3 ms·
Just to give some numbers here: Assuming 600 volts (which is the highest rating for voltage I've seen in a commonly available wire) you would be sending 5600A d
by ars 14y ago
Just to give some numbers here: Assuming 600 volts (which is the highest rating for voltage I've seen in a commonly available wire) you would be sending 5600A down that wire.
That would require a wire 2 inches thick (1 inch radius), not including the insulation. I doubt most people would even be able to lift such a wire.
A 15 foot length would weigh 416 pounds! (Assuming no ground - with a ground it's 625 pounds.)
- Turing_Machine 14y agoIs that the continuous rating, though? Welding cables for intermittent duty are rated for higher currents, I think. Yeah, it'd heat up, but it would have plenty of time to cool off in between charges. You'd need to arrange things so that there was absolutely no way for the user touch the hot contacts and of course use high-temp insulation throughout (which welding cables already have). You'd want a docking station type of arrangement rather than a cable, I'd think -- maybe with some sort of clamp to really mash the contacts together. Arcing would be bad. :-) Certainly you couldn't run it off a normal wall plug. A big capacitor bank, maybe.
- ars 14y agoIt's the 90c rating. Got some new numbers after checking welding cables, looks like 1/2 inch radius will do, I calculate weight of 128 pounds for 15 feet, which is "better" - but still completely impractical.
- Turing_Machine 14y agoOnly if you're using cables. No one would do that. You'd have a solid docking station with fixed, solid contacts, as I (and the person with the post immediately above yours) said. You can use solid, fixed contacts at any temperature that won't melt the copper (assuming that they're well away from anything flammable).
- ars 14y agoYou still need cables inside the car. Maybe not 15 feet, but that much weight is impractical. If you really wanted to do this the only practical way is to increase the voltage - but of course high voltage is much harder to do safely.
- ChuckMcM 14y agoI think the only practical way to do something like that would be a couple of 12" diameter copper cylinders embedded in the floor connected to either a flywheel bank or a capacitor bank. Then your car would have a very large connector contact at the front and back. (and if it had a plastic pin that went into a groove in the road you would have a life sized slot car :-)) There is actually a lot of research on going in high current, short duration, energy systems. The one I am the most familiar with (which is to say read some of the papers) is EMALS the electro-magnetic aircraft launching system that is part of the 21st century X-carrier effort. That system is looking to replace the steam catapult on todays launchers with what is essentially a rail gun type device. Lots of advantages if you can make it work (like programmed acceleration profiles) but hard to make work. They were using flywheels spun up to 10,000 rpm to store energy as angular momentum and then dumping it into the rails with a genset attached to the flywheel.
- Xcelerate 14y agoYou could use a superconducting wire. (Yes, I know what you're about to say).
- archgoon 14y agoMight be feasible. You only need enough liquid nitrogen to keep the superconductor cool for a minute. Apparently, the Holbrook supercondcutor Project (http://en.wikipedia.org/wiki/Holbrook_Superconductor_Project http://en.wikipedia.org/wiki/Holbrook_Superconductor_Project) has been using superconductors in the Long Island power grid for years. > (Yes, I know what you're about to say). Please don't do this. If you know what the 'obvious' objections are, please say what they are. People unsure what the reasons for not doing so learn something. I'm certainly not aware of all the problems involved in using superconductors.
- deleted 14y ago[deleted]
- ars 14y agoSuperconductors don't do well with high currents so it's not a slam dunk, although they would definitely be lighter than regular copper conductors. But don't forget the wires inside the car.