3 ms·
Have you any info about how you regenerated the battery?
by pbhjpbhj 7y ago
Have you any info about how you regenerated the battery?
- pkorzeniewski 7y agoI sent it to guys that regenerate laptop batteries, but next time I will do it on my own because you basically replace the cells, weld them together and its done - here [1] you can find detailed guide for Libretto. [1] https://webcache.googleusercontent.com/search?q=cache:frP4SGL0HYUJ:https://www.notanon.com/electronics/rebuilding-a-toshiba-libretto-50ct-battery-pack/2011/03/18/+&cd=1&hl=pl&ct=clnk&gl=pl https://webcache.googleusercontent.com/search?q=cache:frP4SG... (from cache as it doesn't seem to work right now)
- legooolas 7y agoBe extremely careful if soldering Lithium-Ion batteries together, as getting them too hot (which isn't very hot compared to soldering!) can easily cause them to burst into flames or explode...
- rasz 7y agowelding != soldering
- mdip 7y agoI'll second that... Now, I'll say, after 30-40 batteries, I've never had one catch fire. I've had a few that I probably broke as a result of heat, and I suspect that if you've tested the cells carefully and the batteries are in good condition, that they tolerate the brief heating better than cells that are already damaged, but that's not something I'm willing to bet my shed or my body on.
- pbhjpbhj 7y agoWhen you said regenerate I thought you were doing some prices on the existing cells, rather than just replacing them. Thanks for your reply.
- mdip 7y agoMany older laptop batteries are simply a set of 18650 batteries wired together. I've "fixed" about 30-40 batteries. (1) Carefully take the battery pack apart, (2) Visually inspect the cells for any that are bulging or just, otherwise, look wrong -- take these to the electronic recycler, (3) charge each cell in an 18650 charger (mine is a Micro USB unit that charges very slowly), (4) test in a multi-meter, toss any that are bad, (5) put them in a low-drain device for a few hours[0] and throw out any that under-perform. In a typical "failed battery" there's rarely more than one dead cell in my experience. And I've had packs with as many as 9 cells. From there, it's a matter of putting it all back together. There's soldering involved, and you have to be extremely careful -- hit the battery with the temp required to melt the solder for too long and you have a seriously dangerous situation on your hands. I use two 3D printed clips and alligator clamps to hold the wire, wand and battery at distance from one another, battery on the bottom, wand on the top, wire in-between, and a 120mm fan, requiring me to only hold the cable to the wand and the length of solder. Can't caution enough that it's exceedingly dangerous soldering this kind of battery. I originally built the rig because I wanted to improve the quality of my soldering -- I'm pretty terrible with an iron, but I made several changes after I had a small number of batteries start failing after repair and a few searches led me to believe I may have damaged them[1] with my poor soldering skills. My rig involves two 3D printed clips, one to hold the iron exactly where I want it, and one to secure the battery. The cable to the iron has a length of wax lace on it to let me pull it back up/remove the iron from the rig with a yank at a distance. I use an alligator clip to hold the wiring in place and a long length of solder so that I can stand an arms length away. The iron "drops" in -- it's mounted on top, battery on bottom, wire in-between -- so I can heat it up an inch or so from the battery, I place tip of the length of solder in its spot and "tap" the wire of the iron to drop it into place. When I see it melt the tip of the length of solder and the small amount that's on the wire, I pull up on the string to move the iron away, wait a few seconds so the 120mm fan can cool things a little, and put a new battery in. Goggles, gloves and a nearby fire extinguisher of the right kind are a really good idea. I also do the work in a large, mostly empty, shed with doors that, when opened, eliminate nearly an entire wall and work directly on the cement floor. A lot of devices use 18650s and not all 18650s are the same. The one powering your drill might be able to handle higher drain than the one that came out of your laptop; don't mix those up. I was given a cardboard box full of dead laptop battery packs from the same model, so I was taking cells from a similar source each time. [0] I use an adapter that lets me power a Raspberry Pi via an 18650. [1] And likely made them into a fire hazard on their own.