3 ms·
You'll never hear from them again: “We’re not looking to manufacture engines,” says company president Alexander Shkolnik. Instead, the company plans to continu
by ars 12y ago
You'll never hear from them again:
“We’re not looking to manufacture engines,” says company president Alexander Shkolnik. Instead, the company plans to continue developing the engine and work with a manufacturing partner
That's always a warning sign. To me it means they don't want to make a company, but are rather looking for a quick sale and exit.
Also: "Because so many potential applications are in the lawn care and landscaping biz, the current design runs on a mix of gasoline and oil for lubrication."
I doubt they'll be able to meet emission standards, which is another reason you'll never hear from them again.
- joelrunyon 12y agoCouldn't they just license the patent?
- chiph 12y agoInteresting comparison between automobiles and lawn equipment emissions: http://www.edmunds.com/car-reviews/features/emissions-test-car-vs-truck-vs-leaf-blower.html http://www.edmunds.com/car-reviews/features/emissions-test-c... The 2-stroke leaf blower was putting out 300 times the hydrocarbon emissions of a Ford F-150 Raptor. Looks like there's certainly room for improvement, and if this engine can beat it, it'll take some of the attention by the EPA away.
- SigmundA 12y agoThis has much to do with the crank-case scavenged valveless design of your typical two-stroke. Since it uses ports instead of valves there is a period of time where both the intake and exhaust ports are open and 20-30% of the unburned air-fuel charge goes right out the tail pipe. This allows for a very simple lightweight design but is no good for emissions or efficiency. Secondary to that is that again since these small two-strokes have no valves they use tuned exhaust to try and retain the charge going straight through with a counter pulse, therefore it is very difficult if not impossible to do a catalytic converter in the exhaust as they will interfere with the tuning. You notice the small 4-stroke is much better but not as good as the cars, this is because the 4-stroke has valves but no cat, it is also carbed instead of EFI. 2-strokes can be made with direct injection which delays injecting fuel until the exhaust port is closed by the piston, it adds much complexity and cost. Modern Evinrude E-TEC outboards marine engines have gone this route, whereas most other outboard makers have gone 4-stroke instead. Note that outboard marine engines do not require cats yet and emit about ten times the emissions per unit power that an automobile engine does. EPA is pushing for that soon though. 2-strokes can also be made with exhaust valves (called uniflow scavenging) this is usually done in large diesels since it also requires forced induction and no mixing of oil with fuel. These small wankel like engines should probably have emissions similar to the small 4-stroke rather than the small 2-stroke as the Wankel design does not have intake and exhaust ports open at the same time but they are still carbed and no cat.
- pan69 12y agoThis is pretty much how ARM works. They only design the CPU's but don't actually build them.
- MrBuddyCasino 12y agoYeah but manufacturing competitive silicon nowadays requires mucho dollares. Making small-scale engines is probably several magnitudes below that. Still, you've got a point.
- ars 12y agoDesigning a CPU is very difficult and building one is very difficult, so this works for ARM. But engines are not like that, there's little money in the design - there are tons of designs, they are interchangeable for the most part and one is only slightly better than another. And building them is not hard either, so there is little money in being just a build shop without having an IP. Usually a design-only firm licenses themselves exclusively to one retail company - they don't sell the component, only the final product. They goes on for a few years, then the retail company buys them and that's the end of it. That's why you'll never hear from them again, some lawnmower or whatever company will lock them up and that will be all. If they want to make an impact (and not just a quick exit) they become a supplier and sell full engines.
- xorcist 12y agoBesides what's already said, there's also big value for the manufacturer to guarantee that the CPU runs ARM code. Even if it was price competitive to design an ARM-based CPU from scratch, and avoid all the patents, you'd want something (bug) compatible with the real thing to in order to run real world code.
- beambot 12y agoThat seems overly cynical. Licensing is a perfectly valid business model, and it's becoming increasingly relevant as large companies do more outsourcing of R&D.
- jug6ernaut 12y ago"Also: "Because so many potential applications are in the lawn care and landscaping biz, the current design runs on a mix of gasoline and oil for lubrication." I doubt they'll be able to meet emission standards, which is another reason you'll never hear from them again." You do know that "mix of gasoline and oil for lubrication." is how EVERY 2-stroke gasoline engine works right? The handheld lawn & garden market is dominated by 2-stroke engines, all of which must meet EPA emission standards. FWIW, there are good 4-stroke engines in this area, but they hold a small market compared to 2-stroke, mainly because of the increased weight of 4-stroke engines