9 ms·
Making holes without an electric drill
- d4a 4y agoI would have liked some pictures to know what I'm reading about
- amelius 4y agoYes, this would have been more satisfying and faster to consume as a youtube video.
- bussierem 4y agoI recommend the Primitive Technology channel for this! He uses almost all of these to some extent.
- tootie 4y agoPrimitive Technology on YT has built some of these tools and cut holes with hot coals. https://youtube.com/playlist?list=PLGnWLXjIDnpBancnnrjhxvvXuICsQEJu0 https://youtube.com/playlist?list=PLGnWLXjIDnpBancnnrjhxvvXu...
- Wistar 4y agoAnd punch/punch press, laser, waterjet, plasma cutter, mill, projectile and, of course, shaped charge.
- hef19898 4y agoPlus one for the shaped charge! Waterjets are pretty cool so...
- walterbell 4y agoApplied Science made an experimental (dangerous) waterjet abrasive cutter from a modified pressure washer, https://www.youtube.com/watch?v=Lg__B6Ca3jc https://www.youtube.com/watch?v=Lg__B6Ca3jc
- deleted 4y ago[deleted]
- bell-cot 4y agoThis being HN, I really expected more how to by Randall Munroe sorts of answers. (BTW, you forgot the railgun, nano-sized black hole, antimatter beam, and trained termite "drill squad".)
- nyanpasu64 4y agoElectrical discharge milling is so cool, but expensive (tens of thousands of dollars for a machine). It's got to be the most overkill and surgical way to drill out stripped screws though.
- Wistar 4y agoOops. I forgot about EDM. Should have remembered as I have had EDM stuff done, although a long time ago.
- formerly_proven 4y agoArticle says you can't plunge with a jigsaw, but you can... not pretty but does work.
- falcolas 4y agoIt also takes a bit of skill and gumption, but yeah, its doable. You tip the saw forward on its table so the blade is above the wood, hold down the “Go” button, and slowly lean the jigsaw back towards flat. It is important that the jigsaw’s table is in solid contact with the wood the, erm, hole time.
- jfk13 4y agoI can vouch for the fact that this works, though I'd consider it something of a last resort.
- swayvil 4y agoWhatever happened to cutting with a tuned laser? I heard about it a decade ago. A laser tuned to the resonant frequency of skin. The protein or whatever. Low power, with no burning, no heat damage. Melted right through, cleanly. Unravelled those little molecules. A wonderful cutting device. And maybe you could match a laser to any material. Wood? Glass? A very clean cut. Maybe even safer.
- jfim 4y agoAs far as I know, most laser cutters available to hobbyists for cutting wood are either diode or CO2 based, and both have a risk of setting the wood on fire, as well as generate a fair amount of smoke and combustion gases. For cutting holes into wood as a hobbyist, a CNC machine with the appropriate tool will give far superior output for the purpose of making holes in wood.
- Kinnard 4y ago^^
- Gunax 4y agoI like that it's extensive, but a bit too extensive to answer the original question: what is the replacement for an electric drill? The standard crank drill is clearly the alternative [1]. Most home users should not purchase an electric drill IMO. They dont need it. It will likely never drill more than a few dozen holes. [1] https://www.amazon.com/Frylr-Speedy-Powerful-Manual-1-5MM-10MM/dp/B078SQTLMM https://www.amazon.com/Frylr-Speedy-Powerful-Manual-1-5MM-10...
- thehappypm 4y agoThat’s as expensive as an extremely low end electric drill.
- mauvehaus 4y agoAs a bonus, it's much slower, which leads to fewer fuckups at the ends of projects. They are really only good up to about 1/4" holes though. If you get one with multiple speeds, you can go to 3/8", but you're really much better off with a brace and some auger bits at that point. Auger bits are conveniently sized by the 1/16" down to 1/4" in the US, and have been for over a century. In all seriousness though, an eggbeater drill will last forever. Mine are probably 70 years old or older. Ditto my brace. Good luck finding batteries for any electric cordless drill in 20 years, never mind a cheap one.
- jamiek88 4y agoJust going through this now. Everything is lithium now and can’t find reasonably priced OEM batteries for my drill I bought in 2007.
- evan_ 4y agoDepending on your battery platform you might be able to find an adapter. DeWalt for instance sells an adapter to use their newer 20v lithium batteries on tools built for their older 18v platform: https://a.co/d/73x4MGy https://a.co/d/73x4MGy You can also find third-party adapters to convert between basically any two battery platforms.
- avar 4y agoThe router instructions make no sense to me. Why plunge a router and then switch to a jigsaw to make a large circular hole in a sheet of plywood? Just move the router around instead. You can use a bit that can follow a template to make this as accurate as you'd like, but freehand is usually sufficient. Also: A notable omission in the "other powertools" section is the angle grinder. Both to "saw" a hole, and by attaching a drill chuck to the grinder. At that point it's basically an electric drill with another form factor.
- falcolas 4y agoThe router won’t cut as quickly, especially with thicker materials. You absolutely can, though.
- bombcar 4y agoThis is the correct answer, and router bits are quite the expensive piece of equipment; jigsaw blades are cheap. https://www.rockler.com/power-tools/routers/router-bits https://www.rockler.com/power-tools/routers/router-bits
- avar 4y agoYou can splurge on router bits, but I've also got a set of perfectly usable 12mm bits from AliExpress that I've even used for hardwood, and which will be just fine for any plywood. You can also spend a lot of money on drill bits if you're seeking perfection over the perfectly adequate.
- falcolas 4y agoSo, those router bits from Ali are likely to have a few concerns: - Lower quality metal, meaning they need to be sharpened more often. - Looser tolerances, more vibration for you/the router to compensate for, and a lower quality finish. - Consistency between blades will be low. Perfectly adequate is ok for low frequency and low expectations, but not for anyone expecting high output or high expectations.
- EnKopVand 4y agoI don’t really like electrical appliances. I use a manual whisk (Google translate turns hjulpisker into auxiliary whisk) for everything “whisky” even though we have a vitamix thing that cost more than my MacBook Air. So I’m an idiot like that, and you might expect me to use a manual drill (I guess it would be auxiliary drill if Google translate is right), and until I bought a house you would have been right. Now I own both an electrical drill and a drill hammer. So while my whipped cream still takes a few minutes more than an electro mixer you won’t ever find me drilling a hole without a power tool. It’s just not worth it. Great article though, it’s nice to see all the options covered.
- EForEndeavour 4y agoHow dumb of an idea would it be to somehow attach your electric drill to your manual whisk handle?
- EnKopVand 4y agoThe whisk actually works like the electric ones. It has two “whisks” and then it has some sort of wheel that you turn around to make them spin. It’s really astonishing how something so simple can challenge my English so much lol. But you can get drills that work in a similar fashion, I know because we had them at carpentry class when I was in what we call folkeskolen, so maybe the school that you go to before high school?
- bombcar 4y agoI've done basically that but with a beater; you have to run the drill quite slow but it works.
- evan_ 4y agoThere’s an episode of Good Eats where Alton Brown chucks a cordless drill onto a pepper grinder to pretty good effect.
- mcronce 4y agoI saw that episode and imitated with my Milwaukee cordless drill. It's very very good.
- deleted 4y ago[deleted]
- deleted 4y ago[deleted]
- nimbius 4y agoweird hn strikes again. I learned about most of this stuff in trade tech school and I think its really neat people on this site are interested. I use rotary impact drivers and drill presses all day long at work. there's no shame. gimlets see a lot of use in jewelry and my foreman once said you never sharpen them because they're generally case hardened and snap too easily. they're very fine instruments in the hand. for you drill owners out there the best advice I can offer is always punch your holes first, always wear safety glasses and learn to sharpen your bits.
- eropple 4y ago> always punch your holes first Definitely. And this is why, if you've got the money, why a drill+driver set is pretty handy - you drill with the drill, then you drive the screw with the impact driver, and you haven't had to mess around with switching your bits. (I have two of each in the shop, because sometimes I need a #10 T20 and a #8 T15 screw at the same time, and that means separate drills and separate drivers.)
- insaneirish 4y ago> always punch your holes first Anytime I'm drilling a lot of holes, screwing a lot of screws, or screwing any number of screws but with a high accuracy requirement, I pre-drill with a tapered bit (example: https://www.amazon.com/FTG-USA-Replacement-Countersink-Tapered/dp/B078JBCXL9/ref=pd_lpo_2?pd_rd_i=B078JBCXL9&psc=1 https://www.amazon.com/FTG-USA-Replacement-Countersink-Taper...). They're typically used with countersink bits, but that's not how I use them most often. They're just really good at nailing a hole location quickly and accurately. And for things like framing, they are good at setting pilots for toe screws which can sometimes otherwise be annoying to do.
- eropple 4y agoThat's an interesting hack. I typically use brad-point bits instead because I've got multiple indexes of them.
- walterbell 4y agoSome non-generic widgets: PB Swiss center punch with tungsten carbide point for hard metals, https://www.pbswisstools.com/en/tools/quality-hand-tools/striking-tools/product/pb-7121 https://www.pbswisstools.com/en/tools/quality-hand-tools/str... YG-1 (South Korea) spiral flute tap, evacuates metal chips, useful for custom device enclosures, https://www.amazon.com/gp/product/B00F8T4ST2/ https://www.amazon.com/gp/product/B00F8T4ST2/ & https://yg1usa.com/ https://yg1usa.com/ Norseman bits (USA), http://norsemandrill.com/ http://norsemandrill.com/
- sbierwagen 4y ago>PB Swiss center punch with tungsten carbide point for hard metals I feel like anyone drilling stuff that's harder than 40 HRC, or worse yet, 40+ HRC stainless steel; will be worrying more about bit choice or feeds and speeds than choice of center punch.
- skybrian 4y agoI wonder what's good for making holes in plastic? I've had bad luck using drills since it can melt the plastic and gunk up the bit.
- bombcar 4y agoOften for weird materials you either need really low speed or really high speed. https://ruko.shop/blogs/ruko-shop-blog/which-drill-bits-to-use-for-plastic https://ruko.shop/blogs/ruko-shop-blog/which-drill-bits-to-u...
- TheRealWatson 4y agoWhich type of drill bits you tried? There are drill bits made specifically for plastics.
- analog31 4y agoI have had great results with a Unibit... as in, 1000's of holes for a small gadget that I make for my side business. They have zero rake angle, so they don't pull through thin sheet material. Keep them as sharp as possible to minimize heating. The bit that I use for plastic isn't allowed to touch metal. If coolant is needed, plain water works just fine. Some oils will craze plastic. Brad point bits also work well. If you're not doing production work, just be patient and proceed slowly to avoid heat buildup.
- deleted 4y ago[deleted]
- jasonhansel 4y agoI'm surprised that the article doesn't recommend an ordinary hand drill, like the one Fiskars makes, for creating pilot holes. Are push drills generally considered superior?
- analog31 4y agoI have both: A Stanley "egg beater" drill, and an old Yankee push drill. Each has its advantages: The Stanley has a conventional chuck, and can take any size drill, including a Unibit. It produces a smoother hole and is more controlled when you break through the other side of sheet material. It's a tad more expensive than the Fiskars, but looks to be a lot better made. The Yankee only requires one hand, so you can hold the workpiece with the other, hang onto a ladder, etc. But it produces a rougher hole, and will break through quite abruptly. But for something like a pilot hole for a screw, which doesn't need super precision anyway, it's fine. Both are super convenient: Lightweight, compact, don't need any forethought to make sure they're charged, no worry if they get rained on. If I had to have just one, it would be the Stanley, but the Yankee was given to me by a friend who collects old hand tools. Like the above poster, I greatly prefer hand tools when I can get away with using them.
- kstenerud 4y agoI've used most of those alternatives in my life. Here is my advice: The best way to avoid being caught without the right drill bit is to have MULTIPLE sets. They're dirt cheap and never go bad (unless you leave them exposed to the weather). Get a spare drill while you're at it. Hell, get two; they're dirt cheap. All this fiddling about with inferior or not-quite-right-for-the-job tools makes for great HN reading, but is rather pointless in the real world. Also: Drill a pilot hole first. The only cases where I'd say older is better would be places where the quality has gone so far downhill that it impacts the work. Things like: - nails - screws - chisels - axes - knives (although there are still plenty of good knife makers today) - heavy equipment like drill presses, lathes, pipe benders, etc
- walterbell 4y agoWhere would one find older screws? What do you think of SPAX and GRK screws?
- eropple 4y agoNot OP, but modern screws, bought from reputable suppliers, are absolutely fine. SPAX and GRK are extremely strong in both dimensions; they won't snap when you haul on them with an impact drill and the holding force is extremely...hold-y. If you buy wood screws on Amazon, maybe they have thinner-than-spec threads and get weird. Maybe. I've done it (I can't get, say, oval-head slotted brass screws here too easily, so the internet's the option) and never had problems when I've drilled pilot holes and countersunk them correctly, even on fairly large pieces.
- deleted 4y ago[deleted]
- max_entropy 4y agoDon't forget the pin vise!
- deleted 4y ago[deleted]
- eternityforest 4y agoI was about to write this off as a case of "If you do DIY you probably have a drill", but then I remembered that hand tools do have a weight advantage and having some way to drill in a small field repair kit wouldn't be a bad thing at all. Although, perhaps a micro rotary tool would be better in some cases. I still don't understand the people that say gand drills are more convenient for just one or two drills, unless they are comparing to a corded drill. I don't think I've ever actually used a corded drill though.