4 ms·
Yes, they can fail. Lots and lots of them fail immediately due to manufacturing defects. And over time, electromigration (where dopant atoms get kicked out of
by ajross 11y ago
Yes, they can fail. Lots and lots of them fail immediately due to manufacturing defects. And over time, electromigration (where dopant atoms get kicked out of position by interaction with electron momentum) will slowly degrade their performance. And sometimes they fail due to specific events like an overheat or electrostatic discharge.
But the failure rate after initial burn-in is phenomenally low. They're solid state devices, after all, and the only moving parts are electrons.
- jflatow 11y agoAs far as I understand, chips are designed with many redundant pathways for exactly this reason. I think its a rather important part of the design process, but someone who knows better should probably say.
- valarauca1 11y agoNot exactly. Reduancy is designed into chip hardware not to account for cosmic rays striking the wrong trace, but for manufacturing defects. For example Nvidia runs it's GTX 980 and GTX 970 production at the same time. The only difference is GTX970's can have up to 2 of their compute units non-functional. This is very commonly done in the industry. If you remember Phenom Dual, Tri, and Quadcores. Which were the same chip, just it was expected that only 5% of produced chips would be fully featured quad cores, the rest would be sold as other core counts. This was done with 27xx series i5, which were 34xx core i7's but with hyper threading disabled due to issues with yields on dye shrinks. If a single transistor fails, normally the whole thing dies.
- bri3d 11y agoThey're designed for manufacturing defects - this process is called DFM (Design For Manufacturing) and usually revolves around performing a Critical Area Analysis for defects of a given size. Design software is used to determine what would happen if a speck of dust of a certain diameter landed on the die in given locations. Then, the critical areas are spaced out and moved around to attempt to balance design constraints with yield. For large, expensive parts or parts in which a single common defect could easily blow the whole yield (for example DRAM, especially when embedded, CPUs with lots of cache or cores, and so on), regions (or rows and columns of memory) are generally fused off so that if one specific region fails qualification, it can be disabled without discarding the whole chip. This is the source of most 3-core CPUs, as well as the difference between most models in a single CPU family (they're often binned off based on how much of their L2 cache actually works). However, once parts are manufactured and qualified, they're pretty much done. Some hardware has BISR (Built In Self Repair) but as far as I know it's not particularly common outside of DRAM.
- revelation 11y agoBuilt-in-self-repair is a key feature in the old spinning rust hard drives and particular the new flash memory.
- ajross 11y agoIn neither case is the device "repairing" a failure like the ones posited here, though. Storage devices "repair" failures by detecting them and recovering the data using some form of ECC, and then rewriting it to a location that has not failed. No one has yet figured out a way to have a shorted polysilicon feature un-short itself in situ. :)
- exDM69 11y agoI work as a software engineer for a chip manufacturer. The fab (silicon manufacturing company) gives only a 5 year guarantee for the smartphone/tablet chips (with presumably some allowance). As years go by, the chip starts slowly degrading and some of the high performance chips start to get higher temperatures, worse power consumption, needs higher voltages, etc. The power management software counters this by keeping the clocks lower and the voltages higher, causing performance degradation over time to avoid catastrophic failure. When the same chips are used in products with higher reliability requirements, they are clocked down and more conservative power management software is utilized. disclaimer: not my area of expertise, I work on something completely different than power management.
- msoad 11y agoNow I understand why my iPhone gets slower after a year!
- avn2109 11y agoHonestly I'm pretty sure your iPhone slows down after a year because they build the software that way on purpose so as to incentivize you to buy a new one.
- macjohnmcc 11y agoMore likely they write software with the new hardware in mind but not wanting to fragment the market too much they offer the newer software to people with the older hardware and along with that comes some performance issues.
- barrystaes 11y agoWhich is what he said.. they thought this over.
- sneak 11y agoI am also pretty sure that Apple is intentionally adding more and more features to iOS to make it Do More Stuff so that they can sell more iPhones.
- vcarl 11y agoYeah, this is a real concern for computer enthusiasts who heavily overclock their CPUs. Higher clock rates need more voltage to be stable, but higher voltages increase electromigration. So maybe bumping the voltage from 1.3v to 1.5v stops your computer from crashing, but it could also cause your CPU to fry itself in 2 years instead of 10.
- PaulKeeble 11y agoI ran an I7 920 at 4Ghz for roughly 2 years at around 1.35V with water cooling (max was 55C on full load on all 4 cores). After the 2 year mark the chip became unstable and over the period of the next 6 months the clock speed it would reliably maintain was 3.2Ghz. On that progression it would be down below its default rated speed of 2.6Ghz in presumably another 6 months or perhaps outright failed. The current estimate is that Intel targets about 15 years for a CPUs life at the clock speeds they ship, overclocking can vastly decrease that.
- provemewrong 11y ago>They're solid state devices, after all, and the only moving parts are electrons. SSDs are solid state (duh) as well, and yet they degrade over time.