5 ms·
Any peripherals on this thing? They mention Ethernet and some SPI flash. How about USB or even a UART? I didn't expect a frame buffer, but what does it actually
by phkahler 9y ago
Any peripherals on this thing? They mention Ethernet and some SPI flash. How about USB or even a UART? I didn't expect a frame buffer, but what does it actually have? I thought they were going to have PCI via an FPGA, but no sign of that either.
- hucker 9y agoThey presented this at FOSDEM today, and ran the entire presentation (and a demo afterwards) on the actual hardware. They used PCI via an FPGA to interface with a standard ATI gfx card iirc. I don't know if the video is out yet, but have a look!
- phkahler 9y agoThat's what I hoped could be done. Did they use an open source ATI driver compiled for risc-v? That would make for a very interesting development rig.
- digi_owl 9y agoNo video yet that i can find, but it seem the slides are available. https://fosdem.org/2018/schedule/event/riscv/ https://fosdem.org/2018/schedule/event/riscv/
- mrob 9y agoThere must be a UART because there's a FT223H and USB port at the top left.
- digi_owl 9y agoThat micro port may only be for power. Or perhaps a client port to allow a PC to talk to the board without a network connection.
- joezydeco 9y agoYeah, that's totally a console port. The micro-B device connector gives that away.
- duskwuff 9y agoFor a FT232H on early development hardware, my first thought would be JTAG, not UART. Could be both if it's a '2232, though.
- jws 9y agoThe page mentions an FMC connector for future expansion, a standard FPGA expansion interface supplying 34 to 160 10Gb/s signals.† I don't know about varieties and compatibility, but Hitec makes a great number of interface cards for it, including an 8 lane PCI Express.‡ ␄ † https://en.wikipedia.org/wiki/FPGA_Mezzanine_Card https://en.wikipedia.org/wiki/FPGA_Mezzanine_Card ‡ http://www.hitechglobal.com/Accessories/FMC_Modules.htm http://www.hitechglobal.com/Accessories/FMC_Modules.htm
- gabesk 9y agoI wonder what signals they actually route out the FMC card. The website doesn't give a lot of information, but it seems like probably just ChipLink which they claim is their serialized TileLink bus protocol. So, you probably wouldn't be able to just plug a low-cost FMC module into the board. But with something like https://www.xilinx.com/products/boards-and-kits/ek-s6-sp605-g.html https://www.xilinx.com/products/boards-and-kits/ek-s6-sp605-... for another $500, you could theoretically use the DVI connector to provide a framebuffer, the PCI connector to interface to an NVME drive, and the FPGA to implement the logic of a TileLink endpoint as well as a minimal framebuffer and PCIe root complex.
- jackckang 9y agoChipLink is indeed routed out to the FMC. The demo during FOSDEM was done with a FPGA card attached to the FMC which then drove additional peripherals. Jack, SiFive
- justinclift 9y agoThe instructions for some of the previous dev kits point to "known good" FMC compatible adapters. The one that caught my interest right away is the PCIe module: http://www.hitechglobal.com/FMCModules/FMC_PCIExpress.htm http://www.hitechglobal.com/FMCModules/FMC_PCIExpress.htm There's also a PCIe expansion that works with it, so increase the number of slots to five: https://www.onestopsystems.com/product/%C2%B5cube3-expansion-enclosure-5-pcie-x4-slots https://www.onestopsystems.com/product/%C2%B5cube3-expansion... With those, it seems like enough to test out development for storage applications. eg NAS, etc.