3 ms·
> So you end up running at 1/10th of the speed your tool could move at to avoid that ... Doesn't that only happen when the controller either doesn't know (or c
by justinclift 6y ago
> So you end up running at 1/10th of the speed your tool could move at to avoid that ...
Doesn't that only happen when the controller either doesn't know (or can't decently handle) the limits for a given machine?
eg if a machine could (say) only accurately (without losing steps) push the spindle at 1000mm/min, with maximum jerk of (say) 0.5
If your controller doesn't know to keep in those limits... it makes sense steps will be lost when going past those limits.
So, seems more like a tuning problem?
That being said, closed loop stepper systems exist, though I haven't (yet) personally tried them.
- PragmaticPulp 6y agoI think he's exaggerating for effect. Properly sized steppers have more than enough margin for rapid movement on hobby machines without losing steps ( Video example at 1000ipm: https://www.instagram.com/p/B1wSmXfnm6C/ https://www.instagram.com/p/B1wSmXfnm6C/ ). Skipped steps are only a problem if the machine is tuned wrong, like you said, or the steppers are too undersized to keep up. People tend to underestimate the strength of common NEMA23 steppers while overestimating the cutting forces they need. Most hobby machines don't have enough rigidity or spindle power to require more than a few pounds of lateral cutting force.
- YZF 6y agoTo be precise, it's not the strength of the stepper, it's the gearing through the screw that converts the torque of the stepper into the force on the tool.
- jacquesm 6y agoAnd that will give you slop which will translate into imprecise workpieces and surfaces that aren't flat.
- PragmaticPulp 6y agoAt the hobby CNC level (what’s being discussed in this article), the rigidity of the machine is far more of an issue. I think your advice is spot-on if someone was designing a 5000lb vertical mill out of steel, but hobbyists building DIY bench top machines face a different set of problems. Hobby level machines are almost always limited by rigidity, not movement motor torque.
- jacquesm 6y agoI've built a whole pile of CNC machinery, both lightweight and heavyweight. If you don't actually care about what you produce, fine, go with open loop steppers. If you want to control a device that produces accurate work products that do not need extensive rework (or to be tossed) then use something with a feedback mechanism. I'm fine with you advocating for steppers for non-contact or drawing work (laser cutters, engraving and so on). But if you care about your tools, you don't want to wait for hours for what should be a small job then add the bit of money for a servo or a hybrid solution, on the total cost of the machine it won't make a lot of difference and the machine will be so much more reliable and faster that you'll end up using it much more frequently. Right tool for the job and all that, bench top CNC with small servos is a very powerful tool in the hobbyists arsenal, and if you scrounge ebay you'll find they can be quite affordable. Note that anything that cuts has a stand-time, and if you move slower or make many passes because you can't really cut then you will end up spending a fortune in tooling which at some point will easily outweigh the price of the feedback mechanism, which automatically compensates for increased load and toolbit wear.
- jacquesm 6y ago> I think he's exaggerating for effect. I wasn't. You'll never make it through your first resonance point without current feedback, and a good stepper driver can easily go into very large multiples of that frequency. Then there is microstepping. > Most hobby machines don't have enough rigidity or spindle power to require more than a few pounds of lateral cutting force. This is true, but a different problem.
- PragmaticPulp 6y agoI think you’re approaching this discussion from a commercial/industrial scale. Hobbyist CNC machines simply don’t have the same issues as large commercial-grade CNC mills. None of the popular hobby CNCs use closed loop motor control. Skipped steps are simply not an issue at this scale.
- numpad0 6y agoI long had dimensional accuracy issue that the whole axes seemed to stretch and contract like 5%, on a cartesian 3D printer, and it just went away after I switched to Servo42B setup. I think it’s microstepping. Steppers with microstepping enabled and controlled by an 8-but micro must be assumed to produce zero holding torque and assumed they always miss a step or two.
- craftinator 6y agoUpgrade the controller. For a hobbyist machine, the ESP32 CNC controller sold on Tindie is well suited to deal with that, and costs ~$35.
- StavrosK 6y agoI made a PCB for an ESP32 CNC controller, if anyone finds it useful: https://gitlab.com/stavros/esp32-cnc https://gitlab.com/stavros/esp32-cnc
- craftinator 6y agoNice! I'll check it out! Here's a link to the one I'm using: https://www.tindie.com/products/33366583/grbl_esp32-cnc-development-board-v41/ https://www.tindie.com/products/33366583/grbl_esp32-cnc-deve... The developer is really responsive, might be worth collaborating since you have put in similar work.
- dekhn 6y agoThere are several newer boards from Bart (including the 6-pack which has some add on modules). Grbl ESP32 is great. Easily the best of the firmwares I've used so far.
- craftinator 6y agoI've been interested in upgrading to his newer boards, but I'm not sure I want the added complexity at the moment. Have you used the generic modular one? If so, how does it compare to the older one I linked to?