3 ms·
They are unquestionably creating Hype without releasing data because that’s what’s best for the company. It’s fine for a private company to maintain stealth, b
by Retric 4y ago
They are unquestionably creating Hype without releasing data because that’s what’s best for the company. It’s fine for a private company to maintain stealth, but the combination of hype and not releasing meaningful metrics is a very bad sign.
High energy Neutrons are nasty, the issue with high atomic number shielding is it doesn’t slow them down very well. Sort of like tossing a ping pong ball at a bowling ball it just doesn’t transfer much energy. Even 1% Tritium would be a problem.
- pfdietz 4y agoI'm sorry, but the standard you are asserting there is simply ridiculous. You would have them be unable to say anything about what they are doing (the topic would ensure great interest which you call hype) without sharing all details. Of course neutrons will cause issues, but the point is the very energetic ones could be much less of a problem than in a DT reactor. It might make the difference between replacing the first wall once a year and replacing it once a decade (say). I will add that the cylindrical geometry should make such replacement much easier. I advise you to study what they've said with an open mind. I believe you'll change your opinion, or at least convince you to reserve judgment.
- Retric 4y agoJust build a working device and I am easily convinced, except why would they care about what I think if they have that. It’s really the technical details they are providing actually makes them seem more like a scam, if they shared less it might seem more reasonable. But sharing a lot except any relevant numbers while suggesting it’s ready soon screams scam. For example they need 2 DD reactions to on average produce 1 H3 which means their producing more high energy neutrons than a pure DT design for the same energy. If T is a waste product then they need to do separation etc. At the same time they are also going to have some DT reactions which means they will need basically identical radiation shielding either way. The idea of extracting energy from magnetic field interactions sounds plausible until you consider all the waste heat that’s being produced. Even if everything worked as described they would still want massive amounts of cooling which is either a problem or another power source. If they had said they are using a mix of both that would be far more believable.
- pfdietz 4y agoThey have built six working devices. These have not achieved the end goal yet, but the results have been enough to open the money spigots for more funding. Really, what is your problem here? I get a strong Dunning-Kruger impression from your objections. You think you know more than you do. Example: your objection to recovery of energy from the magnetic field. This is not hard to understand! They increase the magnetic field to compress the FRC. This heats the particles adiabatically, just like a piston compresses a gas. And JUST LIKE A PISTON, this is a completely reversible process: allowing the FRC to expand again does work on the coil, sustaining its current and allowing energy to be extracted.
- Retric 4y ago> allowing the FRC to expand again does work on the coil, sustaining its current and allowing energy to be extracted. Sure, some energy might be recoverable that way but what percentage of energy is extracted and what percentage ends up as waste heat. At a minimum those neurons from DD fusion, and photons from hot plasma etc are’t being recovered. A mere 100 MW device operating at an awe inspiring 90% efficiency would still be producing a 10MW aka a fuck ton of waste heat and I doubt anything close to 90% would be theoretically possible. Not to mention mechanical stresses etc from such detonations.
- pfdietz 4y agoNeutrons from DD fusion will carry a smaller fraction of energy that neutrons from DT fusion. They also don't need to breed tritium, and don't need to deposit their energy at high temperature (since no thermal cycle is necessary to convert that heat to power, especially in D3He-optimized reactors; the heat can just be dissipated.) This means the cooling could be simple, with water at moderate temperature and pressure. This would also shield the neutrons effectively. The heating part I'd worry about most is photons hitting the inner surface of the fusion chamber. These will be absorbed in a thin surface layer, and since the system is pulsed the instantaneous heating could be quite high. They might have to resort to a liquid layer that's ablated by the thermal pulse. This would eject gas into the chamber, but they're using a pulsed approach anyway so this could be ok, if the pulse is shorter than the time the evaporated gas needs to reach the plasma.