3 ms·
For phones, it wouldn't make a difference to most repairs. The repair shops that work at PCB level swap major components between PCBs. It's rare that one of the
by Aurornis 1y ago
For phones, it wouldn't make a difference to most repairs. The repair shops that work at PCB level swap major components between PCBs. It's rare that one of the passive components is the cause of a failure on a PCB at this density. Even with the schematic it would be hard to diagnose many failure modes without a lot of trial and error. So they don't waste their time, they just swap the major ICs into a different board that has been salvaged from something and try that.
Schematics for high-density boards like this are not as informative as you might expect. It's mostly connections between balls of ICs and the values of passives here and there. The values of those passives can be measured from parts salvaged from boards if necessary. More likely, the technician would simply steal the part from another PCB that has been scrapped.
- mschuster91 1y ago> It's rare that one of the passive components is the cause of a failure on a PCB at this density. There have been a few videos posted here or showing up on my YT feed for phone repairs, iirc the voltage/battery regulators are things that do like to fail (and pretty obviously, when looking at the pcb with a heat camera).
- Aurornis 1y ago> iirc the voltage/battery regulators are things that do like to fail Those are actives. On a highly integrated device like this it would most likely be an application-specific PMIC (power management IC) that isn't generally available. It would be an IC that would be salvaged from one board and transferred to another.
- kragen 1y agoWhat kinds of application-specific things would it do? Have a weird pinout? Have slightly different voltage thresholds? Have a strange sequencing between different power supplies? None of that is rocket science; you could program an off-the-shelf microcontroller to do any of that (maybe with a breakout board and a couple of bodge wires).
- InitialLastName 1y agoAll of the above, plus implement the control interface expected by the driver and maybe control loops to keep the voltages in range at the point of load. You probably could do it with a breakout board, but good luck getting the right voltage drops to the chip (or fitting it in a cellphone case).
- kragen 1y agoI mean you can put an 0.1mm flat flex board between the board and your chosen microcontroller to get the power and ground pins in the right place.
- Aurornis 1y agoIt's far more complicated than that. You are not going to replace an iPhone PMIC with a microcontroller and some bodge wires. Even if you could nail all of the logic, the bodge wires alone would be an order of magnitude more loop inductance than the tightly designed PCB and it just would not work. The PMIC for a modern SoC is tightly integrated with the SoC. It handles power management, supply sequencing and timing, transitions between power states, standby modes, battery charging, and communication with the SoC. There is digital communication between the SoC and the PMIC to control all of this. This isn't something you kludge together with a microcontroller and some off the shelf parts.
- kragen 1y agoExcept for the digital communication, inductance mostly helps you here, not hurts. You don't want submicrosecond rise times on your power rails. I haven't seen modern SoCs with tightly integrated PMICs like you're describing, but they could certainly exist. But if they're not using an off-the-shelf chip, why don't they just integrate their power management functions into the SoC? Not enough balls?
- Dwedit 1y agoI've seen a whole lot of videos of laptop repairs where the only problem was a bad capacitor, and replacing the capacitor removed the short and fixed the laptop.
- Aurornis 1y agoThe capacitors that fail in laptops (and other full size electronic devices) are typically electrolytic caps, which have much shorter lifetimes than other capacitors. Phones do not have electrolytic capacitors because they are too small.
- Dwedit 1y agoI was referring to the tiny surface-mount capacitors. Are those often electrolytic?
- mrheosuper 1y agoExtremely wrong here, The most common capacitor to fail inside those laptops are ceramic one.