3 ms·
1. Two words: strain relief. 2. If it's outdoors, at least spray the electronics with Fine-L-Kote or similar to keep water vapor out. 3. Those relays look und
by Animats 3y ago
1. Two words: strain relief.
2. If it's outdoors, at least spray the electronics with Fine-L-Kote or similar to keep water vapor out.
3. Those relays look undersized for the load. Look at Grainger for similar ratings. Do not buy power relays on eBay or Alibaba. Current ratings there tend to be wildly exaggerated.
4. Er, overcurrent protection? An approved circuit breaker?
- sokoloff 3y agoHe says he installed a 50A OCPD, which is the same overcurrent protection an electrician would install and used relays from TE Connectivity (a respected brand) rated at 125% of the current the EVSE advertises as available. Both of those decisions seem perfectly sane/safe to me.
- StillBored 3y agoAre you an EE with a specialty in power electronics? Cause that seems insane to me, inductive loads will cause a voltage spike (flyback) when disconnected, which will exceed that easily. That is why there is generally a reverse diode across the contacts, which I didn't see in the diagram. Granted the article notes it appears to be largely a resistive load, but I would want data sheets on the car/charging requirements, not measurements, to ensure this is true 100% of the time. Maybe the car has an AC compressor or a pump to cool the battery during charging, which draws directly from the charger when plugged in. You might not see that doing a few random measurements because it turns on only after some time or if someone is sitting in the car.
- ferongr 3y ago>Maybe the car has an AC compressor or a pump to cool the battery during charging, which draws directly from the charger when plugged in No it doesn't. A/C compressors in EVs are 3 phase AC powered by an inverter supplied by the traction battery. The contactors in an EVSE open and close at practically zero current, the OBC ramps the current up or down accordingly. And as another sibling comment noted, the OBCs are PFC corrected and act as a largely resistive load.
- sokoloff 3y agoNo, but I'm a mechanical engineer who's taken a subset of my uni's EE curriculum, done a fair amount of hobby electronics, read a lot about the SAE J1772 charging standard that applies here, and disassembled two commercial EVSEs (all in contemplation of building my own EVSE, which I haven't pulled the trigger on yet). It turns out that the engineers who designed J1772 thought a fair amount about how to handle the connect/disconnect concerns that you raise (via the pilot signals and proximity microswitch) and they didn't just leave it to EVSE designers to YOLO it. > I would want data sheets on the car/charging requirements, not measurements, to ensure this is true 100% of the time The "datasheet" that you want is the J1772 standard. There are many free summaries of it, including https://openev.freshdesk.com/support/solutions/articles/6000052074-basics-of-sae-j1772 https://openev.freshdesk.com/support/solutions/articles/6000... Scroll all the way to the bottom and read the section on "Proximity" to understand how the relays are not disconnected while large currents are flowing.
- Geeek 3y agoAny Fine-L-Kote like recs that HD, Lowes carry?
- Animats 3y agoThat stuff has become much more expensive. $43/can on Digi-Key.
- StillBored 3y agoI used significantly higher-rated omron relays in a project I did a few years back to switch a 2.5HP motor on/off a few times daily. This area shouldn't be skimped on; relay contact arcing isn't a joke. This brings me to my second point: I don't see a cycle rating on those relays from the datasheet provided. Most relays are rated for ~1M cycles, some for ~10M or more, but beyond that solid-state relays start to be a thing. And so, I question if people are using mechanical relays to chop 50/60Hz AC power, which from my 30 seconds looking at the article/schematic appear to be what is happening here... That seems crazy to me, and I imagine it requires some exotic contacts in the relays to avoid failure in short order, which these relays don't appear to be. The data sheet mentions they are used for chargers/solar inverters/etc but that doesn't mean they are used at 50/60Hz cycling but likely just as a disconnect/power on function which cycles once per charge/day/etc. Then again, I don't really want to be this guys neighbor since chopping an AC line with that much load is going to generate an insane amount of noise, and I don't see anything in the circuit designed to damp it either.