3 ms·

How much did that cost you to build? What kind of hardware did you use?

Max-q 3y ago
You actually don't need more than the ESP32 and the led matrix. The LEDs are connected in series and you send a bit stream of RGB. Each led had an internal shift register with one input pin and one output pin, connected to the next LEDs input pin. So one microcontroller with one output pin available is all you need. Since there is no clock signal, timing needs to quite tight. To find more information you can google WS2812 or Neopixel. Libraries to use the protocol exists for most microcontrollers. An ESP32 module is a good choice because it costs $2-3, includes wifi and BT, antenna or UF-L plug, and is pre-certified.
- thousandknives 3y ago
  Small misunderstanding. With hardware I meant the LEDs/LED matrix. What kind of LEDs did you use and how much did it cost you is what I wanted to know...
  - angus-prune 3y ago
    The information was in the post - ws2812 (or ws281x, there are variations) which are also known by the semi-brandname "neopixel". They come in various form factors including fairy lights, strips and matrixes. They are very easy to work with, and there are good libraries or open source platforms (eg wled) to run them.
  - dekhn 3y ago
    I made a little portrait frame and MCU that draws Conway's Life. https://www.amazon.com/gp/product/B09CTQ37DB https://www.amazon.com/gp/product/B09CTQ37DB (I got the 16x16 for $16). Another <$10 for the ESP32. A soldering iron ($40 for a pinecil), $verylittle for solder and hook up wire. In my case, a 3D printer ($500) plus filament ($20), and some design software ($500/year, because Fusion 360 expensive).
masto 3y ago
Rough estimate: I got the LED panels from AliExpress (https://www.aliexpress.us/item/2255799924064579.html https://www.aliexpress.us/item/2255799924064579.html), the price fluctuates from around $10-$12 each x 12, so round up to $150 for the lights. They practically give ESP32s away with an oil change, so you could call it done at that point, but I chose to use a QuinLED Dig-Quad (https://quinled.info/pre-assembled-quinled-dig-quad/ https://quinled.info/pre-assembled-quinled-dig-quad/) to make it easy to wire up and mount on the wall. That cost me about $60 shipped. And I added a MEAN WELL LRS-100-5 power supply for $20. Finally for the laser-cut frames, I burned up about $30 of wood, and there's some minimal amount of 3D printer filament as well. Along with the incidental things like having to buy a spool of 3-conductor cable, connectors, etc. So all together I'd guess it was around $300. A completely no-frills version could be maybe half that.
masto 3y ago
Here's a little more detail on the construction if you're interested: https://youtu.be/eojYicG_Kjs?si=6cBHOUdk0n9hVoUh https://youtu.be/eojYicG_Kjs?si=6cBHOUdk0n9hVoUh

You actually don't need more than the ESP32 and the led matrix. The LEDs are connected in series and you send a bit stream of RGB. Each led had an internal shift register with one input pin and one output pin, connected to the next LEDs input pin. So one microcontroller with one output pin available is all you need. Since there is no clock signal, timing needs to quite tight. To find more information you can google WS2812 or Neopixel. Libraries to use the protocol exists for most microcontrollers. An ESP32 module is a good choice because it costs $2-3, includes wifi and BT, antenna or UF-L plug, and is pre-certified.

thousandknives 3y ago
Small misunderstanding. With hardware I meant the LEDs/LED matrix. What kind of LEDs did you use and how much did it cost you is what I wanted to know...
- angus-prune 3y ago
  The information was in the post - ws2812 (or ws281x, there are variations) which are also known by the semi-brandname "neopixel". They come in various form factors including fairy lights, strips and matrixes. They are very easy to work with, and there are good libraries or open source platforms (eg wled) to run them.
- dekhn 3y ago
  I made a little portrait frame and MCU that draws Conway's Life. https://www.amazon.com/gp/product/B09CTQ37DB https://www.amazon.com/gp/product/B09CTQ37DB (I got the 16x16 for $16). Another <$10 for the ESP32. A soldering iron ($40 for a pinecil), $verylittle for solder and hook up wire. In my case, a 3D printer ($500) plus filament ($20), and some design software ($500/year, because Fusion 360 expensive).

masto 3y ago

Rough estimate: I got the LED panels from AliExpress (https://www.aliexpress.us/item/2255799924064579.html https://www.aliexpress.us/item/2255799924064579.html), the price fluctuates from around $10-$12 each x 12, so round up to $150 for the lights. They practically give ESP32s away with an oil change, so you could call it done at that point, but I chose to use a QuinLED Dig-Quad (https://quinled.info/pre-assembled-quinled-dig-quad/ https://quinled.info/pre-assembled-quinled-dig-quad/) to make it easy to wire up and mount on the wall. That cost me about $60 shipped. And I added a MEAN WELL LRS-100-5 power supply for $20. Finally for the laser-cut frames, I burned up about $30 of wood, and there's some minimal amount of 3D printer filament as well. Along with the incidental things like having to buy a spool of 3-conductor cable, connectors, etc. So all together I'd guess it was around $300. A completely no-frills version could be maybe half that.

masto 3y ago

Here's a little more detail on the construction if you're interested: https://youtu.be/eojYicG_Kjs?si=6cBHOUdk0n9hVoUh https://youtu.be/eojYicG_Kjs?si=6cBHOUdk0n9hVoUh