6 ms·
I mean, sure, but reterminating with a new, not broken RJ45 only takes 30 seconds, and they cost peanuts.
by madaxe_again 4y ago
I mean, sure, but reterminating with a new, not broken RJ45 only takes 30 seconds, and they cost peanuts.
- michael1999 4y agoHow do you re-terminate stranded cable? I struggle to terminate solid-core in less that 5 minutes.
- Mikealcl 4y agoEasier than you think but one of those things easier to show than do. Muscle memory skill.
- dekhn 4y agoWhat do you mean stranded? If you mean standard ethernet cable, it's 8 solid wires. Putting a keystone block takes about 1-2 minutes (with a tool). I spend more time figuring out which wire goes where than the actual retermination.
- jiveturkey 4y agopatch cable wire is stranded. the clip here is meant for use on patch cables and has nothing to do with keystones
- danuker 4y agoStranded as in each wire being made up of smaller wires. https://en.wikipedia.org/wiki/Wire#Stranded https://en.wikipedia.org/wiki/Wire#Stranded These are typical in pre-capped wires. While they allow more flexibility of the wire, their ends are hard (if not impossible) to change.
- dekhn 4y agoI've never seen stranded wire in an ethernet cable, but I see it's a thing. I occasionally turn my male-male ethernet into male-female with a keystone block and never see stranded. I dabble in electronics and I eliminate stranded wire whenever I find it. Some people love it but I find it really inconvenient.
- Akronymus 4y agoStranded ones are very common in patch cables.
- burntwater 4y agoSolid Ethernet cabling should generally only be used on permanent building cable that never move. Stranded should be used on patch cables and cables that get moved around. Beyond being more difficult to handle, regular movement will break solid copper, often leading to intermittent connectivity.
- wrigby 4y agoCable bought on long spools to install permanently is usually solid, while patch cables are usually stranded. Most of the time, you'll end up buying pre-terminated stranded cable, and all the cable you terminate yourself will be solid.
- kesor 4y agoDoes it even matter if the cable is solid or stranded? When you put on that new RJ45 connector the cables go into the connector with the insulation on.
- michael1999 4y agoI tried and failed three times. Gave up, and pulled solid cable. TIL that some rj45 connectors have multiple teeth, and interlock.
- klyrs 4y agoIt's quite a process, apparently. Amusingly, their "all-in-one" tool doesn't do it all. https://www.truecable.com/blogs/cable-academy/how-to-terminate-a-shielded-cat5e-internal-ground-pass-through-rj45-connector#page_comments=1 https://www.truecable.com/blogs/cable-academy/how-to-termina...
- supermatt 4y agoOH MY! Pass-through RJ45... Why havent I seen these before. Arghhh. Im going to have to order some now.
- CodeWriter23 4y agoYeah, I thought "what kind of newfangled abomination is this" earlier this year, grumbling it was all that was available at Home Depot at that moment. Pleasantly surprised upon using one though, what a great time saver.
- somat 4y agoThe trick is the jack, you need the plug for stranded cable. and don't try to use stranded plugs on solid core, as I found out the hard way it is nothing but pain.
- silversmith 4y agoNot much to it. Every individual wire is wrapped up, and stays that way. You just need the stranded cable caps with teeth that pierce through the individual wire wrapping when you crimp down on them. Keystones are a pain tho, nobody seems to make them for stranded cable. But you can terminate the cable coming out the wall with a standard cap, and shove a connector where a keystone would go in the socket. All those things I learned after accidentally buying tons of stranded cable for re-wiring my house :)
- CodeWriter23 4y agoYou have to use an RJ-45 for stranded cable, not solid.
- pxx 4y ago30 seconds? I can hardly even get the wires in the right order in that amount of time and don't get me started on shielded connectors...
- CodeWriter23 4y agoI hardly think this add-on clip is an appropriate fix for applications requiring shielded connectors.
- pantalaimon 4y agoEh maybe if you are used to doing it. I always fail miserably and the cable gets ever shorter.
- justsomehnguy 4y agoI mean, sure, but reterminating with a new, not broken patch cable only takes 30 seconds, and they cost peanuts. But sarcasm aside, you don't want to reterminate a pre-made patch cable. Under a very strange Universe fluctuations where you don't have a spare patch cord, spare 8p8c jack with a crimper but you do have a 3D printer with a plastic loaded and ready to print....