5 ms·
The big wooden sign in the jar is jaw dropping. I figure he must have cut it into sticks, fed them in, then glue it together then sand down and finish the outs
by jandrese 6y ago
The big wooden sign in the jar is jaw dropping. I figure he must have cut it into sticks, fed them in, then glue it together then sand down and finish the outside to hide the lines.
I assume the padlock had to be disassembled and then reassembled inside the jar as well.
- WalterBright 6y agoThe deck of cards could be inserted by: 1. removing all the cards from the box 2. unfolding the box 3. rolling the box into a tube so it will fit into the bottle 4. unrolling and refolding the box in the bottle 5. roll each card, insert in bottle, unroll 6. put the cards back in the box Of course, doing all this would be very tedious, and would be easier if one used some specialized tools, but it's doable.
- noman-land 6y agoIf you look at this one. You'll notice there's not enough vertical room in the bottle to for both the box and a card to slide in from the top. The bottle would need to be twice as tall. http://bottlemagic.com/wp-content/uploads/2011/01/Cards-in-Bottle-1-1.jpg http://bottlemagic.com/wp-content/uploads/2011/01/Cards-in-B...
- function_seven 6y agoOnce the box is in the bottle, waiting for cards, then they don't need to stack. The card will unfurl as it clears the neck, and enters the box. I'm sure the 52nd card is harder than the 1st, but there's wiggle room there. EDIT: Your photo shows a cellophane-wrapped box. I got nothing for that part!
- abhgh 6y agoProbably another excruciating step - cellophane goes in, box goes in and is put in the cellophane, then the cards, then the cellophane cover is sealed. Irrespective of whether this is the case or not, I am blown away!
- bb88 6y agoI'm thinking you have the carton flat inside the cellophane and insert both.
- c1ccccc1 6y agoHow about this? Carefully take the cellophane off the box without ripping it, or maybe just make a cut in the bottom. Then put the pack of cards in the box as above. Then put the cellophane through the bottle's neck and slide it back over the deck of cards.
- WalterBright 6y agoBasically, all of them look like some form of disassembly, insertion, and reassembly inside the bottle. Much like ship-in-a-bottle. Still impressive, though.
- noman-land 6y agoPretty much very similar to the ship in a bottle hobby. But then you look at something like this and are just like, wait did this dude seriously just unsew a pair of loafers and resew them inside the bottle? Wow. https://photos1.blogger.com/blogger/459/2465/320/bottle05.jpg https://photos1.blogger.com/blogger/459/2465/320/bottle05.jp...
- dole 6y agoThat padlock below the neck is killing me.
- chii 6y agoInsert a disassembled padlock (without the ear of the lock) thru the bottle neck, and reassemble it inside the bottle. Then, carefully hook the ear into the cork, and insert it into the bottle, then carefully attach the ear into one of the holes of the padlock. Then fully insert the cork, and then use some shaking of the bottle to click the padlock into a locked position. Or they just used magic.
- SoapSeller 6y agoCork in two parts - one that you can push all the way through, put the lock on, and then pull out and connect the outer part. (this also match the twine in the cork)
- caf 6y agoIt reminds me of a quote from Teller: "Sometimes magic is just someone spending more time on something than anyone else might reasonably expect."
- 6y ago
- function_seven 6y agoThe wooden sign is even more astonishing. Assuming that your guess is correct (sliced, inserted, glued), then the engraving on the front would need to take the kerf of the saw cut into account, or else it would show. Wait, now that I think about it, I bet it was split rather than sawed. The photo on the site is fairly lo-res, but it does look like straight-grained wood that would split straight, and would seamlessly glue back up. And it would reduce the amount of surface work needed afterward. Each piece would key into the next.
- mattnewton 6y agoHow would you split it without leaving tooling marks at the top though?
- function_seven 6y agoSplit it, then remove the tooling marks by slicing off a bit of all the slices, then insert into the bottle.
- Anarch157a 6y agoLike kung fu fighters split boards. Hold it from the edge and give it a whack.
- munificent 6y ago> then the engraving on the front would need to take the kerf of the saw cut into account, or else it would show. Or just engrave the pieces after they're cut while they're clamped together.
- rkangel 6y agoI was assuming that the wood was steamed and then compressed. It depends what sort of wood that is.
- fortran77 6y agoThere are many woods that can be steamed compressed, and then re-expanded with boiling water.
- jandrese 6y agoI have a tough time believing there are any that can be compressed to a tenth of their original size and then rebound back to full size.
- lokedhs 6y agoYou can check Youtube for videos where people make an impossible nail-in-wood construction, and you'll see just how much you can deform it. It's quite remarkable.
- IncRnd 6y agoThe note next to the picture with the wooden sign says, "Our venerable curator has gone nearly blind with a magnifying glass but has failed to find any sign of breaks or glue in this plank."
- bb88 6y agoThat's important because the edge of the board is right next to the glass so any imperfections would be caught instantly.
- jayd16 6y agoHow reliable is that flavor text? There appears to be a few dark lines running horizontally (could just be more grain though).
- IncRnd 6y agoIt's probably reliable, since it's very easy to fit wooden arrows through small holes in the middle of a metal coin, even when they "apparently do not fit".
- rossjudson 6y agoNo particular need to sand down the outside. A veneer can be glued on. The veneer could be rolled up, inserted, unrolled, and then applied.
- cerebrum 6y agoPossibly softened it through steam, look for "Impossible nail through wooden block" in this thread.