7 ms·
My foxhole radio
- linker3000 15y agoFull marks only if bare copper wire was used and he cotton covered it himself!
- ja27 15y agoAnd built the speaker. That's one thing I haven't done in a crystal set. Just a coil, magnet or even scrap steel, and the right paper.
- jgrahamc 15y agoFunny what tickles the fancy of Hacker News, folks here might also enjoy my coffee can antenna that lets me leech WiFi from a hotel 1/4 mile away: http://blog.jgc.org/2012/02/long-range-wifi-antenna-from-illy.html http://blog.jgc.org/2012/02/long-range-wifi-antenna-from-ill...
- jrockway 15y agoIs the coathanger antenna cut to a particular length?
- jgrahamc 15y agoNo, and it's of no importance. It's just something that will make an electrical connection with the coil and stay there. Edit: I answered the wrong question here, thought he was talking about the coat hanger I used in the crystal radio set. In the case of the WiFi antenna it matters a lot!
- ja27 15y agoIt certainly does matter, especially on the transmitting side. It's just hard to predict how long it needs to be without breaking out antenna modeling software. Here's a site with a few different wifi antenna designs and some antenna modeling: http://www.lincomatic.com/wireless/homebrewant.html http://www.lincomatic.com/wireless/homebrewant.html This site has a calculator for cantenna dimensions: http://www.wikarekare.org/Antenna/WaveguideCan.html http://www.wikarekare.org/Antenna/WaveguideCan.html
- jgrahamc 15y agoSorry, I was answering a different question (the original question was a bit unclear). The antenna length certainly does matter as you point out, I thought the parent was asking about the piece of coat hanger that I use to sweep along the coil to find stations in my crystal radio. My mistake for misinterpreting the question.
- tocomment 15y agoHow does the diode work?
- jgrahamc 15y agoBluing steel turns the coating of the steel in magnetite, Fe3O4, which is a semiconductor. The point of the pencil is graphite and the result is essentially a Schottky Diode: http://en.wikipedia.org/wiki/Schottky_diode http://en.wikipedia.org/wiki/Schottky_diode They have a very low voltage drop which is vital for a crystal radio because the voltages involved are tiny and any lost voltage must be minimized.
- tocomment 15y agoThanks for the informative answer. Now my next question. Why does a radio need a diode to operate?
- jgrahamc 15y agoGo read about AM demodulation. It's pretty simple but a diagram really helps. The Wikipedia page on crystal radios has a good explanation: http://en.wikipedia.org/wiki/Diode_detector#Crystal_detector http://en.wikipedia.org/wiki/Diode_detector#Crystal_detector
- copper 15y agoRoughly, when you're receiving an AM signal, you use the rectifying effect of a diode coupled to a low-pass filter. The idea is that the envelope is all you really need to pass to the speaker, if the signal itself is powerful enough. http://en.wikipedia.org/wiki/Envelope_detector http://en.wikipedia.org/wiki/Envelope_detector
- ajuc 15y agoAM radio works by modulating carrier wave (of constant, high frequency), by voice (small, variable frequency). You want to get the voice, and if you just connected signal from antenae to the speaker, it'll be vibrating too fast for you to hear the voice. So you need to filter out the carrier part of the signal. Diode only allows current to flow one direction, and the rest of circuit allows it to discharge slowly (it has some capacity). When there is unmoduled carrier wave (silence on radio), there is balance between the current that flows thoruhgt diode, and the current of discharge, so the voltage on speaker is more or less constant (probably not on 0 level, but it doesn't matter). When carrier wave is modulated to half the amplitude, speakers gets less the voltage. So speakers vibrate with voice wave frequency, not carrier wave frequency, so you can hear the voice. Imagine you want to measure the daily sea level, and it's very windy (big waves). You can't just measure it once a day, because depending on the moment you'll measure high or low level of wave, and you want the average level. So you make a container that is filled by waves throught one-way pipe, and you drill small hole in the bottom of that container, so it leaks at a constant rate. When you tune the size of hole in the bottom, and the size of one-way pipe correctly, you can measure level of water in this container, and it will be proportional to the average level of water in the sea.
- Craiggybear 15y agoIf you put a high-value resistor (between 220K-470K) in parallel across the crystal earpiece the audio will be much stronger/clearer. OR you can use the high impedance earpiece form an old telephone instead of a crystal earpiece which will give a fantastic, clear and loud output. My grandfather used to put his "cans" from his crystal set in a pudding bowl and it acted like a speaker -- several people gathered around could hear it at the same time. A 300pf variable capacitor across the coil will also give you quite effective tuning.
- jgrahamc 15y agoThanks for the additional advice. I was planning to make a capacitor out of foil and newspaper interleaved. One day when I've finished all the other things I want to play around with...
- linker3000 15y agoThe other method is using a variometer (inductive), which is easier than making a variable capacitor: http://www.crystalradio.net/crystalsets/hassell/index.shtml http://www.crystalradio.net/crystalsets/hassell/index.shtml Newpaper will be 'fun' to work with as its moisture content will vary with environmental conditions, making its dielectric constant not very..erm..constant - unless you impregnate it with wax or a lacquer. (Made plenty of crystal sets during my teen years in the mid 70s-80s)
- Craiggybear 15y agoGood link to variometer page -- thanks.
- ja27 15y agoThere are lots of ways to homebrew variable capacitors. A sheet of glass and two pieces of scrap copper does well. I have a "crystal" radio (uses a modern diode) all built on a paper towel tube. The coil is wound on the tube like usual but at the other end of the tube there's also a layer of foil and a smaller tube with a layer of foil that slides inside that to make a variable capacitor.
- jeffcapers 15y agoI made one with a hacksaw blade and no tuning arm a few years ago - could pick up a single nearby station (just about). Have you looked into creating an earpiece/speaker? it's the "weak link" in such a basic setup.. always wondered if something could be cobbled together.
- deleted 15y ago[deleted]