5 ms·

This is a good and extensive guide. Most guides out there work with dev boards that are powered by usb. It's great to see a section dedicated to power them wi

by devsda 2y ago

This is a good and extensive guide. Most guides out there work with dev boards that are powered by usb. It's great to see a section dedicated to power them with alternatives like LM-1117. I'm still hoping to find a guide dedicated to power management of espxxx boards that includes guides for powering them with a range of sources like coin cells, aa, lithium, 9v, 12v batteries etc along with a primer on different features (like sleep modes) and their impact on power consumption to maintain the battery life. I always see mentions of all these interesting diy projects but not how they are powered. So, its difficult to get a complete picture of the maintenance needed and their usefulness in the long term.

2Gkashmiri 2y ago
I have an esp8266 hooked up to a solar inverter. it used to have problems with not getting enough power so i hooked up a power bank between the inverter and the esp. if the power from solar gets out, the power bank (10k mah on paper, must be less) can run it for around 36 hours on full charge.
- gh02t 2y ago
  Finding a powerbank that doesn't auto shut off with small power draws from a esp/microcontroller is hit or miss, it's not something that is advertised and the threshold can vary wildly. There are workarounds but they can get a little complex if you don't want them to just burn a bunch of excess power. I've also had bad luck with power banks that can survive outside more than a little while. Not moisture, you can seal that out, but heat and cold seems to kill the batteries.
YugyDugan 2y ago
That's like your nan being frustrated that there isn't a single definitive guide to buying a laptop. There are so many factors that it's a near-impossible task. And even if you somehow managed to do so, it would already be obsolete by the time you stopped typing. The datasheet (for each of the ESPxx, regulator, etc) will specify power consumption in different states. But sadly there's a lot of misleading amateurish pseudoscience in Arduino-land so you're best to ignore everything else (which would even include a guide like this, for example).
- TeMPOraL 2y ago
  How to read that info from the sheet? Problem: I have my NodeMCU gizmo with sensors and stuff, that works while powered via USB charger. I want to make it portable and powered by AAA batteries. How do I do it? I feel that my nan would've had an easier time figuring out on her own what laptop to buy.
  - stavros 2y ago
    Connect two AAA batteries to the 3v3 rail.
  - YugyDugan 2y ago
    That's not what it's designed for. That's like asking how to run your iPhone on AAAs. The hobbyist solution would be to find some obscure product on AliExpress with a holder for 2xAAAs and a 5V boost regulator with a USB connector. It's janky and inefficient, but that'll power your board, or your iPhone. The 'proper' solution would be to then take this prototype to an optimised design in your ECAD software of choice, integrating a AAA holder and choosing an appropriate regulator, and having some PCBs assembled. I'm not sure what else you could want. If the latter sounds daunting to you, it would be very easy for even an inexperienced EE on Fiverr to whip up for you.
- devsda 2y ago
  I think there's some misunderstanding on the expectations. Documenting a combination of all the available peripherals, boards and power sources is virtually impossible but that is not what I meant. Given a power source and board with defined power requirements (e.g. say 3.3v upto 150mA) if we can easily find what commonly available components are needed and how to wire them up (with tradeoffs) is sufficient. Here's an excellent video that touches lightly on what I meant. https://m.youtube.com/watch?v=heD1zw3bMhw https://m.youtube.com/watch?v=heD1zw3bMhw . PS: If you find the video format of tutorials useful for learning about electronics, Andreas Spiess and Great scott channels on youtube have very good content that is helpful for beginners.
  - YugyDugan 2y ago

by devsda 2y ago

2Gkashmiri 2y ago

I have an esp8266 hooked up to a solar inverter. it used to have problems with not getting enough power so i hooked up a power bank between the inverter and the esp. if the power from solar gets out, the power bank (10k mah on paper, must be less) can run it for around 36 hours on full charge.

gh02t 2y ago
Finding a powerbank that doesn't auto shut off with small power draws from a esp/microcontroller is hit or miss, it's not something that is advertised and the threshold can vary wildly. There are workarounds but they can get a little complex if you don't want them to just burn a bunch of excess power. I've also had bad luck with power banks that can survive outside more than a little while. Not moisture, you can seal that out, but heat and cold seems to kill the batteries.

YugyDugan 2y ago

That's like your nan being frustrated that there isn't a single definitive guide to buying a laptop. There are so many factors that it's a near-impossible task. And even if you somehow managed to do so, it would already be obsolete by the time you stopped typing. The datasheet (for each of the ESPxx, regulator, etc) will specify power consumption in different states. But sadly there's a lot of misleading amateurish pseudoscience in Arduino-land so you're best to ignore everything else (which would even include a guide like this, for example).

TeMPOraL 2y ago
How to read that info from the sheet? Problem: I have my NodeMCU gizmo with sensors and stuff, that works while powered via USB charger. I want to make it portable and powered by AAA batteries. How do I do it? I feel that my nan would've had an easier time figuring out on her own what laptop to buy.
- stavros 2y ago
  Connect two AAA batteries to the 3v3 rail.
- YugyDugan 2y ago
  That's not what it's designed for. That's like asking how to run your iPhone on AAAs. The hobbyist solution would be to find some obscure product on AliExpress with a holder for 2xAAAs and a 5V boost regulator with a USB connector. It's janky and inefficient, but that'll power your board, or your iPhone. The 'proper' solution would be to then take this prototype to an optimised design in your ECAD software of choice, integrating a AAA holder and choosing an appropriate regulator, and having some PCBs assembled. I'm not sure what else you could want. If the latter sounds daunting to you, it would be very easy for even an inexperienced EE on Fiverr to whip up for you.
devsda 2y ago
I think there's some misunderstanding on the expectations. Documenting a combination of all the available peripherals, boards and power sources is virtually impossible but that is not what I meant. Given a power source and board with defined power requirements (e.g. say 3.3v upto 150mA) if we can easily find what commonly available components are needed and how to wire them up (with tradeoffs) is sufficient. Here's an excellent video that touches lightly on what I meant. https://m.youtube.com/watch?v=heD1zw3bMhw https://m.youtube.com/watch?v=heD1zw3bMhw . PS: If you find the video format of tutorials useful for learning about electronics, Andreas Spiess and Great scott channels on youtube have very good content that is helpful for beginners.
- YugyDugan 2y ago