3 ms·
Would there be a future in somehow 3D-printing body armour that was lightweight and manoeuvrable using plates or links like the plate mail and chain mail of the
by prawn 13y ago
Would there be a future in somehow 3D-printing body armour that was lightweight and manoeuvrable using plates or links like the plate mail and chain mail of the past?
- fennecfoxen 13y agoPast armor used plates and links because the threats were arrows and swords and spears and junk. Today's primary threats are bullets, and I believe they have more luck stopping those with sheets of flexible, fibrous materials. Current 3D printing technology cannot create those. I doubt that older designs would help with losing a leg to a roadside bomb, either, but someone more qualified than I am would be in order to answer this.
- falcolas 13y agoI've heard of "dragon" armor being used - basically scale-mail type armor made of ceramic disks, incorporated into kevlar outfits. Seems like something where advances in 3d printing in different materials would benefit.
- pmahoney 13y agoCeramics can be 3D-printed [1]. The printed product is a paste of ceramic powder + binder that must be sintered (heated so the organic binder burns away and the ceramic particles fuse together into a strong, dense body). The as-printed part shrinks a bit during sintering, so you've got to account for that as well. [1] http://robocasting.net/index.html http://robocasting.net/index.html
- Scaevolus 13y agoAre there any connective materials that could withstand the sintering process?
- pmahoney 13y agoIt's been a while since I was in that field... Typical sintering temperatures are around 1000 to 1300 degC. Usually about 2/3 the melting point of the ceramic; enough to promote ionic motion leading to fusing of the powder in a reasonable amount of time (one-two hours for my lab-sized samples). Various techniques for lowering the sintering temperature are: - Increase the sintering time. The time required to achieve a given density (say, 95%) increases somewhat rapidly as you decrease the temperature - Add a glass to the ceramic powder. The glass melts and essentially lubricates things so there is sufficient motion at lower temperature. - Start with finer ceramic powder. This has higher surface area for a given amount, which is an energetically unfavorable state (the fused state has lower surface energy and is thus more favorable). - Apply pressure while sintering [3] - Live with less density. Pottery needn't be 95+% dense. Clay (or playdough) can be useful for some situations (not bullet-proof vest I imagine) if just let to air dry. - Other clever things I don't know about. I know there are metallic substances that can survive sintering processes, as in multi-layer ceramic capacitors, where a sandwich of ceramic/electrode/ceramic/electrode is sintered, but these tend to be the expensive metals that don't react with oxygen [1]. The polymer with the highest melting point I know of is Kapton [2], melting around 400 degC, which is quite a way from the 800 or so degC you might see after adding glass to your ceramic powder... All that said, most ceramics are not that tough in that they shatter when impacted. If you must 3D print bullet-proof armor, and are sure you can't print some kind of Kevlar-reinforced thing, then I'm not really sure what the best option is. [1] https://en.wikipedia.org/wiki/Ceramic_capacitor#Multi-layer_ceramic_capacitors_.28MLCC.29 https://en.wikipedia.org/wiki/Ceramic_capacitor#Multi-layer_... [2] https://en.wikipedia.org/wiki/Kapton https://en.wikipedia.org/wiki/Kapton [3] https://en.wikipedia.org/wiki/Hot_isostatic_pressing https://en.wikipedia.org/wiki/Hot_isostatic_pressing
- voidlogic 13y ago>Today's primary threats are bullets, and I believe they have more luck stopping those with sheets of flexible, fibrous materials. Those sheets stop lower power bullets, all the body armor that stops high power weapons has large ceramic panel inserts. Besides ceramics there are things like metal–graphene nanolayered composites that hold the promise tipping the armor/firepower balance back in the favor of armor.
- pavel_lishin 13y agoI don't know about armor for police and military - other commenters are covering that - but this could be pretty great for weapon-based martial arts competitions. My wife practices German longsword, and it's hard for her to find padded armor that fits precisely - men's jackets aren't cut right, and women's jackets are too small. Women's gloves are too small, and men's gloves are too big. If she could get a full-body kit printed out of metal that would be strong enough to stop a sword thrust, she'd be all set. (A few thousand dollars poorer, probably, but all set.)
- maxerickson 13y agoHave you tried getting something custom from whoever makes the padded armor? Seems likely they would be making most stuff by hand anyway (but I don't know anything about it).
- pavel_lishin 13y agoIt hasn't been a very high priority yet, but we'll look into it; I think it might be prohibitively expensive, but then again, can't really spar without it.