2 ms·
I'm adding USB to projects just as a power cable but I'm (still) trying to avoid surface-mount. The only USB connector I've found that is still through-hole is
by JKCalhoun 3y ago
I'm adding USB to projects just as a power cable but I'm (still) trying to avoid surface-mount.
The only USB connector I've found that is still through-hole is USB Mini-B so I am unfortunately stuck with that.
(I should mention I am building kits for hobbyists who are averse to tackling an SMD component — they make me nervous as well.)
- sokoloff 3y agoEven hobbyists should be able to handle a fat pitch part like a surface mount micro USB-B. (I’m talking about once they get over the mental block. :) ) With wings and small holes to help with rough alignment, I’d sure rather buy a kit with micro-USB than mini.
- kalleboo 3y agoAt this point I think I'd rather have a DC jack than mini-B I think I might even own more USB-A/C to DC cables than I own mini-B cables.
- dylan604 3y agoI'm perplexed by the desire to move away from DC jacks as well. Power needs 2 pins. Using a multipin connector knowingly to only use 2 pins is rather confusing.
- kalleboo 3y agoPersonally I would prefer USB-C for everything. I have plugged in the wrong DC adapter (wrong polarity or voltage but the same physical form factor) far too many times and killed too many things. Not to mention all the device-specific DC adapters that have been lost through the ages. But for a hobbyist device, the currently available USB-C jacks have pins that are too small to solder by hand so I'll settle there. It would be nice if hand-solderable breakout boards were cheaper and more commonly available (the DC trigger boards out there are a great start but typically have to be ordered direct from China) But for factory-manufactured goods, DC jacks need to die and be replaced with USB-C. Meanwhile there is no room anywhere for mini-B, micro-B, etc anymore, even on hobbyist devices. I'm not even sure I could even find a mini-B cable in a physical store nearby anymore.
- JKCalhoun 3y agoYeah, that's basically it. I have a drawer of barrel-jack wall warts but they all vary in diameter, polarity, voltage, current... USB is a nice standard 5V source.
- kalleboo 3y agoEven the confusion about USB-C devices and adapters is nothing compared to the insanity that is DC jacks. At least USB-C will just not work instead of destroy things. My parents had a D-link DSL modem and Router where both the devices looked pretty much the same (they were stackable), had the same DC jacks, the power adapters looked the same, but were different voltages, which you could tell in white-on-gray 12pt text.
- numpad0 3y agoDC barrel plugs aren't best in terms of contact stability, they can rotate and slide and create noises. Something with locking and indexing would be better, which USB-C don't quite qualify but I guess is close enough.
- bmicraft 3y agoThe "problem" with dc jacks is you have to know what voltage something needs, maybe years after your or someone else built it. With usb-c you might have to remember that it needs a power supply with 15V support, but it won't let out the magic smoke if you chose the wrong one.
- Pet_Ant 3y agoI've fried a couple things over the years plugging in the wrong power supply (always during a move/reno when multiple things were being replugged) so the ability to have the device negotiate it's own voltage from a standard source that can be reused is a blessing. I still have a collection of random wall worts from the past just in case, but never seem to have the one I need when something dies.
- pi-rat 3y agoDon’t forget that you can often through-hole mount cheap readily made module boards like the one above. Often without adding height.
- JKCalhoun 3y agoIt looks a little hacky, but I may have to succumb, ha ha.
- crote 3y agoThey do exist [0][1][2], but they're not really suitable for hobbyist kits either. Due to the pin density they aren't really any easier to solder than SMD. If I were to design a hobbyist kit, I'd probably just use a breakout board with the USB-C connector already soldered onto it. [0]: https://www.lcsc.com/product-detail/USB-Connectors_Jing-Extension-of-the-Electronic-Co-918-518K2023D50001_C399934.html https://www.lcsc.com/product-detail/USB-Connectors_Jing-Exte... [1]: https://www.lcsc.com/product-detail/USB-Connectors_XUNPU-TYPEC-306DDW-ARP16_C2840393.html https://www.lcsc.com/product-detail/USB-Connectors_XUNPU-TYP... [2]: https://www.lcsc.com/product-detail/USB-Connectors_Korean-Hroparts-Elec-TYPE-C-31-D-01_C707316.html https://www.lcsc.com/product-detail/USB-Connectors_Korean-Hr...
- JKCalhoun 3y agoThanks, looking at these 6P connectors, the through-hole mounts ought to make the SMT connectors easy to solder down. I'll pick a few up and try them out on my next PCB project. (Worst case I can pre-solder these to the PCBs in the kits.)
- the__alchemist 3y agoAs crote pointed out, you can get THT ones, but this sounds like an XY problem: I would reflect on why you (and the kit targets) avoid SMD, and if that's something you should consider doing.
- foldr 3y agoLet me be the nth person to say don't avoid surface mount. Temperature controlled soldering irons are cheap now. Once you have one, coarse pitch SMT parts are really just as easy to solder as through hole.
- junon 3y agoOut of curiosity, why is SMD avoided? In my experience (as a self-taught hobbyist), SMD is easier to work with given cheap equipment (an Amazon skillet, some aquatic sand, and a cheap tube of T5 paste).