3 ms·
If doing long runs just run fibre. gigabit Ethernet is about as fast as copper can get - yes 10gb Ethernet exists, but it is power hungry (one reason 2.5gigabi
by bluGill 4y ago
If doing long runs just run fibre. gigabit Ethernet is about as fast as copper can get - yes 10gb Ethernet exists, but it is power hungry (one reason 2.5gigabit starting to appear). You can send a lot more data with fibre, there are no cross talk issues, and it is cheaper than copper. Transceivers are still expensive though, so copper is best for shorter runs (within your house distances), but still everyone who might run some cable in the future should learn about fibre and how to work with it.
- ethbr0 4y agoI was looking at it. What's the current best home-hobbyist option for terminating? Last I checked, it looked like it made more sense to just buy pre-terminated, built-to-length cables.
- bluGill 4y agoThat is one of the downsides of fiber: you need to figure out your distances before hand and order the right length. One more reason to use copper in the house most of the time. Maybe some ~2ft lengths of fiber for use on your server rack where you need speed between the server and the switch.
- xattt 4y agoIs it still worth doing Cat 8 for stringing Ethernet in a new build, or is it okay to cheap out and just go with Cat 6a?
- crote 4y agoCat6a can do 10GB over 100 meters, cat8 can do 40GB over 30 meters. Current consumer hardware is starting to support 2.5G over 100 meter of cat5, and we miiiight see 5G over 100 meters of cat6 become common in a few years. If you're that worried about upgrade-ability, better stick to fiber.
- toast0 4y agoNote that the specs are 100 meters in a dense conduit. You can probably manage higher than rated speeds in a household environment which likely doesn't have dense conduit nor 100 meter runs. If you're wiring from scratch, sure put the best you can afford, but if you've got cat3 in your walls already, see what runs, your NICs aren't going to look at the label on the insulation. (For better or worse, ethernet speed negotation runs at 1Mbps and the specs don't contemplate testing conditions and reducing speeds until you get to the multi-gig (2.5/5/10g) equipment. Some equipment will drop to 100M in drivers though)
- bluGill 4y agoOnly time will tell. For now my best guess is cat 5e is still good enough for everything, but since cat6a is no more expensive may as well use that instead. God has not given me any indication on how the future will play out though, I could be wrong. Then again I might be right just because by the time you need more than cat6 there is a new cat 12 that you need. Only time will tell.
- simoncion 4y ago> Transceivers are still expensive though... 10Gtek sells 10gbit multi-mode SFP+ transceivers for ~10->15 USD per, depending on how many you buy at once. I have ten on my LAN and have had no troubles with them. (Now we "just" need to do something about how absurdly expensive 10gbit NICs are...) (And no, I had never heard of them before I bought a few. I figured that multi-mode SFP+ transceivers have been around for more than a decade, so there's no reason for them to be 50->80+ USD per... purchased from several of the cheapest manufacturers selling on Newegg, and found that 10Gtek's stuff worked fine.)
- FullyFunctional 4y ago10Gtek has worked well for me. I have several transceivers and DAC cables from them. Fiber is awesome for distance and speed, but few devices can take SPF+ so I have a bunch of bulky thunderbolt to SPF+ dongles. Hard-earned suggestion: LABEL your fiber cable on both ends with the LENGTH (and id while you are at it). Nothing worse than running the fiber only to have it a few feet too short in the end.
- simoncion 4y agoDamn. Labelling my cables with their length _would_ have been a good idea. Maybe I'll do that this weekend.
- arein3 4y agoFiber through the house is a PITA. The fiber cable is fragile, can't be bent and can't be tested/resized without special equipment. I wait to end my current contract with the internet provider and will switch to a new one that has normal equipment that allows to run ethernet trough the house.
- simoncion 4y agoFiber _totally_ can be bent. I have several fiber cables that I can wrap around my pinky finger, no problem. However, it is true that you can't usually expect fiber to survive the "yank really hard on it until it untwists" method of kink removal.