4 ms·
USB drives with no phantom load (2018)
- riobard 6y agoDoes any integrated USB hub support per-port power control? I'd like to control a directly-attached USB external hard drive to my Linux box.
- NegativeLatency 6y agoThere are usb cables with inline power/data switches if that helps
- matthewmacleod 6y agoIt’s a difficult thing to find in general. Best list I’ve seen is https://github.com/mvp/uhubctl#compatible-usb-hubs https://github.com/mvp/uhubctl#compatible-usb-hubs
- mikepurvis 6y agoI've delved into this somewhat in an attempt to get some badly-behaved USB cameras under control— the situation is not pretty, especially for USB 3 hubs. I ended up resorting us using a hub that had an internal jumper for disabling bus power, and then just using an external relay to toggle power to the hub itself and all attached devices. This has worked fairly well, though it exposes some other interesting problems which I suspect are deeper issues in the Linux kernel, where "replugging" the same device hundreds of times over the course of days of runtime eventually exhausts some internal resource, causing the port to go completely dead until you unbind/bind the xhci device. Note that if you're not on RPi or some other device with easily usable GPIO to control the relay, you can use any FTDI cable as 4x GPIO, and there are lots of cheap 5V relay breakout boards available.
- jeffbee 6y agoWas curious so I read out HCCPARAMS1 from my Intel xHCI controller and it looks like port power control bit is zero, so no? I think the best you could hope for here is there is some ACPI function you could invoke to power down the whole hub.
- R0b0t1 6y agoSome controllers used to. It's not clear if most still do. There is IOCTL_USB_HUB_CYCLE_PORT in Windows that power cycles a port (https://docs.microsoft.com/en-us/windows-hardware/drivers/ddi/usbioctl/ni-usbioctl-ioctl_usb_hub_cycle_port https://docs.microsoft.com/en-us/windows-hardware/drivers/dd...). My research seems to indicate it doesn't always work. The corresponding utility on Linux has problems on modern hardware but the driver may not be complete. For both operating systems, you can likely use the autosuspend features, but this is gated by the driver (at least on Linux) and may not be able to reset a malfunctioning device. For some reason PCIe and USB lack a way to do a hard reset.
- anonymous_fun 6y agoIn the opensource space, https://github.com/mvp/uhubctl/ https://github.com/mvp/uhubctl/. Commercially($++), Acroname or Cambrionix hubs have a lot of features.
- rwmj 6y agoI found a rare D-Link hub that supports it[1]. However it only supports it for a while. After a few port commands the hub crashes and only a hard "reboot" of the hub will fix it. In effect no. [1] https://rwmj.wordpress.com/2015/10/09/usb-per-port-power-switching/ https://rwmj.wordpress.com/2015/10/09/usb-per-port-power-swi...
- meekrohprocess 6y agoInterestingly, the USB 2.x specification states that a device must not draw more than 500uA (~2.5mW) while it is not being actively addressed by the host. I frequently wonder how many devices actually adhere to that requirement. Probably not many.
- dfox 6y agoThat number is not for devices not actively adressed (whathever that means) but for devices that do not have power profile accepted by host. On the other hand it is slightly unclear how that is meant because that is awfully close to the power required for correct device-side Full speed USB termination network. Thus interpretation that I use is that before enumeration the device as a whole should not draw more than 1mA from VBUS.
- DoofusOfDeath 6y agoNow I'm curious about the legal angle of this. If a company claims their product is "USB compatible", but the product doesn't 100% comply with the detailed technical specification, what's the company's liability? And if the company knew the product didn't strictly meet the USB standard, but marketed the product as "USB compatible" anyway, does that rise to the level of fraud?
- londons_explore 6y ago"We claimed our device met USB, which claimed a max power draw while unenumerated of 1mA, yet our device actually used 500mA. Whoops. How long did you have this device unenumerated for? 1 second each time you plugged it in? Well damages can be calculated then... 1 second * 365 (number of times plugged in per year) * 500mA * 5 volts * 5 years (expected lifespan) * $0.14 ($/kWh electricity)... Total compensation is $0.00014... Would you like a check for that?
- Dylan16807 6y agoThat's one end of the spectrum. The other end is killing a phone's battery in a couple hours.
- drjasonharrison 6y ago@pabs3 it would helpful if the title used "phantom electrical load" I initially thought this might have been about phantom partitions or data or functionality not under the control of the owner/user.
- PaulHoule 6y agoThe NVIDIA Shield TV can be configured to disable individual USB ports.