4 ms·

You certainly need to think about that in the design. But by rolling a 'texture' into the sheets the structure is made from, you can make sure that any hole

You certainly need to think about that in the design. But by rolling a 'texture' into the sheets the structure is made from, you can make sure that any hole can't 'rip' bigger, and therefore fails slowly rather than rapidly. You also need pressure regulator valves in case of fire. And you might want to make the whole thing double or triple skinned so the highest pressures can be deeper inside where they are less likely to get punctured/less vulnerable to corrosion damage/crash damage.

usrusr 3y ago
But when do you really need a structure that has this exceptional strength on the happy path, but would still be good enough in terms of safety when pressure is lost? Unmanned aviation comes to mind, but the ratio between structural mass and battery+payload is already so low, even a zero-mass structure would not make a meaningful performance difference. It's all about the battery tech. Scaling up foil boating perhaps? Carbon fiber construction would certainly appear like a good candidate for taking advantage of being pressurized, and I perhaps naively take it as a given that materials is the major limiting factor in scaling up.
- londons_explore 3y ago
  > still be good enough in terms of safety when pressure is lost? You might not design for that case. A suspension bridge can't survive a tower falling over, or a cable snapping. The pressurized structures wouldn't be able to survive leaks over X size, and for leaks under X size, compressors would be used to maintain pressure.
- londons_explore 3y ago
  Rockets are the obvious use. The structure of a rocket is far heavier than the payload, and every kilo of weight you can shave off the rocket, you can add to the payload.
  - deleted 3y ago
    [deleted]
buran77 3y ago
At that point you're not dealing with a "flimsy structure out of thin steel foil" that you can inflate to hundreds of psi. You described what's basically a submarine, multiple high and low pressure hulls able to withstand hundreds of psi of pressure. Just for some reference, 1000psi is the kind of pressure you get ~700m depth (2300ft), double what a submarine would regularly withstand. Pressure in your average propane gas tank probably peaks around 200psi in high temperature. That steel isn't flimsy, it tends to get bulky and heavy even with creative ribbing and reinforcement. It has to make a lot of sense practically and economically to consider such an option. So it ends up being used in places where weight or cost matter less.
- londons_explore 3y ago
  A CO2 fire extinguisher is about 1000 psi.
  - buran77 3y ago
    A 1000psi fire extinguisher uses ~5mm thick steel even for that relatively small diameter cylinder. A typical extinguisher is ~200ish psi with a wall probably ~1mm thick. This highlights that high pressure and "thin steel foil" do not go well together and don't scale in your favor. Pressure makes any failure considerably more dangerous.

usrusr 3y ago

But when do you really need a structure that has this exceptional strength on the happy path, but would still be good enough in terms of safety when pressure is lost? Unmanned aviation comes to mind, but the ratio between structural mass and battery+payload is already so low, even a zero-mass structure would not make a meaningful performance difference. It's all about the battery tech. Scaling up foil boating perhaps? Carbon fiber construction would certainly appear like a good candidate for taking advantage of being pressurized, and I perhaps naively take it as a given that materials is the major limiting factor in scaling up.

londons_explore 3y ago
> still be good enough in terms of safety when pressure is lost? You might not design for that case. A suspension bridge can't survive a tower falling over, or a cable snapping. The pressurized structures wouldn't be able to survive leaks over X size, and for leaks under X size, compressors would be used to maintain pressure.
londons_explore 3y ago
Rockets are the obvious use. The structure of a rocket is far heavier than the payload, and every kilo of weight you can shave off the rocket, you can add to the payload.
- deleted 3y ago
  [deleted]

buran77 3y ago

At that point you're not dealing with a "flimsy structure out of thin steel foil" that you can inflate to hundreds of psi. You described what's basically a submarine, multiple high and low pressure hulls able to withstand hundreds of psi of pressure. Just for some reference, 1000psi is the kind of pressure you get ~700m depth (2300ft), double what a submarine would regularly withstand. Pressure in your average propane gas tank probably peaks around 200psi in high temperature. That steel isn't flimsy, it tends to get bulky and heavy even with creative ribbing and reinforcement. It has to make a lot of sense practically and economically to consider such an option. So it ends up being used in places where weight or cost matter less.

londons_explore 3y ago
A CO2 fire extinguisher is about 1000 psi.
- buran77 3y ago
  A 1000psi fire extinguisher uses ~5mm thick steel even for that relatively small diameter cylinder. A typical extinguisher is ~200ish psi with a wall probably ~1mm thick. This highlights that high pressure and "thin steel foil" do not go well together and don't scale in your favor. Pressure makes any failure considerably more dangerous.