4 ms·
Question: Why not go to 96V? Everything wants to go higher for all manner of reasons, and the semiconductor switches probably don't care all that much. If the
by bsder 10y ago
Question: Why not go to 96V?
Everything wants to go higher for all manner of reasons, and the semiconductor switches probably don't care all that much. If the jump has to be made, make the jump as far as possible so that the jump doesn't have to be made again.
Is there a safety reason or something?
- msandford 10y agoInertia and fear of the unknown. Also below 50V is generally considered "safer" and anything around 100 and up is "dangerous" due to the impedance of the human body.
- mixedCase 10y agoDangerous as in a bad kick, but it can't fry you like current AKA amps can (which is usually the worst part, which you want to avoid).
- deleted 10y ago[deleted]
- mindslight 10y agoThat's like saying that falling off a building can't kill you (because it's actually the stop that does). You lower the current by lowering the voltage.
- IanCal 10y ago> You lower the current by lowering the voltage. I assume you meant increasing there.
- Mchl 10y agoI = V/R So once the voltage is applied to your body, the higher it is, the more current flows through you (Some assumptions about source of electricity made)
- tempestn 10y agoIf you're talking about a controlled situation where you need to provide a given amount of power - ie driving the accessories of a car, then yes, a lower voltage would require higher current. P = IV When you're talking about safety though, the issue is what happens if the voltage gets applied to your body. In that case the relevant formula is I = V/R. R is the resistance of whatever circuit you've mistakenly formed through your body. The higher the voltage applied across that circuit, the higher the current that will flow. (This is also why it's more dangerous if you're wet, or in bare feet, for instance, because those things lower your resistance, resulting in greater current for a given voltage.)
- seanp2k2 10y agohttps://learn.sparkfun.com/tutorials/voltage-current-resistance-and-ohms-law/voltage https://learn.sparkfun.com/tutorials/voltage-current-resista... looks like a good resource if anyone reading this has no idea what we're talking about. Don't feel bad, we were all beginners once :)
- simcop2387 10y agohttps://www.youtube.com/watch?v=XDf2nhfxVzg https://www.youtube.com/watch?v=XDf2nhfxVzg Current and Voltage are intimately related. 1V with a 1kA capable supply will not hurt you.
- theatrus2 10y agoSemiconductors care a lot. There is a sweet spot in the <= 48V range, and even more in the <= 24V range. High voltage devices are much harder to miniaturize, and the conversion ratios for the inevitable logic supplies can be done a lot cheaper at lower voltages. Safety is of course a huge component. 48V is about the limit before special isolation and insulation is required.
- mindslight 10y agoTrunk full of rackmount telcom gear for IoT, duh. There actually is an existing sweet spot for 60V FETs, optimized for traditional 48v power systems. I've got to wonder if they're going to use -48v to allow simple driving of N FETs, or if the ubiquity of modern high-side drivers has made that a moot point.
- drzaiusapelord 10y ago48V is the threshold before you're regulated as a high voltage device. That means all sorts of safety standards, larger or less efficient electronic components, risk of injury, etc which translates directly to cost, risk, weight, etc.
- Grishnakh 10y ago>Question: Why not go to 96V? >and the semiconductor switches probably don't care all that much Yes, actually they do. Power MOSFETs are usually in the 30-60V range. When you go higher than that, costs go way up and you generally need to switch to IGBTs. MOSFETs capable of switching 30V loads at extremely high loads (like 100A) are dirt cheap. Power devices capable of switching 100V are not.
- IshKebab 10y agoAnything under 50V is considered "low voltage".