3 ms·
The article seems to be mostly about voltages and plugs/sockets that the consumer will see at the outlets throughout their home. It's interesting to look a lit
by tzs 5y ago
The article seems to be mostly about voltages and plugs/sockets that the consumer will see at the outlets throughout their home.
It's interesting to look a little beyond that. Most of the places that offer 230 V at their outlets seem to be distributing power in the neighborhoods using a 3 phase 230 V system. Individual houses are wired to one phase of that.
In the US, distribution throughout a neighborhood is typically 15 kV. There is a 240 V center tapped step down transformer for each house. The normal outlets in the house are wired across half the transformer, giving 120 V. Ovens, water heaters, dryers, EV chargers, air conditioners, etc get wired across the full transformer giving 240 V.
There was an interesting comparison of the two approaches in this Quora answer that turned up in my Quora digest mailing two days ago [1]. (Not sure if the link will work without a Quora account).
[1] https://qr.ae/pGosj7 https://qr.ae/pGosj7
- alkonaut 5y ago> Individual houses are wired to one phase of that. Or all 3. I thought this was most common. 3x20A (or 16 or 25) 240V is the standard for detached houses in parts of Northern Europe at least.
- Scoundreller 5y ago> There is a 240 V center tapped step down transformer for each house. Maybe in rural areas, but in (sub)urban areas, you'll have a... ?node? step-down transformer serving many homes. > The normal outlets in the house are wired across half the transformer, giving 120 V Would add that homes usually balance this, so half of 120V circuits will be wired to one phase, and half to the other. So sometimes you get power failures where half the house loses power. Also means installing power-line networking may only work (well) when they're on the same half of circuits of the house, unless you add a capacitor between the two sides to bridge the gap for high frequencies. Or turn on a 240V appliance to bridge the two sides together.
- masklinn 5y ago> Individual houses are wired to one phase of that. In many countries houses get wired to all three phases and the phases get split up afterwards, sometimes with a few 3-phase plugs available for high-power applications.
- nwallin 5y agoIt's also common in the US for neighborhoods to have 240V 3 phase, and for a neighborhood to have a common neutral. Each house gets the neutral and 2 of the hots. Hot to neutral gives 120V, hot to hot gives 208V. (240*sin(120 degrees)) The result is that the high voltage appliances need to support both 240V and 208V. Most appliances just design for 240V and test to ensure they don't break at 208V, and just give reduced power at 208V. Which is often fine, but a 208V stovetop is a pretty miserable experience.
- sopooneo 5y agoInteresting. Thank you. I always assumed they were 180° out of phase.
- p1mrx 5y agoYou could run a heating element at full power on 208V by adding a center tap connected to neutral. For something fancy like an EV charger, you would probably need dual 120V AC/DC converters, which isn't worth the effort, given that constant-current loads run at 86% power (208/240), compared to resistive loads at 75% power (208/240 squared).
- qwerty456127 5y ago> The normal outlets in the house are wired across half the transformer, giving 120 V. Ovens, water heaters, dryers, EV chargers, air conditioners, etc get wired across the full transformer giving 240 V. Why not just give the 120 V up and go full 240 V in every outlet?
- throw0101a 5y ago> Why not just give the 120 V up and go full 240 V in every outlet? No one feels it's worth the effort. You'd need two sets of plugs in every home and redesign a whole bunch of appliances and sell both types during the change over period, which could last decades.
- selfhoster11 5y agoMost appliances that draw less than a kilowatt of energy are capable of switching to 240V or 120V as needed, some even automatically.
- qwerty456127 5y agoIf so, then I would prefer to make all the outlets in my hypothetical American home 240V. Why don't actual Americans do?
- selfhoster11 5y agoBecause that doesn't account for the 20% of random devices that aren't directly 240V capable. It's not as plug and play as it could be.