8 ms·
Large expensive equipment (shipped in custom-built pallets) use this. About $3/each to ship a $100+K box. https://www.amazon.com/Tiltwatch-STWPLUS-Plus-Label-P
by dekhn 7y ago
Large expensive equipment (shipped in custom-built pallets) use this. About $3/each to ship a $100+K box. https://www.amazon.com/Tiltwatch-STWPLUS-Plus-Label-Pack/dp/B00KG4BJN2 https://www.amazon.com/Tiltwatch-STWPLUS-Plus-Label-Pack/dp/...
- exhilaration 7y agoHow does one acquire these without triggering the tilt alert?
- draw_down 7y agoI'm imagining a very low-tech solution to this one.
- phren0logy 7y agoYou don't, you just flip them all around and jiggle them to reset them. Then you hope nobody does that to your box...
- Johnny555 7y agoAre you sure? There are holes in the yellow backing that look perfectly placed to have some sort of retaining pin inserted to hold the balls in place until use. At first I thought they were meant to insert the ball, but the holes look too small.
- LeoPanthera 7y agoIf you don't know, don't guess.
- phren0logy 7y agoThe ones I used (20 years ago?) worked this way. It's not a guess, it's just outdated. Regardless, my apologies for the inaccuracy.
- SamBam 7y agoI guess those ones didn't have the 180° sensors on them? With these one it would be pretty much impossible to jiggle both balls into place.
- pretendgeneer 7y agoI believe those dots above the start area have something pulled out when you take the back of the sticker that stops it from rolling around until it gets applied to the correct thing
- ogre_codes 7y agoThere are little dots at the top of the place where the each ball starts. I expect there is something in those spots which prevents the balls from moving and you remove it before you apply the detector.
- klodolph 7y agoYou can see that in each section, there is a small hole in the back where you can see the box through the hole. When you buy these, each hole has a pin in it, keeping the ball in the starting area. When you pull the indicator off the backing, the pins come with it. So you only have to keep it upright after you peel the backing off. Here is a video: https://www.youtube.com/watch?v=TuLClpWRmQ8 https://www.youtube.com/watch?v=TuLClpWRmQ8 You can see that each hole has a red colored pin in it, and you can see the pins come away with the backing (at about 0:21 in the video).
- tantalor 7y agoThat means the pins could be replaced one at a time to reset the device back to its original "unperturbed" state.
- function_seven 7y agoTo replace the pins, you'd need to tear the device off of the package. I assume that means cardboard is coming off with it, and the adhesive is ruined for re-application. So now you need to apply new adhesive, and do a good enough job that the recipient doesn't catch on to your shenanigans.
- derefr 7y agoOr you could order your own batch of them and, right before handoff, rip off their sticker and then affix yours to cover the damage. ...which is presumably why these have unique serial numbers! They really did think of everything. (You have to make sure the shipper communicates the serial number to the recipient for that part to function, though.)
- frandroid 7y agoYou ship them in a box with one sticker applied to the side, of course. #inception
- heartbeats 7y agoDoesn't being mass-produced sort of defeat the purpose? Buy an identical label, replace the barcode, and you're done.
- paxys 7y agoNot if it is stuck inside the box.
- rootusrootus 7y agoI imagine half the point (or more) is to be very visible to encourage anybody handling it during shipping to be careful.
- ska 7y agoThat's why you do both. They are cheap (relatively).
- mattkrause 7y agoUntil someone checks the serial number. See the C097412 in the bottom-right corner? Your replacement will be C097413 or something, and won't match.
- heartbeats 7y agoYeah, but if you replace the barcode that's not a problem. I suppose you could stick one on the inside and one on the outside, as paxys suggested. Then you'd have both deterrent and tamper-resistance. As an extra bonus, if some schmuck tilts and replaces it, the deterrent will still be in force for the next guy down the line.
- mattkrause 7y agoThe serial number is--in theory--recorded by the sender specifically so that you can't just swap them out. You put sticker #C097412 on the crate yourself, record the number, and the shipper takes it away. If things arrive damaged--and these are usually used on very expensive shipments--you can check the tilt indicator AND its number. I would bet it's much worse if indicator #D108523 arrives instead. As an added impediment, they're often on the surface of the item but buried beneath a bunch of plastic wrap/padding/etc.