pushback on land which is pretty effective against wind farms even with regular sized turbines.
- NikkiA 3y agoAlso, wind farms with giant blades tend not to be built close to airports, for some obscure reason.
- giarc 3y agoLooks like they load 2 blades at a time. Check out the image on their site. https://radia.com/windrunner https://radia.com/windrunner
- tromp 3y agoThe image 3/4 down the page directly under "Specifications" with the transparency slider shows the rear of the plane only fitting the narrow tip end. It can fit multiple smaller blades but only 1 very large blade.
- pwagland 3y agoWell, the photos show at least two blades in there, top to tail.
- nharada 3y agoBy the time this gets certified will the blades have grown too large for it?
- nradov 3y agoThe company is vertically integrated. They control the size of the blades and will design them to fit inside the airplane.
- _ph_ 3y agoWell, certainly there will be soon the wish to transport even larger blades. But if the first gen works out and is successful, then they could build an even longer airplane. As most of the Airplane is basically an aerodynamic fairing around the blades, I don't see why not.
- jacknews 3y agoI would think a 'fleet' or swarm of lifting vehicles, airships, drones, etc would make more sense than pioneering an entire custom airplane of such scale.
- gnicholas 3y agoSame here. I understand it would be dangerous to transport something so large, exposed to the wind. But couldn't they partially assemble it and then do the last parts on-site?
- nradov 3y agoA turbine blade isn't something that you can partially assemble. They looked into building temporary blade factories on site but the analysis indicates that a custom airplane is cheaper and less risky.
- icegreentea2 3y agoGiven that lifting fleets/swarms don't exist, I think that scaling up a conventional aircraft is actually lower risk. Aside from the technical risk getting lifting fleets/swarms certified would be an extremely novel development. Super jumbo aircraft should have a much more smooth regulatory pathway. While the physical scale of the aircraft is huge, its actual lift capacity isn't groundbreaking. They quoted 80 tons. That's well within the capacity of today's military strategic lift (C-17s can lift 85 tons). And in terms of size comparison, compared to the An-225 (RIP), the quoted dimensions are 108m (Windrunner) vs 84m, 24m high 18m, 80m wingspan vs 88m. Certainly a non-trival increase in linear size, but it's not a magnitude leap either.
- dredmorbius 3y agoThis was one of my own first two thoughts on TFA, the other being that given this as a proposal, one clear advantage of offshore windfarms is that transporting construction modules to the site should be vastly more straightforward: ship or barge towers and blades directly. This could work for farms both in ocean waters or large lakes. But other than that, the idea that blades might be shipped by some other mode (overland, barge, special-purpose rail, possibly) to a proximate location, then drone-ferried to the actual construction site ... seems a more viable option. And yes, drone lift-swarms comprised of multiple units yoked together and lifting a blade or set of blades ... seems more viable. Distances travelled should be relatively short (roughly, 10s to a few 100s of km), transport speeds need not be high, and flight profiles could be quite low altitude. Even if not drones, a ferry aircraft that could transition between vertical and horizontal flight modes, similar to the Bell Boeing V-22 Osprey, but, say, with an open cargo frame, might be a better fit. These could take off from a standard runway if desired, but also land and take off vertically from a cleared landing zone (potentially a barge or floating dock, in the case of offshore farms). Airships might be another option, though the ballast problem (as cargo is offloaded, an equivalent weight of ballast would need to be onboarded to prevent the airship from floating away), and poor handling in even modestly windy conditions (likely around wind farms) would probably prove problematic.
- noneeeed 3y agoThis reminds me of the massive planes that Airbus use to transport wings etc around Europe. I remember seeing one of the early generation many years ago when my dad worked for British Aerospace (who were the British part of the consortium before they sold of their civil division). It was immense.
- pjerem 3y agoThe Airbus Beluga. Living near an Airbus factory I spot them frequently here. Impressive plane. Also pretty cute.
- noneeeed 3y agoSadly I'm a bit older than that :D In my case is was the earlier Super Guppy https://en.wikipedia.org/wiki/Aero_Spacelines_Super_Guppy https://en.wikipedia.org/wiki/Aero_Spacelines_Super_Guppy Dad used to work at the British Aerospace Filton site. I absolutely loved getting to go to their family open day.
- nradov 3y agoIt's interesting that they chose to design a fully enclosed cargo airplane. There was a proposal a while back for a flying "flatbed truck" which could carry bulky cargo on an open platform behind a pressurized cockpit. It seems like a similar design might work here. Fuel consumption would be high due to the extra drag but cargo operations would be easier. https://youtu.be/d-DM2eJIS9k?si=nN7gnJdyJ141UVpP https://youtu.be/d-DM2eJIS9k?si=nN7gnJdyJ141UVpP
- bilsbie 3y agoWhy wouldn’t they make a giant helicopter instead?
- _ph_ 3y agoBecause no one ever made a helicopter able to carry 80 tons? And helicopters are tricky and expensive.
- bilsbie 3y ago> Heavy lift helicopters are designed with impressive abilities to carry over 50 tons (1) Seems like we’re pretty close. (1) https://aerocorner.com/blog/heavy-lift-helicopters/ https://aerocorner.com/blog/heavy-lift-helicopters/
- _ph_ 3y agoJust that the strongest helicopter on the page can only lift 20 tons. Of course, it would be sufficient to lift a single blade in one go. Still, that would be a very complex operation requiring very good weather.
- bilsbie 3y agoAt this scale I wonder if they compared this with assembling the blades on site?
- neonate 3y agohttps://archive.ph/L94G0 https://archive.ph/L94G0
- cypherpunks01 3y agoAt the risk of asking a dumb question - why do wind turbine blades need to be transported in one single impossibly large piece? They are all composite materials, right? Can't they be manufactured in a couple pieces and fused together properly on-site, using technology that is a more economical as compared to designing and building new types of aircraft?
- fnordpiglet 3y agoI have no expertise of any sort but I would assume a contiguous fiber material would have higher strength and the fuse joint would be considerably weaker.
- icegreentea2 3y agoThey don't -need- to be. There are commercial options (see: https://www.ge.com/renewableenergy/wind-energy/onshore-wind/cypress-platform https://www.ge.com/renewableenergy/wind-energy/onshore-wind/... for example) with segmented blades. However, I understand that doing a composite/chemical joint basically involves setting up a mini-factory, since your joint quality will depend very much on being able to control the conditions. Mechanical joints require less on site infrastructure, but have an efficiency penalty (https://www.nrel.gov/docs/fy23osti/84397.pdf https://www.nrel.gov/docs/fy23osti/84397.pdf). In any case, I imagine Radia is betting on getting enough volume to make the development cost irrelevant. In the end, you had to transport the roughly the same amount of material onsite anyways, in roughly the same form factor. The cost of a fleet of aircraft can be amortized over a huge geographic span wind farms, while also being attractive from the perspective of delivering replacements. I definitely think segmented blades are a way forward, but I can also see Radia's argument. I can totally believe that the "real winner" is going to a combination of situation and execution.
- pineaux 3y agoI dont have any expertise either, but wouldnt it be more feasible to make a mobile factory that can be built on site? Power shouldnt be a problem, a huge cable needs to be laid anyway. Just turn it around after the job is done. Just have a traveling circus with a large construction tent. Trailers that connect to each other etc. Sound more feasible than a plane to be honest.
- mullingitover 3y agoOkay hear me out: just use the turbine blades themselves, which are wings, as wings. Slap them on a smallish fuselage, fly to the destination, truck the fuselage back.
- krapp 3y agoThey're twisted so that they rotate when they catch the air, which is not what you want plane wings to do to the fuselage they're attached to.
- TheDudeMan 3y agoTrain the AI to make it fly anyway. :)
- mullingitover 3y agoRight, in a windmill they're mounted at an angle for generating rotation. When you mount them on the fuselage you just set them at an appropriate angle for the aircraft.
- ultrarunner 3y agoThe airspeed will vary along the length of the blade, necessitating a twist to control the angle of attack for efficiency. A blade/wing that would fly would be stalled at the root and/or supersonic at tip, efficient in only a small ring. That's the twist.
- almostnormal 3y agoThe outer half is just a giant wing-tip, increasing efficiency but not producing lift. It would need half the turbines to turn the other way around to have left/right wings, doubling tooling cost for production. And it would need a runway of appropriate width, but maybe they could be mounted at significant v-shape. Return trip not on the ground. The fuselage, engines, ... would still be massive, but with a set of small "normal" wings.
- 3y ago
- ccleve 3y agoThe obvious way to do this would be with a heavy-lift helicopter, but the article says this: >Helicopters are more costly than airplanes, and flying with a dangling blade designed to catch wind would prove complex and dangerous. Um, why not enclose the blade in a tube? There are heavy-lift helicopters that can go 170 mph and carry 40 tons. No runway required.
- threeseed 3y ago> There are heavy-lift helicopters that can go 170 mph and carry 40 tons Looking at the list below they mention that the helicopters can accomodate the weight in total but not externally. So could be that the lifting mechanism is the limiting factor. https://www.fairlifts.com/helicopters/the-top-10-heavy-lift-helicopters-for-2024/ https://www.fairlifts.com/helicopters/the-top-10-heavy-lift-...
- spiritplumber 3y agoYou know, if there ever was a use case for a zeppelin, this is it.
- tuffff 3y agoI still wish CargoLifter had been led competently. They were overambitious and promised too much, but the concept was sooo convincing. https://en.m.wikipedia.org/wiki/CargoLifter https://en.m.wikipedia.org/wiki/CargoLifter
- usrusr 3y agoStarted too early I guess. Ten years later and the blade transport use case would have come in at just the right time to salvage the investment. Back when Cargolifter shut down, rotor sizes were still in a range where ground transport isn't all that challenging.
- quanto 3y agoto appreciate the scale of this new plane, the current (recently destroyed) record holder for the largest cargo plane was An 225 that could hold 70m objects lengthwise. It seems that the newly proposed plane can hold > 100m objects, so that is approximately 50% increase in cargo length. The additional ability to land on packed dirt strips is also a huge plus. I suspect that the final business model, as hinted by the last sentence in the article, may include significant revenue contribution from transporting other machineries. The recently lost An 225 had a long running operation transporting these, including another jumbo jet. Now that the An 225 is gone, there could be more market for this interesting beast of a plane.
- simon_000666 3y agoWouldn’t strapping it to the bottom of a blimp/airship have been simpler?
- simon_000666 3y agoOr multiple helicopters flying in formation - also a possibility? Or just a bunch of drones?
- usrusr 3y agoOr A Very Large Quadcopter, because they already know a thing or two about making large rotating airfoils with a hub full of neodynium and coils? My guess would be range is the limiting factor, helicopters struggle keeping themselves in the air for more than a few hours, before taking into account any meaningful payload. Fixed wing aircraft can achieve so much more range.
- _ph_ 3y agoWell, there are no large blimps/airships in production. Also, they are quite sensitive to windy conditions, and you want to errect the turbines in very windy places... On the other side, building a small amount of rather simple airplanes should be quite doable in todays day and age.
- fransje26 3y agoOK. Let's bring a bit of sense to this nonsense. - They are starting from scratch. - They have no build facilities, no supply chain, hardly any aircraft design team to speak of. - They are developing an oversized aircraft for 1 very specific type of cargo, meaning of little use for anything else. - They raised $100 million. Sorry, no. This is absolute nonsense, and a waste of money. To bring a bit of perspective, the development of the Airbus Beluga XL, according to Wikipedia, cost €1 billion. And that was with a design team with years of experience, starting from a fully certified design they knew inside-out, with an existing supply chain, and with knowledge of all the design pitfalls of such a design as they had, you know, already built a Beluga type aircraft before. There is a reason why the industry says it costs about $10 billion for a clean-sheet aircraft design. And that is for experienced design teams. Agreed, this plane will not have to care for passengers, but that will not reduce the development costs by 90%. And then we haven't addressed the elephant in the room: the usefulness of an oversized airplane designed to carry an oversized, lightweight cargo, that will probably be of absolutely no use for anything else. It will be extremely costly, and they will not be able to amortize that cost by offering their services to carry different types of cargo.
- davedx 3y agoHave you heard of SpaceX?
- fransje26 3y agoSidestepping the discussion about the billions in subsidies that SpaceX got or didn't get, and the technology transfers they might have, or not have benefited from, SpaceX actually has a broad market they can leverage to turn a good profit with the excellent product they designed. That will not be the case here, at all. Aircrafts are designed for very specific payload/range configurations, and are a lot less competitive once out of that optimum. A 100 m plane designed to carry 80 tons of blades over 2000 km is of little use to anybody else. It's not anywhere close to the loading capacity of a 747 they are comparing themselves with, and it can't even cross the Atlantic. And that is if they even hit their payload targets at all, which is easier said than done. And no, it is not magically going to carry 130 tons over 6000 km with a bit of tweaking. That's not how planes work.
- kleton 3y agoLand and sea logistics will always use less carbon per ton than an airplane. Using a ship to move offshore cargo is probably going to be 1/100th of the carbon footprint of an extravagant airplane.