5 ms·
At what point will the wear resistance be so low from increasing the layers (and bits) per cell that flash becomes effectively write-once, read many (WORM)?
by Robotbeat 4y ago
At what point will the wear resistance be so low from increasing the layers (and bits) per cell that flash becomes effectively write-once, read many (WORM)?
- lazide 4y agoKeep in mind, these are layers of cells, not multi-level cells. Each of the layers has an individual multi-level cell. That said, Samsung quad-level cells only have 1k write lifetime, so likely not far off.
- hinkley 4y agoI love how someone said there's a septuple-level cell out there... but you have to immerse it in liquid nitrogen for it to work.
- __alexs 4y agoPLC NAND is already on the way to commercial hardware.
- deleted 4y ago[deleted]
- mritun 4y agoRemember, even 1000 writes means roughly 3Y of full drive writes per day with the naïve wear leveling and the most brutal write load. For most write loads the drives made of this kind of NAND can be easily warranted for 3Y.
- lazide 4y agoYeah, 1K is still in the range of reasonable (if the wear leveling isn't terrible), another order of magnitude decrease though and we're getting on the edge of not.
- cowtools 4y ago1k writes sounds good enough for consumer hardware I suppose. As long as there's some some type of S.M.A.R.T. system to warn the user before it wears out.
- gruez 4y agousually it goes into read-only mode when it wears out, so there's no data loss.
- cowtools 4y agothat's fantastic actually! One problem might be that programs don't anticipate this behavior, like if it wears out while a filesystem is still syncing
- blibble 4y agoall modern filesystems are either journalled or always consistent on disk, so shouldn't be a problem if it dies during worst case you have to copy it to another disk and replay the journal
- mgerdts 4y agoThis doesn’t account for the write amplification factor, which is quite unlikely to be 1 with a naive wear leveling implementation and the most brutal write workload.
- adgjlsfhk1 4y agonote that there are data structures (eg b epsilon trees) that can guarantee a write amplification factor of log_b(disk size) for very large b (over 1000). this means that if you are willing to sacrifice a small amount of sequential read speed, you can guarantee write amplification of no more than 4 (with a few mb of RAM).
- mgerdts 4y agoI've added [1] to my reading list. Do you have suggestions for others that relate specifically to WAF? 1. http://supertech.csail.mit.edu/papers/BenderFaJa15.pdf http://supertech.csail.mit.edu/papers/BenderFaJa15.pdf
- adgjlsfhk1 4y agoThe TLDR is that the design of b^e means that (other than the root node which you can store in RAM), you never need to write in chunks less than b^e (smaller writes get batched and pushed down the tree only when you have that much data to write to a child node). With the typical, e=1/2, you can set b=blocksize of SSD^2. This means that any small write will turn into 1 write per depth of the tree, and each of those writes will be writing a full block of data (so the maximal WAF is the depth of the tree). Also, for bigger writes, you can just write to the bottom directly, so this ends up working out such that for large sequential writes, you get a WAF of 1, and for small/random writes, you get a WAF of d.
- AtlasBarfed 4y agoYeah they are going to stacked cells because the endurance is so bad at smaller process nodes. SSD prices have stalled for quite a while. By now they should be getting in shouting distance of hard drives but unfortunately memory makers are much more of a colluding trust than Hard Drive manufacturers. What I really want is a high-lifetime write medium to go with SSDs. Hard disks aren't really it. It's too bad the DVD/CD form factor/drive died with high speed internet, holographic storage would have been great. But there was no investment/demand to push it.
- hinkley 4y agoLevels per cell and wear I understand. What's the link between circuit layer depth and wear?
- Dylan16807 4y agoIncreasing layers should cause roughly zero problems. As far as bits per cell, 4 already gives you very slow writes and not a lot of them. Let's say that maxes out at 5 or 6.
- deleted 4y ago[deleted]
- rowanG077 4y agoThermals? SSDs have slowly but surely increased in TDP.
- Dylan16807 4y agoFlash likes to run pretty hot and we still rarely attach heat sinks, even less often proper heat sinks with fins. There's a lot of headroom. And if your main goal is capacity you could decide to just not run it faster, which will avoid basically all the extra heat.
- Robotbeat 4y agoIndeed, the flash write endurance is actually significant higher at higher temperatures (I presume because of greater charge mobility) with modern flash. But data retention, naturally, gets shorter at high temperatures and quite a bit longer at low temperatures, and it can vary by orders of magnitude between temperature extremes. Again, I think due to the charge mobility effect.
- kasabali 4y agoThat's from controller chips.
- dale_glass 4y agoThere was a paper a while back that promised a healing process for flash: https://www.zdnet.com/article/self-healing-flash-for-infinite-life/ https://www.zdnet.com/article/self-healing-flash-for-infinit... I have no idea what happened to that though, because it sounded extremely promising.
- kasabali 4y agoProbably they're more interested in selling you new flash.
- chx 4y agoThis is TLC flash, don't worry.
- userbinator 4y agoEven the reads aren't truly nondestructive --- look up "read disturb".
- rasz 4y ago> write-once, read many but not too many, read disturb is also a NAND problem.
- yread 4y agoI would actually love that. I need fast random access to data that never changes. SSDs are an overkill and too expensive, HDDs are too slow