15 ms·
Guerrilla guide to CNC machining, mold making, and resin casting (2015)
- SavantIdiot 5y agoWow, really short section on gears. But there is so much to cover I can't blame it. If you've ever dabbled in robotics, you've probably found it is an enormous step function from kits like Actobotix [1] to custom parts. It is infinitely easier to use kits or frameworks that have already taken a LOT of the guesswork out of gears, linkages, motors, compatibility, etc. Especially gears, they are an enormous pain in the ass to source online, and even when you find the right gears, you still need hubs and axles, and then you hit min volume issues, non retail sales, overseas... I even have access to a phenomenal machine shop, but what I don't have is a machinist. (There are a few that mill around (pun intended) but they are mostly introverted decent guys that don't really want to help a noob.) [1] https://www.servocity.com/actobotics/ https://www.servocity.com/actobotics/
- paulgerhardt 5y agoHaving spent a million dollars making gears, my ultimate conclusion is it’s the sort of thing you machine from brass gear stock unless you want to spend a million dollars.
- SavantIdiot 5y agoFor what 99.99% of makers are doing, Actobotix is fine. But if you want to make your own fancy differential or a hypercycloid linear translator, yeah, you're gonna have to do it yourself.
- failwhaleshark 5y agoWhat dimensional scales, materials, turn-around, volume, and/or processing? Breaking tools and getting G-code just right seem like the perpetual headaches of modern machinists. Other than occasionally being bitten by a bitchy blade-like chip begging to fillet your grizzled knuckles one last time before banishment from the bench to the backyard becycling bile of betal bits. If electricity were cheap (or the electric meter rewindable), would multiple beam concurrent FDM be a consideration if the materials and metallurgical characteristics allowed it? I think at some point, it's easier to print complex shapes additively than machine them subtractively, and that needs to be part of structured cost decision-analysis for manufacturing.
- jrockway 5y agoI think if you want to make one or two custom gears, you just manually mill them. CNC involves the usual programming tradeoffs -- you spend a ton of time writing and debugging the program, and then you can run the program a million times to make a million parts. For making one part, it's not clear that it's worth the overhead -- just set up your stock on a dividing plate and use a gear cutting tool to cut the teeth. If when you're turning the handwheels the machine makes an unpleasant noise or it feels like you're going to break the tool, stop turning the handwheels and use your brain's built in AI algorithm to develop a new plan ;)
- ganzuul 5y agoUsually a short run of a new part doesn't take more than half a day to set up on a CNC. If you are making thousands of parts to run unmanned you might have to add another day to it.
- failwhaleshark 5y agoWatch AvEs vijeos. Problems. No problems. After they are fixed by the meat confusor. They are solved. Your tool in a vise.
- chrisseaton 5y agoWhat is 'brass gear stock' as opposed to normal brass?
- reportingsjr 5y agogear stock is basically a gear that's really, really long so you can just cut off whatever width gear you need. Similar to bar stock, which is just rods of metal, but in gear shape.
- auxym 5y agoSomething like this: http://shop.sdp-si.com/catalog/?cid=p593 http://shop.sdp-si.com/catalog/?cid=p593 So you can decide on a module/PA, buy a few diameters then cut off the required face width you need and machine the bore as needed.
- jalgos_eminator 5y agoIn case anyone wanted an approachable introduction to machining your own gears, there's a This Old Tony video about it: https://www.youtube.com/watch?v=Q-XOM4E4RZQ https://www.youtube.com/watch?v=Q-XOM4E4RZQ
- mikewarot 5y agoI spent 5 years making gears in a job shop. I did a cursory look through the section on gears, it seemed adequate for someone who is doing a hobby project. I'll watch this thread and answer any questions you might have.
- Scene_Cast2 5y agoWould you know what type of approaches and machinery is needed for relatively loose tolerance / low load helical gears? If going the CNC route, do I need full 5 axis and specialized end mills? Even with regular involute straight gears, there's a bunch of ways one could manufacture one, and I'm out of my depth here.
- ganzuul 5y agoThe industrial strength version: https://m.youtube.com/watch?v=EefFxEGVbWo https://m.youtube.com/watch?v=EefFxEGVbWo I made sprockets with an endmill and a simple macro on a C-axis lathe. Worked just fine since the tolerance on those is very forgiving. In principle you could make a helical gear as a multi-start thread. I'll have to test it once I have the machine free an afternoon.
- jjk166 5y agoIt's way easier to start with components you can readily source and design your system to use them than to make custom components. If your robot isn't going to space, the benefits of custom components will not be worth it.
- dls2016 5y agoTimely… spent the day machining a mould for a foam windscreen.
- mod 5y agoCan you elaborate? I'm having a hard time imagining what a foam windscreen is, or what its purpose is. Is it just like a motorcycle windscreen that you don't need to see through?
- dugditches 5y agoI think they're referring to a microphone 'windscreen'.
- dls2016 5y agoYes, trying to mould a microphone windscreen for low frequency applications.
- tmaly 5y agoI would like to try resin casting to make some wall on-lays. Has anyone on HN tried making molds for detailed castings?
- dugditches 5y agoMight be better with just 3D printing, body filler and spray paint.
- ArtDev 5y agoI bought a similar kit from Smooth-On to make casting of Warhammer 40k miniatures. It was amazed at the detail and accuracy of what I created! The secret was using a back massager to vibrate the table to get out the bubbles! This is the kit I originally bought: https://www.smooth-on.com/products/pourable-silicone-starter-kit/ https://www.smooth-on.com/products/pourable-silicone-starter...
- haram_masala 5y agoI’ve done it for making fake ancient coins - like another responder, I used a Smooth-On kit and it couldn’t have been easier. Though I was casting bismuth alloy rather than resin. One tip, be sure to dust the mold with talc to allow air to escape. Also the vibration table tip sounds good.
- grae_QED 5y agoArtisan Alliance made a couple of very good videos on high detail resin casting with silicone molds [1]. They focus on mechanical keyboard keycaps, but the same ideas apply to many other things. [1] https://www.youtube.com/watch?v=5cnLJm0kMdg https://www.youtube.com/watch?v=5cnLJm0kMdg
- s5300 5y agoI really think that every well rounded person/STEM academic should at one point in their life (hopefully sooner rather than later) expose themselves to some hands on machining... like, even just a few hours on an old decrepit mill/lathe. I feel like the foundations of the industrial revolution (speaking within the US) are... very much forgotten/taken for granted given the fact the near entirety of our modern life and comforts exist because of it. There's fortunately a ton of great, readily available content on YouTube/elsewhere that's sprung up in the past 10 or so years you could just watch, but actually machining is such a cathartic experience... at least when you're in a position to do so that isn't in a grimy ass factory/warehouse with somebody yelling at you to push out more operations than is humanly possible, haha.
- prpl 5y agoMost working undergrads (RAs) in the physics department at my university had been trained in the Physics department machine shop at some point in time, so it was common for them. Probably the only program outside ME where that was true
- R0b0t1 5y agoNot sure this is normal. Have heard stories of physics department needing to contract to the engineer's union, and people getting in trouble for screwing together a wooden box.
- jbay808 5y agoThat's the scenario that I'd call abnormal! What a nightmare!
- R0b0t1 5y agoSeems fairly normal from what I can tell. Issues like needing everything to be vetted my a mechanical/civil/electrical engineer, depending on what it is, and not being able to machine your own parts and needing to let the university machine shop bill time.
- sarak12070 5y agoThe Rock’s daily Diet & Workout Plan Be strong and healthy http://healthwithbeauty.xyz/2021/06/26/the-rocks-daily-diet-workout-plan/ http://healthwithbeauty.xyz/2021/06/26/the-rocks-daily-diet-... ultra bouquet patch mask Also there is 18% discount offer so avail from Amazon https://topsaleproductsonline.blogspot.com/2021/06/ultra-bouquet-patch-mask-with-discount.html https://topsaleproductsonline.blogspot.com/2021/06/ultra-bou... Interesting facts about frilled coquette https://www.interestingnews.club/2021/06/interesting-facts-about-frilled-coquette.html https://www.interestingnews.club/2021/06/interesting-facts-a...
- 71a54xd 5y agoFun fact, all CNC machines sold in the United States with more than 5 axes of travel have to be registered with the ATF and have a permanently attached GPS tracking unit. This is even true if you have zero intention of using your CNC to manufacture anything reminiscent of a firearm or firearm component. This is why it's common to see 4.5 axis CNC machines or a plethora of "upgrades" that grant 5 axis capability post purchase.
- r3trohack3r 5y agoFascinating. I searched “ATF register 5 axis cnc” and came up dry. Do you have a reference?
- ff-- 5y agoThat's not true. Machines with enough axes to be used in firearm or aerospace machining are subject to export controls, though.
- Turing_Machine 5y agoYou can make firearms with bog-standard lathes and milling machines.
- R0b0t1 5y agoShhh.
- throwaway2048 5y agoyou don't need a 5 axis milling machine to build a firearm, even a modern one like an M4
- canadianfella 5y agoI don’t believe you.
- GravitasFailure 5y ago
- CNCisDenied 5y agoI was considering last week to pick up CNC machining but now I've lost all interest. It sounds very primitive and intersectional. dang, you have trolls.
- imtringued 5y agoThere is nothing more primitive than a robot that doesn't even know its own position and only follows a program with the hope that it works. (assuming a hobby CNC machine without servos).
- contingencies 5y agoYou just described most motor vehicles: mobile death traps.
- axegon_ 5y agoOne thing to note when it comes to resin casting and cnc is the 3d printing evolution since 2015. The amount of detail you can get from an inexpensive 3d printer these days is astonishing and it seems like less far less messy than a cnc. Not that long ago I got a resin-based 3d printer and I was blown away by the prescision. That said, for me at least, there is a big problem in that entire field - the third point - "Mastering CAD and CAM". To put it lightly I really suck at it. I am using Blender(100% linux user) and having to switch between layout modeling and sculpting(etc.) often puts me in a Hulk mode rage. I can't find a pattern in the menus or modes and everything I try to do ends up being 2 hours of googling and youtube tutorials. Which I reckon is me being too used to cli-tools and hardly ever going outside the cli world(if it weren't for browsers and the modern web which cannot work without js, I'd have probably removed my desktop environment altogether).
- mmaunder 5y agoI understand you use open source, but Fusion 360 really is a game changer. The CAD to CAM workflows are easy and intuitive once you learn the basics. Blender is designed to be a lot of things to a lot of people and I can see how that would be extremely frustrating. Yes Fusion isn’t cheap, but it’s very worthwhile IMO.
- ganzuul 5y agoAutodesk is unfortunately doing exactly what one can expect Autodesk to do. As soon as Fusion 360 meets a milestone they add new ways to monetize their users. TBH I can't recommend it for anyone outside US jurisdiction because of how the company is managed.
- axegon_ 5y agoNo, I'm not full on RMS here, if there's a proprietary software that I could use and I can use it under linux, god speed. Sadly adobe and autodesk are reluctant to add more support, despite the demand.
- skybrian 5y agoI'm liking Onshape for CAD. There's a learning curve, but it seems logical in a geometric puzzle-solving sense. I read a bit about resin-based 3D printing (stereolithography). The amount of detail looks impressive but it sounds expensive and messy due to the toxic chemicals and fumes. How do you deal with that?
- Yenrabbit 5y agoI remember avidly reading this whole thing when it came out (and a lot of the rest of the blog) despite not having a CNC myself. Always great to see someone sharing knowledge from their own deep interest in a topic.