4 ms·

I surely have. Any even semi-public USB power socket is hanging on by a thread, some of them have the inside paddles snapped off entirely. I haven't seen a Type

I surely have. Any even semi-public USB power socket is hanging on by a thread, some of them have the inside paddles snapped off entirely. I haven't seen a Type C one in such a state yet, but I eagerly await it.

holoduke 3y ago
The problem with usb c (but also mini and micro) is the weak connector on the device itself. The way its connected to the board is way weaker than a large usb a connector on a motherboard. Accidentally pullen a keyboard while attached will for sure destroy a usb c port. A usb a most likely survive.
- yencabulator 3y ago
  Simply put your money where your mouth is. Framework laptops come with expansion cards that are on sturdy rails and serve as the world-facing USB-C/A/HDMI/SD card/whatever connection. The inner connector on the mainboard is well protected. https://frame.work/assets/pdp/expansion-card-9240577483dc9e23bf019770192c518e34bc20c9daff3c37246c713f580adafa.webp https://frame.work/assets/pdp/expansion-card-9240577483dc9e2...
- arcticbull 3y ago
  That's going to depend on the connector. Plenty have through-hole mounts. You can also get surface-mount type A connectors.
  - janoc 3y ago
    They all do. Yet it still doesn't help. Those 4 little retaining lugs are fixed into the board only by solder, which is fragile and will crack after a while, esp. when the connector is mated/demated constantly and forces are applied to it. USB A has those lugs much larger and usually also bent under the board or twisted, so the connector isn't fixed into the PCB only by solder. USB C and micro USB are mostly designed for clamshell enclosures such as a typical phone - in that case the connector shell is supported by the enclosure itself (ideally through some flexible padding) and not only by the flimsy contacts/solder lugs. However, there are plenty of devices on the market where these connectors are not supported like that because the designer has been an idiot - and guess which devices end up in the landfill with broken off connectors the most. Breaking the old school USB A, square USB B or mini USB is almost impossible like this unless one applies really unreasonable amount of force. I have only ever managed to accidentally destroy a USB A port once like that by accidentally hitting a USB stick hanging out of it - but the board and the adjacent ports were fine, only the port shell and contacts were destroyed.
    - sokoloff 3y ago
      Mini USB-B is still not very robust in terms of connection the board. I’ve got a couple devices here where the port is ripped off the PCB. (I voluntarily [attempt to] repair devices for friends, so I see more than a typical rate of failed parts.) By some definition, that’s evidence of unreasonable force, but it definitely happens and should be anticipated when you put the device in the hands of lots of gorillas.
    - duskwuff 3y ago
      > Those 4 little retaining lugs are fixed into the board only by solder, You're saying this as though there's a single design of USB-C cable to board connector. There are, in fact, many different designs, including many with "lugs" which go through the board, as well as mid-mount connectors which use the material of the PCB as structural support.
- mnsc 3y ago
  Yup, bricked a old gopro with a mini connector by tearing it off the circuitboard. Didn't think that could happen so I wasn't particularly careful but it's physics, small things break easier.
Sakos 3y ago
I know the repair place I worked at sees a lot of broken USB-C ports. Way more than they ever had A. They hate the new, smaller ports because they're usually built very flimsily unless it's Apple.
rezonant 3y ago
To be fair, I haven't seen a USB C power port available in public once so far myself, and while it would be nifty for them to become the norm over USB-A, I really think it's a bad idea to subject users to unknown USB charging ports in public. A wall outlet can't pretend to be a keyboard, for instance.
herbst 3y ago
My laptop has a opinion which side is up on usb c and doesn't connect the other way around (the way docking stations use) I basically have to replace my laptop to use my docking station just because usb c isn't sturdy enough :/
- reportingsjr 3y ago
  Did the USB C port ever work that way? Extra electronics are needed to support being able to flip the high speed connects like that. Maybe the laptop never had that?
  - herbst 3y ago
    I bought it used and only realized it later, but yes it's supposed to work on both sides.
iforgotpassword 3y ago
Never seen a broken public A port, but maybe it was because the A port was already there for a decade and got good wear while public C ones are relatively new? And I think many people still use A to C cables on the go because those ports are way more common, so they just get a lot more wear.
- yencabulator 3y ago
  The terminal seating at LAX has both 110 VAC plugs and USB-A plugs where the cable falls out as soon as you let go of it.

holoduke 3y ago

The problem with usb c (but also mini and micro) is the weak connector on the device itself. The way its connected to the board is way weaker than a large usb a connector on a motherboard. Accidentally pullen a keyboard while attached will for sure destroy a usb c port. A usb a most likely survive.

yencabulator 3y ago
Simply put your money where your mouth is. Framework laptops come with expansion cards that are on sturdy rails and serve as the world-facing USB-C/A/HDMI/SD card/whatever connection. The inner connector on the mainboard is well protected. https://frame.work/assets/pdp/expansion-card-9240577483dc9e23bf019770192c518e34bc20c9daff3c37246c713f580adafa.webp https://frame.work/assets/pdp/expansion-card-9240577483dc9e2...
arcticbull 3y ago
That's going to depend on the connector. Plenty have through-hole mounts. You can also get surface-mount type A connectors.
- janoc 3y ago
  They all do. Yet it still doesn't help. Those 4 little retaining lugs are fixed into the board only by solder, which is fragile and will crack after a while, esp. when the connector is mated/demated constantly and forces are applied to it. USB A has those lugs much larger and usually also bent under the board or twisted, so the connector isn't fixed into the PCB only by solder. USB C and micro USB are mostly designed for clamshell enclosures such as a typical phone - in that case the connector shell is supported by the enclosure itself (ideally through some flexible padding) and not only by the flimsy contacts/solder lugs. However, there are plenty of devices on the market where these connectors are not supported like that because the designer has been an idiot - and guess which devices end up in the landfill with broken off connectors the most. Breaking the old school USB A, square USB B or mini USB is almost impossible like this unless one applies really unreasonable amount of force. I have only ever managed to accidentally destroy a USB A port once like that by accidentally hitting a USB stick hanging out of it - but the board and the adjacent ports were fine, only the port shell and contacts were destroyed.
  - sokoloff 3y ago
    Mini USB-B is still not very robust in terms of connection the board. I’ve got a couple devices here where the port is ripped off the PCB. (I voluntarily [attempt to] repair devices for friends, so I see more than a typical rate of failed parts.) By some definition, that’s evidence of unreasonable force, but it definitely happens and should be anticipated when you put the device in the hands of lots of gorillas.
  - duskwuff 3y ago
    > Those 4 little retaining lugs are fixed into the board only by solder, You're saying this as though there's a single design of USB-C cable to board connector. There are, in fact, many different designs, including many with "lugs" which go through the board, as well as mid-mount connectors which use the material of the PCB as structural support.
mnsc 3y ago
Yup, bricked a old gopro with a mini connector by tearing it off the circuitboard. Didn't think that could happen so I wasn't particularly careful but it's physics, small things break easier.

Sakos 3y ago

I know the repair place I worked at sees a lot of broken USB-C ports. Way more than they ever had A. They hate the new, smaller ports because they're usually built very flimsily unless it's Apple.

rezonant 3y ago

To be fair, I haven't seen a USB C power port available in public once so far myself, and while it would be nifty for them to become the norm over USB-A, I really think it's a bad idea to subject users to unknown USB charging ports in public. A wall outlet can't pretend to be a keyboard, for instance.

herbst 3y ago

My laptop has a opinion which side is up on usb c and doesn't connect the other way around (the way docking stations use) I basically have to replace my laptop to use my docking station just because usb c isn't sturdy enough :/

reportingsjr 3y ago
Did the USB C port ever work that way? Extra electronics are needed to support being able to flip the high speed connects like that. Maybe the laptop never had that?
- herbst 3y ago
  I bought it used and only realized it later, but yes it's supposed to work on both sides.

iforgotpassword 3y ago

Never seen a broken public A port, but maybe it was because the A port was already there for a decade and got good wear while public C ones are relatively new? And I think many people still use A to C cables on the go because those ports are way more common, so they just get a lot more wear.

yencabulator 3y ago
The terminal seating at LAX has both 110 VAC plugs and USB-A plugs where the cable falls out as soon as you let go of it.