5 ms·
We saw a Pi running underwater at CES in Las Vegas
- westurner 3y ago> there is a Raspberry Pi that has been running underwater in the lobby of HZO’s building for 525 days and counting. [...] > We’re not sure which treatment our tiny green computer got — HZO produces a number of specialised coatings. Perhaps the Raspberry Pi got a parylene coating, as that seems to be a highly water-resistant and submersible option. They also offer plasma-applied coatings that are apparently a good low-cost option if you’re not going to be chucking your tech into the deep on a regular basis
- porphyra 3y agoDoes the coating get ruined if you unplug and plug back in stuff such as the HDMI cable and power cord?
- not_the_fda 3y agoYes
- lxgr 3y agoHow so? The contacts themselves are probably fine without the coating, and which other parts would plugging and unplugging a cable into a port (re)expose?
- not_the_fda 3y agoIf you pull the plug, you break the seal. Water will be able to make contact with the connectors and create shorts between the signals.
- Andrex 3y agoWhat if you let them dry before plugging them back in?
- not_the_fda 3y agoA conformal coating is like putting a circuit board in a plastic bag. In this application they applied it around the connectors. If you remove the connectors, the seal is broken. If you break the seal and submerge the board in water you will have a short. Usually in these types of applications, you use DEUTSCH connectors https://www.te.com/usa-en/products/brands/deutsch.html?tab=pgp-story https://www.te.com/usa-en/products/brands/deutsch.html?tab=p... that have an o-ring to seal the connector and allow it to be exposed to the elements and provides a seal that also allows removing the connector.
- Andrex 3y agoThan you for the explanation! I get it now.
- westurner 3y agoHow would you do regenerative braking train couplers between engines and battery cars? (That at present have just an air hose to hold brakes open per Westinghouse, but no power wiring or data cabling or a spec yet) Would standard EV charger specs work for coupling battery train cars to engines and/or regenerative braking cars? Maybe at least 1 Gbps and PoE+ to support a mesh network for sensors? Presumably hyperloop teams have solutions for this?
- upon_drumhead 3y ago> and they’ve toured it around the country at various events for almost ten years now. It’s a gen 4 board which is only a few years old. Did they do this previously with older pi’s or was that a mistake in the article?
- gnabgib 3y agoThey link to a video[0] showing it was the OG RasPi in 2014 [0]: https://www.youtube.com/embed/Str9MnQapQ4?si=3dkT8IlF_B7VN0HV https://www.youtube.com/embed/Str9MnQapQ4?si=3dkT8IlF_B7VN0H...
- barbazoo 3y agoWhat would happen to an uncoated pi? Would the whole pi have to be coated? I just realized I know very little about that part of electronics.
- bruce511 3y agoThe problem with electronics in water is that water is an electrical conductor. So the circuit diagram for the board becomes "everything connected to everything else all at once". Which means, at best it doesn't turn on. At worst it creates a short and current flows from one point to another, usually blowing up some part. Electronics and water therefore are seldom friends.
- davidhyde 3y agoDistilled water does not conduct electricity. It is the dissolved ions in the water that allow electricity to conduct. You may be able to clean the PI to such a level that nothing dissolves into the water when it is submerged. https://techiescientist.com/does-distilled-water-conduct-electricity/ https://techiescientist.com/does-distilled-water-conduct-ele...
- analog31 3y agoGetting it that clean is hard. There's stuff like residual flux under the ball grid arrays and other surface mount components.
- namibj 3y agoAFAIK electrolysis will force you to utilize a scrubbing system anyways once you've got current passing through the water. But getting conductivity acceptably low is much less demanding than getting it this extremely low. E.g. some CO2 lasers are cooled with purified water to limit the current through it.
- analog31 3y ago
- jimmyswimmy 3y agoThere are a number of conformal coatings that can be used to keep a circuit board dry at fish tank pressures. Parylene is my favorite as it isn't too harsh on the board materials and coats even underneath the surface mount components. Doesn't usually stick to the board though so it's more of a perfectly sealed bag around the board. It's good for basically forever. If you unplug the connectors you rip a hole in the "bag" though and the connectors will corrode. The way around that is to use expensive hermetically sealed connectors that are designed to operate underwater. Each side of those will cost a few hundred USD for boring round connectors. I have never tried to run e.g. HDMI through a bulkhead but such a connector would probably be impressively expensive. Anyway the best thing about Parylene is you have to send your equipment out to have it applied, no do it yourself here. The spray on coatings are usually sticky, messy, and not that great overall in comparison.
- krasin 3y ago>The way around that is to use expensive hermetically sealed connectors that are designed to operate underwater. Each side of those will cost a few hundred USD for boring round connectors. In this respect, I highly recommend Cobalt series of connectors from Blue Trail Engineering: https://www.bluetrailengineering.com/professional-products https://www.bluetrailengineering.com/professional-products - they cost "just" tens of dollars each and are very good (I used them); quite popular with ROV community.
- montag 3y agoWhat does ROV stand for?
- jvanderbot 3y agoI'm guessing remote operated vehicle - e.g., remote controlled submarines.
- deleted 3y ago[deleted]
- 3y ago
- tamimio 3y agoAny thermal impact after the coating?!
- 9991 3y agoBeing submerged in water will substantially help thermals.
- alchemist1e9 3y agoIs it possible one could coat electronics like this, then submerge them in (distilled maybe) water within an ice pack, freeze them, then use them and the heat melts the ice?
- kadoban 3y agoYes. Freeze/thaw cycles are _remarkably_ destructive though. Water expands with insane pressure if it gets caught in any little cavities or grooves. You're very likely to destroy it over time, if not immediately.
- alchemist1e9 3y agoMaybe it could instead be within some type of very thin pouch/layer of dielectric liquid, like in immersion cooling, and then water/ice outside of that so the force of expansion from freezing could be distributed?
- tonyarkles 3y agoI’m not sure I’m following the end game here with freezing it. From what I recall ice is actually a pretty decent thermal insulator and since a given mass of ice is larger in volume than the same mass of water, you’d end up with a hole melting inside with… weird things happening as far as pressures go. If the goal is to keep the processor nicely chilled, you’d probably be better off running liquid water over/through the block of ice and then keeping the coated board chilled in the ice water bath. If you’re trying to get below 0C, you should probably keep using a liquid with a lower freezing point instead of having the board frozen in a block.
- YeBanKo 3y agoCan anyone elaborate how it is coated around connectors?
- not_the_fda 3y agoYou can't remove the connector without breaking the coating
- ta988 3y agoyou dip with the cables connected
- xtiansimon 3y agoDoes a product like this sneed to have a public Material Safety Data Sheet? https://en.m.wikipedia.org/wiki/Safety_data_sheet https://en.m.wikipedia.org/wiki/Safety_data_sheet