7 ms·
Shellac
- brodouevencode 5y agoAmateur woodworker here. Shellac is relatively easy to work with, but hard as nails when it dries. It’s a great tool in the tool belt.
- moistly 5y agoMy love: nitrocellulose lacquer over shellac over oil. Pops the grain like magic.
- exDM69 5y agoNothing wrong with that but a damaged nitro surface is difficult to fix. On the other hand it's probably more durable than just shellac.
- moistly 5y agoDead easy to fix… if you have some nitrocellulose lacquer. Alas, it is increasingly difficult to find.
- kaydub 5y agoAnywhere I can read about nitrocellulose lacquer? How is it applied?
- moistly 5y agoI imagine google is your friend for researching lacquer. I apply lacquer using a quality natural bristle brush; it can also be sprayed, but it is very flammable and requires a proper paint booth setup. Also, the fumes are very poisonous, so proper masking and ventilation is a requirement. I apply boiled linseed oil to "pop" the grain, then a layer of clear shellac, then several layers of lacquer. Every few layers I do use a scraper (facedown) to knock down the dust irregularities. Both the shellac and lacquer dry extremely quickly. After the final coat I use the scraper and then 0000 steel wool to give a fine satin finish. Lacquer (and shellac) damage is easily fixed by applying more. The fresh coating melts the old; the only hitch is in blending out the edges. I find lacquer much easier to work with than the newfangled concoctions. Easier to apply smoothly, easier to knock down the dust, easier to polish with steel wool, and easier to repair any mistakes. Not nearly as durable, though, and a much greater health hazard while applying.
- exDM69 5y agoA very nice property of shellac is that is easy to repair and difficult to screw up. I recently restored a large cupboard that would've been a whole lot of nasty chemicals and sanding had it used modern film finish lacquer. Instead, it being shellac, it was a matter of a quick clean up for the worst scratches, followed by applying more shellac coats and blending it in with the old finish. It's also very pleasant to work with on new projects and the results are awesome. With the right kind of wavy grained wood it can have a three dimensional hologram-like chatoyance, almost like a gemstone.
- dvh 5y agoI've recently had my first experience with shellac. Bought 10g of red flakes for ~$2, dissolved it in alcohol, applied 10 layers or so. Despite being red it has some yellowness to it, smells absolutely delicious, it's relatively easy to scratch with nail (although this might be because I used pine). Dries in about day. Very glossy. I don't think it's good for things that are handled manually like a guitar. Eventually I decided not to use it and went for EN 71.3 paint/stain that is specifically designed for toys.
- thisiscorrect 5y agoI thought guitars typically get a French polish which does use shellac.
- exDM69 5y agoSome guitars do but it's not common. Nitrocellulose lacquer was common in the 20th century and linseed oil with natural resins before that.
- _0ffh 5y agoWhen I hear "nitrocellulose" I quickly get doubts if I'd want to coat my instrument in it. (If it's common I presume it must be safe, more or less, but it sure doesn't inspire much confidence in me.)
- exDM69 5y agoNo, it is not safe, and that is why it is regulated and hard to get in many parts of the world. Afaik the final product is pretty safe but handling the chemicals while working with it needs precautions.
- namibj 5y agoWell, handling the lacquer while (re)coating a guitar would only have the typical solvent issues.
- mongol 5y agoShellac Origins and Manufacture https://youtu.be/lQcQ0yuekZ0 https://youtu.be/lQcQ0yuekZ0
- igammarays 5y ago> Shellac is labeled as GRAS (generally recognized as safe) by the US FDA and is used as glaze for several types of foods, including some fruit, coffee beans, chewing gum, and candy. Examples of candies containing shellac include candy corn, Hershey's Whoppers and Milk Duds, Nestlé's Raisinets and Goobers, Tootsie Roll Industries's Junior Mints and Sugar Babies, Jelly Belly's jelly beans and Mint Cremes, Russell Stover's jelly beans, and several candies by Godiva Chocolatier and Gertrude Hawk. M&M's do not contain shellac.[6] https://www.eatlikenoone.com/shellac-a-candy-ingredient-made-from-bugs.htm https://www.eatlikenoone.com/shellac-a-candy-ingredient-made...
- c2h5oh 5y agoI've just used shellac to make homemade "dykem blue": - 22g of shellac - 4g of gentian violet dye - 500ml of 99% rubbing (isopropyl) alcohol or 95% ethyl alcohol give it a couple of days to dissolve shellac shaking the container once or twice a day. Works like a charm.
- leksak 5y agoI learned a lot about Shellac from the podcast Reasonably Sound (episode: The World Remade). Highly recommended deep dive into the world of vinyl records.
- lvl100 5y agoShellac has uses but for most furnitures, you are better off using precat lacquer. Shellac takes a lot of trial and error to get it right for your specific uses. So I recommend you experiment with it first. For example, denatured alcohol (from big boxes) has diff evaporative properties vs pure ethanol vs rubbing alcohol etc. Same goes for lubricants.
- exDM69 5y agoShellac is really easy to use, and if you get it wrong, it's also easy to rub it off and go back a step. Modern lacquer finishes have lots of nice properties, but it is not as forgiving to use. And it is more difficult to repair.
- mauvehaus 5y agoA couple points of order: 1) I've never heard of anybody using anything other than ethanol for preparing shellac 2) You are unlikely to encounter pure ethanol outside of a lab. Ethanol can only be distilled to about 95%. Removing the remaining water involves somewhat more exotic processes (I'm a furniture maker, not a chemist) As for precat and other modern finishes vs shellac and other historic finishes, an excellent rule of thumb is that the more durable a finish is, the harder it is to repair or restore. Shellac, wax finishes, drying oil finishes, oil/varnish blend finishes, and soap finishes are all pretty repairable. They wouldn't be my pick for a dining room table for most people, but they're pretty easily renewable under normal use for most other applications.
- lvl100 5y agoYou never heard of anyone using shellac with denatured alcohol from big boxes? Very interesting.
- mauvehaus 5y agoDenatured is primarily ethanol and is what most people use, to my knowledge. People have also been known to use 190 proof grain alcohol from the liquor store, which is taxed differently (it costs a lot more) in the US because it can be consumed by humans safely. Rubbing alcohol is isopropyl alcohol, which I've never heard of anybody using. I'm not claiming that it won't work, but I've not tried it or heard of it.
- franky47 5y agoAs a side note: Japanning, as mentionned in the first image's caption, is another of history's fascinating and forgotten finishes. It was used to finish the Ford model T, Singer sawing machines, and cast iron hand planes, among other things. Learning how to make it again (from asphaltum powder, boiled linseed oil and turpentine) to restore old hand tools is quite the rabbit hole. If you're looking for a good primer, aPlaneLife has a series of video talks [1] on the matter. [1] Part 1: https://www.youtube.com/watch?v=9NlltN3twUA https://www.youtube.com/watch?v=9NlltN3twUA Part 2: https://www.youtube.com/watch?v=PzXmtzmKvKc https://www.youtube.com/watch?v=PzXmtzmKvKc Part 3: https://www.youtube.com/watch?v=DEC5SyenFcE https://www.youtube.com/watch?v=DEC5SyenFcE
- jdgoesmarching 5y agoAs someone looking to restore a hand plane, I’m going to pretend I didn’t see this and jump straight to my plan of using engine paint.
- hilbert42 5y agoThat's fine. Your plane won't work any less efficiently and it'll be ready/dry overnight unlike we crazy aspheltum users who require at least week for it to cure. If using engine paint, you can have choice of colors which we're denied. My Record No 7 came out of the box brand new and it's a light sky blue. I've also a Stanley No 4 clone from some European manufacturer and it's original color is a Ferrari red. Looks good too.
- hilbert42 5y agoThanks for that, I have about a dozen planes to do that I've been putting off for years and I've never taken the time to properly research the best place to buy the asphaltum. Now I have the info all in one location.
- mauvehaus 5y agoI haven't watched the videos yet, but I can tell you that if you use turpentine, it stinks like hell and is best done with the windows open, the doors to the rest of the house closed, and anybody you share your house with out of town. Mine also took a lot longer in the oven to fully cure than the information I had at the time suggested it would. It is an absolutely beautiful finish though.
- novosel 5y agoIt was (and still is) widely used in printing industries (transfer ink, lithographic ink), in arts (India ink is basically a black pigment suspended in borax solution of shellac), in paints (addition of shellac to acrylic water-based paint improves the performance), production of music records, in watch making (as a thermoplastic glue), in paper production as a calendering agent ...
- geon 5y agoClickspring has a great video on the application of french polish; https://youtu.be/vFXsJNO3qsI https://youtu.be/vFXsJNO3qsI
- jasonhansel 5y agoOne interesting historical fact: the earliest plastics were invented in part to create a cheaper alternative to shellac, which served many of the purposes that synthetic plastics do now.
- sydthrowaway 5y agoEarly humans were quite resourceful. Wonder how they decided this would be a useful material