3 ms·
Does anyone know why a chip put in by hand will be faster than a chip put in mechanically (or whatever other means they could use)?
by freehunter 14y ago
Does anyone know why a chip put in by hand will be faster than a chip put in mechanically (or whatever other means they could use)?
- DIVx0 14y agoI think they mean that the layout of the die components were laid out and optimized by hand rather than letting an algorithm do it. I could be wrong though, I'm not an EE.
- Symmetry 14y agoYup, for the same reason that hand-crafted assembly is usually faster than compiled code. A human can just do more creative things to optimize a layout than our current algorithms can.
- protomyth 14y agoI just thought it was interesting given Apple's history: http://folklore.org/StoryView.py?story=Nybbles.txt http://folklore.org/StoryView.py?story=Nybbles.txt "The Apple II disk controller, designed six months after the Apple II itself was complete, was Steve Wozniak's crowning achievement. His five chip disk controller card out-performed competitive controllers that were four times as expensive by shifting most of the responsibilities from hardware to software. In Woz's approach, the software was responsible for doing all of the encoding and decoding, head stepping, etc. This allowed Woz to improve the capacity and performance over standard techniques." http://apple2history.org/history/ah05/ http://apple2history.org/history/ah05/ For two weeks, he worked late each night to make a satisfactory design. When he was finished, he found that if he moved a connector he could cut down on feedthroughs, making the board more reliable. To make that move, however, he had to start over in his design. This time it only took twenty hours. He then saw another feedthrough that could be eliminated, and again started over on his design. “The final design was generally recognized by computer engineers as brilliant and was by engineering aesthetics beautiful. Woz later said, ‘It’s something you can only do if you’re the engineer and the PC board layout person yourself. That was an artistic layout. The board has virtually no feedthroughs.’
- stordoff 14y agoIIRC, you can optimise the locations of sub-components to minimise on-chip communication delays. The automatic algorithms are pretty good, but can often be bettered (particularly if critical paths are identified and optimised).
- DigitalJack 14y agoIt won't always be faster. In fact, I'd argue if you had to lay out the whole thing by hand you would almost certainly do a worse job than "automatic" place&route. It's a matter of distance between components on the die, and transistor sizing. At the scale of complex integrated circuits, it's just about guaranteed that an automatic route will do a good job, but stands a good chance of messing a few hotspots up. I'm not an expert on the algorithms used for automatic routing, but there is some random guessing involved. You can even provide a seed for the random number generator. More often than not, a hybrid approach is used where the designer gives broad recommendations on where to place components and lets the autorouter go from there. Then at the end, the designer may go in and tweak some hot spots, or scrap it and start over with a new seed.
- X-Istence 14y agoAutomatic routing is still an NP complete problem, as in there is no perfect solution. This is the same issue with automatic routers for PCB's and the like, it is guess work along with some genetic sort of algorithm that steps through various options. I've had times where the auto router for a board gave up because it couldn't complete the routing, ripped everything up and did it by hand. Sure it took longer but the routes were shorter, and I finished routing the board with room to spare.
- ChuckMcM 14y agoChips, like printed circuit boards, are often laid out by algorithms. These algorithms try to optimize amongst a number of parameters such as active transistors per unit area, signal paths, power requirements, interference (things like electron tunnelling) and whatnot. As with a circuit board you can set the dial 'wide' and get a quick layout that is not optimal. You can dial it in and the algorithm will do most of the work and then stop on things it can't figure out (which an engineer then goes in and manually places). It's time consuming to do manual layout and the effects are not always immediately obvious [1]. So there is both a time component and a risk component to manual layout. It can however result in a smaller and more efficient chip. [1] When I was at Intel the 386 was the new hawtness. The first silicon samples powered up and ran which was awesome but at 'full speed' there were some issues that turned out to be related to a clock signal somewhere between the registers and the ALU. The design engineer replaced a metal feature (typical conductors were done in the metal layer) with a polysilicon version which had the effect of slowing down the propagation speed enough to line up the clocks. (it was fortunate it didn't need to go faster which is harder to do :-) These days the device geometries are so small as to require a lot of analysis which I would not enjoy trying to do by "hand".