4 ms·
Battery parts can be recycled without crushing or melting
- Syonyk 6y agoInteresting, but probably "of limited use to useless" long term, because batteries don't come apart nicely without, at a minimum, high risks of shorting them out and thermal runaways. For the typical cylindrical cells, the "jelly roll" is squeezed in quite tightly (this reduces internal resistance by squeezing the bits tightly together and optimizes capacity per cell), and then the bits tend to swell a bit in use. This is one of the advantages of a cylindrical cell - those stresses turn into tension stresses around the circumference and the cell doesn't actually swell like prismatic cells. But getting the bits out, intact, without shorting something out? Good luck. https://doi.org/10.1002/cssc.202100629 https://doi.org/10.1002/cssc.202100629 is the link to the article, but I don't have access without paying. If anyone finds it, I'd love to read it to see what they've done, though!
- giuliomagnifico 6y agoI think this technique can applied only on batteries already made to be recycled in this way, but is a good pint for the future industries “By reusing the structures of batteries we can avoid a lot of the labour that is common in recycling and potentially save energy at the same time. We believe that the method could help companies that are developing industrial recycling,” Kallio says.
- dehrmann 6y ago> because batteries don't come apart nicely without, at a minimum, high risks of shorting them out and thermal runaways. Is there a way to speed up self-discharge? Or maybe manufacture batteries in a way such that they can be easily discharged over a ~day, bypassing any circuits limiting the maximum discharge? The way they're packaged sounds harder to mitigate, though.
- Syonyk 6y agoShort 'em through a resistor, it's easy enough to fully discharge them. You damage them if they're left discharged for too long, but for short periods, it might be fine. Unfortunately, they also tend to swell when fully discharged. "Disassembling lithium batteries without destroying them or your workshop" is depressingly hard.
- zackees 6y agoLikely works for larger EV type batteries though..?
- cbmuser 6y agoUsed nuclear fuel can be recycled by 95%, try to beat that.
- dv_dt 6y agoLead acid batteries?
- tonyedgecombe 6y agoAre the most recycled consumer goods, I seem to remember 97% are recycled.
- _Microft 6y agoWell, this might be true but it is irrelevant with regard to powering electric vehicles, smartphones or other gadgets.
- ketralnis 6y agoUsed baseballs can be recycled by 100%, try to beat that.
- m463 6y agoKeep your elbow up when facing the recycling machine. :)
- londons_explore 6y agoWhy not just grind them up in a vacuum chamber? Both cheap and fireproof. The vacuum pump will collect all the electrolyte, nearly ready to directly reuse. Without electrolyte, the ground up batteries aren't very flammable or dangerous. The rest you can chuck as input into a metal smelter and get back as a battery without too much energy invested.
- deleted 6y ago[deleted]
- amelius 6y agoHeating things up can be prohibitively expensive. Otherwise we could simply heat CO2 until it cracks into C and O2.
- kayodelycaon 6y agoLithium ion batteries have oxygen in them. If you add heat, they will ignite and you will not be able to put them out until you've dumped enough cold water on them to get them below their ignition point.
- Syonyk 6y ago> Why not just grind them up in a vacuum chamber? Because the energy stored in the chemistry of them doesn't care about oxygen and will happily come out in a hurry. Look at some of the videos of a crushed 18650 - they don't get any oxygen in them, but they sure make a nice little firework. The exothermic runaway is totally oxygen independent, and evolves a variety of nasty chemical cocktails out of the electrolyte. Those then tend to ignite when they find oxygen, creating a blowtorch (but less toxic gasses - pick your poison, literally). If I recall properly some papers I read, about half the energy released in a battery runaway is the chemical/electrical energy, and the other half is the chemical breakdown and electrolyte decomposing/burning. So, if you have a 3.7V nominal 100Ah cell, that's 370Wh electrical, and about 740Wh total. Dump that in 15 seconds, and you have a nice ~175kW event to deal with. In any case, it happens quickly enough to be the sort of excitement you want to be upwind of. But grinding batteries is more challenging than it sounds. If they're mostly or fully drained, there shouldn't be enough energy left to get really exciting, but now you need the labor of manually draining each battery before recycling, or you soak them in a salt water bath for a while and deal with the corrosion (salt water is conductive enough to slowly drain a battery without it getting exciting, and it keeps things cool enough that if a cell tries to get exciting, it shouldn't be able to propagate). "Replacing parts without having to go through the smelters" is what the goal is here, it just requires some things to be true about batteries that, to the best of my knowledge, aren't broadly true. Again, I'd love to read the article, though, if anyone has access to it.
- elihu 6y agoPerhaps this could be described as "refurbishing" rather than "recycling"?
- m463 6y agoI can't help but think of this battery rebuild: https://youtu.be/afwO_MZjRjA https://youtu.be/afwO_MZjRjA amazing, really