3 ms·
Bwaha, that’s just not true. As long as the paper is halfway intact, drywall is very difficult to remove and provides significant strength to a wall. It’s a co
by lazide 4y ago
Bwaha, that’s just not true.
As long as the paper is halfway intact, drywall is very difficult to remove and provides significant strength to a wall. It’s a composite material, and excellent fire barrier.
It’s really obvious when it’s up compared to not.
It’s not as much as lathe and plaster, but lathe and plaster is extremely difficult to work with in every other way, and far more labor intensive.
Plywood on a wall is important for shear strength, but lathe and plaster doesn’t replace it. Properly designed earthquake resistant shear walls became a thing long after lathe and plaster were phased out.
- clairity 4y agoi probably overstated my point by saying drywall has no shear strength, but we seem to agree that drywall < plaster & lath[0] < plywood in that respect. i'd suggest you've also overstated the strength of drywall as "significant". it's not nothing, but against an earthquake, it's approximately nothing. plywood backing, of course, is the minimum required by code for earthquake resistance. plaster & lath is harder to work with, but has many superior qualities (re: moisture, sound, heat, malleability) that it makes it worth it in many residential cases (not so much commercial, where reconfiguration is more frequent). [0]: a lathe is a machine tool
- bombcar 4y agoOr what you often find in residential construction, lath and plaster under drywall hahahaha (I die now).
- clairity 4y agothat sounds to me like a (bad) renovation. what really sucks is damaged plaster & lath being ripped out and patched with drywall. that's the worst of both worlds, since you don't get the seamless barrier that is plaster or the ease of use of drywall.
- bombcar 4y agoOh god there's so much bad renovations everywhere. My kitchen is technically an addition so one wall is: paint, drywall, wall paper (4 layers), lath and plaster, exterior cedar shakes, shiplap, and finally studs.
- lazide 4y agoBeautiful. Part of why that happens I think is everyone is afraid to peel a layer off for fear of what they’d see underneath. A lot of contractors try to avoid renovations because it’s a never ending series of pandora’s boxes. My favorite when checking out a potential house purchase once was a small wet spot in the middle of a wall. When I pressed on it with my finger - and my finger went right through - into live termites! That finger press probably saved me $75k and months of headaches.
- bombcar 4y agoYeah, I now assume any minor renovation project is exactly the same as a "tear down to the studs" rebuild. When it turns out I don't have to, I feel great!
- lazide 4y agoDepending on thickness and stud construction, drywall has higher calculated shear load than lath and plaster - https://up.codes/s/shear-walls-sheathed-with-other-materials https://up.codes/s/shear-walls-sheathed-with-other-materials There are easy to install drywall elements (heavier drywall, or sound deadening backing sheets) that also cut down on noise. As with all things, ‘it depends’. Lath and plaster isn’t used much anymore because the cost rarely outweighs the benefits. In non-seismic shear wall usage, it’s allowable to use either. (Edit: fixed my very persistent autocorrect from lath to lathe - doh, thanks for noticing that)
- engineer_22 4y agoIt's considered rude to laugh at an interlocutor's comment. You could bring an example of code or calculation instead of anecdote to demonstrate your point.
- deleted 4y ago[deleted]
- lazide 4y agoIf someone asserts that water flows uphill, I dare say I do not owe them maps of the local space time curvature. If that makes me rude, then feel free to downvote as desired.
- deleted 4y ago[deleted]