6 ms·
Do not buy "bulbs," they are hopeless. Just buy a whole fixture with a big aluminium PCB and directly bonded chips.
by baybal2 8y ago
Do not buy "bulbs," they are hopeless. Just buy a whole fixture with a big aluminium PCB and directly bonded chips.
- mikepurvis 8y agoI wish there was more selection available of that kind of thing— when I last looked a year or so ago there was basically just one option at Home Depot, and it had the aesthetics of something you'd put in the laundry room. Worse than that, though, it was unusable with a dimmer switch; the whole thing visibly flickered every few seconds. I felt bad returning it because I really wanted it to work out, but the quality just wasn't there.
- tachyonbeam 8y agoI have an LED fixture that I got from home depot that is dimmable, no flickering. It's connected to a normal dimmer switch. I bought it about a year ago. My other LED fixtures were ordered through aliexpress. The fixtures were fine, but the transformers that came with the fixtures all failed and had to be replaced (overheated, melted the plastic casing). This turned out to be tricky, because the LED drivers available on ebay and aliexpress are never the same, there are constantly new shoddy ones from noname brands, and the ones I had bought before tend to be nowhere to be found when I need a new one.
- nsxwolf 8y agoI didn't know that the fixtures themselves had dimming features. I put "dimmable" LEDs in my can lights in the basement, and I'm really unimpressed with them. They don't flicker[1], but they don't get very dim, either. [1] Except after a power outage - then they eerily flash on and off like something out of Stranger Things.
- Freak_NL 8y agoThat is the constant frustration of this economic model. Either you buy the driver (or the LED bulbs for that matter) from a shop in your own regulated economic area (like the EEA) and have them handle quality assurance (including the selection of the product) and warrantee, or you get the same product directly from China for a fifth of the price and have to handle the occasional failure yourself. The sad thing is that the latter is still cheaper than buying from a 'local' shop.
- rainbowzootsuit 8y agoI have had good success with, and have been happy with the quality of _MeanWell_ LED drivers and power supplies. You can get them through Mouser, Newark, Digikey etc.
- ip26 8y agoThere's a lot of junk to be sure but tens of Philips & GE bulbs have been doing great for me for a couple years now. They don't run that hot either.
- neonkiwi 8y agoI was surprised at the early failures of my Sylvania bulbs. Had expected that going with a brand that has been in the light bulb industry for a long time, I would get decent quality, but they've all died in under a year. Now IKEA bulbs are my go-to, the mix of selection, quality and price is impressive compared to what I've seen but I haven't thoroughly researched this. Do Philips or GE do better?
- RankingMember 8y agoThe last I looked at them, Ikea bulbs ran hot the packaging advised not to be used in small/enclosed fixtures because they could overheat. Do you find that to be the case with the ones you're using?
- simongr3dal 8y agoI have a couple of 2W/80lm ikea bulbs for bedside lighting, and they are room temperature. I also own some 5W/400lm ikea bulbs for general room lighting and they do run warm, maybe something like 40°C ± 5°C. The fixture/thingy around the bulb is roughly the size of a fist. The bulbs are pretty new so I can't say anything about the lifespan of the bulbs, but the price is reasonable, they are not the fancy smart bulbs.
- ip26 8y agoI have only my anecdotal experience, but I'm happy with the Philips & GE bulbs. As I said, they both seem to run pretty cool. Philips makes what seem to be inexpensive-but-quality bulbs, as well as dimmable LED's that red-shift like incandescent used to. They also make a 60W yellow bulb that has very low blue emissions, uncommon for LED bulbs. Some of GE's LED bulbs have really high CRI which I like for making the basement more cheery. One thing to pay close attention to on the package is whether the bulb can be run in an enclosed fixture. The package should always specify. Following this guidance and picking the right bulb for the fixture will help ensure you get the service life you expect. I don't think I've found any 100W equivalents that are OK'd for fully enclosed application, and 60W equivalent is like 50/50.
- greedo 8y agoI bought one of these for my basement hallway when I was finishing it out. My only concern is that a normal fixture has few failure modes; just the bulb. But if this fixture fails, I have to find a new one that will fit in the same spot. Hopefully it will last til I'm dead.
- setquk 8y agoHonestly I can't be bothered to replace the fixtures. Edit: looking at the price of fixtures, the economic argument is poor as well.
- deleted 8y ago[deleted]
- amluto 8y agoI used to think that, and I changed my mind. The fancy retrofit fixtures are almost universally flood lights where the diffuser is close enough to the ceiling plane that it’s visible from far off axis. The result is that the lights on the far side of the room cause unpleasant glare. With a retrofit lamp, you can use a high quality trim baffle (these things cost about $12, are quite well designed, and are probably already in your house and put a civilized PAR30 or PAR38 LED in, and you get a much better light distribution. Back when lamps were all standardized incandescents, fixtures could focus on quality. Now, with LEDs, I suspect that manufacturers focus on how cheaply they can build a driver and assembly that meets some minimum performance criteria. So, with retrofit lamps, at least the fixture design is separate. (There are exceptions, of course. Very high quality dedicated fixtures exist, but they’re quite expensive.)
- JohnTHaller 8y agoMy friend's bathroom light that is now a strobe light and the landlord has yet to replace because it requires an electrician to replace the whole fixture would like a word with you.
- dsfyu404ed 8y ago>requires an electrician to replace the whole fixture would like a word with you. Kind of like how replacing a gas dryer "requires" a licensed plumber to make the gas connection or you're "required" to drive no faster than the speed limit at all times. You're getting the runaround. If it was in a vacant apartment that they were showing to people it would already be fixed. If they cared about getting it done ASAP they'd either shell out the big bucks or ignore the law. Edit: I think a lot of people on HN don't realize how simple swapping failed parts is. Swapping a failed water heater or electrical fixture (especially light fixtures) is a waste of the skilled tradesman's time and the customer's money. Even an incompetent landlord or maintenance service should be able to get it done.
- Sebguer 8y agoyeah, darn those pesky laws around liability getting in the way of some good old-fashioned handiwork.
- Consultant32452 8y agoAs long as you're just replacing the fixture and not running new line a handy man type person can do it legally.
- ceejayoz 8y agoIn some jurisdictions. IIRC, Australia requires an electrician for even this sort of minor work.
- JohnTHaller 8y agoGenerally, a landlord wants someone licensed with insurance to handle something like that on the off chance something goes wrong. I was going to fix the fixture in my bathroom that was shorting a bit and burning out bulbs myself. Thankfully I called my owner and he had an electrician come in because it turns out a lot of the conduit above the fixture needed replacing due to age.
- dreamcompiler 8y agoI've started doing this. Bought a large panel fixture and a separate high-quality LED current source and it has been absolutely great. Next time I build a house I'll probably run all the lighting circuits on a hefty 24VDC main power supply with small DC/DC regulators on every fixture. There's no reason nowadays why lighting circuits should be 120 or 240VAC.
- bombela 8y agopower loss and price of copper is a good reason to bring 120/240vac as far as possible.
- dreamcompiler 8y agoLike I said in a previous comment, with LEDs, power requirements are small and distances within a house are small. Coupled with a resonably high but safe voltage (like 24 or 36VDC), there's no reason why 14 gauge copper wire couldn't work just fine for a lighting circuit.
- kalleboo 8y agoIt's a shame that ceiling light fixtures in the US are directly wired and screwed in. In other countries (both in Sweden where I lived before and here in Japan where I live now) there are special ceiling power outlets, so replacing a light fixture is just a question of unplugging and plugging in again. Japan: https://farm5.staticflickr.com/4279/35698610491_8787f45eae.jpg https://farm5.staticflickr.com/4279/35698610491_8787f45eae.j... https://farm5.staticflickr.com/4230/35790814576_382943d360.jpg https://farm5.staticflickr.com/4230/35790814576_382943d360.j... Sweden: https://www.eldirekt.se/pub_images/medium/1890776__13222.jpg https://www.eldirekt.se/pub_images/medium/1890776__13222.jpg There's a wide range of quality ceiling light fixtures that you just clip into place, and the LED chips are on a huge metal heatsink so they run very cool https://panasonic.jp/light/led/products.html https://panasonic.jp/light/led/products.html