3 ms·
I want to see a "solar dispenser" that can drive very slowly across open land, leaving behind a trail of solar panels. Installation costs are a big part of cur
by londons_explore 4y ago
I want to see a "solar dispenser" that can drive very slowly across open land, leaving behind a trail of solar panels.
Installation costs are a big part of current solar farms, and a big part of that is the labour to assemble frames, do up all the bolts, connect all the wires, etc.
If we could make a single truck drive along at 0.5 mph leaving a trail of installed panels, it would really make installation far cheaper. The truck could take as 'input' a container of solar panels with the necessary legs and supports, maybe even concrete bases, all ready to go, shipped direct from the factory.
Other components could be combined to save costs too - for example, the inverter could be built into the panels. The panel frame and the mounting frame could be combined to save weight and assembly time. In a big line of panels, only the end ones have high mechanical wind loads, so middle ones could use far more lightweight plastic supports.
Then creation of a 1 acre solar farm could be as little as a couple of days work for 2 people driving the truck.
- i5heu 4y agoYes! this would be amazing! Since I've seen these Images, I am kinda amazed by the potential of this idea. https://www.artstation.com/artwork/dOkXJ1 https://www.artstation.com/artwork/dOkXJ1
- cinntaile 4y agoIt reminds me a little of those large coal excavators, but the similarity is probably just because these are big machines.
- algo_trader 4y ago> I want to see a "solar dispenser" that can drive very slowly across open land We gotta you covered (ha! pun!) [1]. [1] https://5b.co/web/image/website/1/social_default_image https://5b.co/web/image/website/1/social_default_image
- helloguillecl 4y agoI’d want the same but to place them on top of unused rail tracks. This way we would have a solid base to have them installed and possibly a lot of land available. The machine would need to support different gaugages.
- grapeskin 4y agoPlace them on basically any commercially unusable and economically “worthless” space. Instead of mowing down forests to lay them 5 inches off the ground, put them on highway noise barriers, build ceilings over commercial walkways (Europe is full of these but without solar panels), spread them out and put them high over parks to provide shaded areas that allow for greenery to grow underneath, and so on. The way solar farms are built now, or at least what I’ve seen, is wasteful. Solar has a great advantage in that it can be built alongside virtually anything, but a lot is currently in cleared out areas that can’t be used for anything else.
- ben_w 4y agoI think you'll be pleased to learn about Flugplatz Brandenburg-Briest. I've been wondering for a decade or so, why building codes almost everywhere don't yet require the entire roof of new buildings (not counting ceiling windows) to be covered in PV?
- Denvercoder9 4y agoThe problem here is that big, concentrated solar farms are far cheaper to install per kWh generated.
- Brometheus 4y agoDeutsche Bahn (German Rails) is doing this right now with tracks in use
- londons_explore 4y agoCabling in a solar farm is also a big part of the costs. If inverters were designed to output higher voltages - eg. a direct-to-10 kV output, then cables could be far thinner and cheaper. 3 phase silicone cable thinner than your baby finger rated for 20kV at just 20 amps could be run along (and carry all the energy from) a length of panels over a kilometer long. Such a design generally isn't used today because you have to design for someone potentially breaking in and trying to use cable cutters on a wire - you aren't allowed to electrocute the thief! But higher voltage cables could be used with a metal 'detection shield' sitting at just 50 volts which can detect someone starting to cut a cable and de-energise everything.
- algo_trader 4y agoBut that means the 20kV runs through all the panels? Setting aside regulation and panel certification, is this really purely a safety issue? Also, is it possible to convert the panel string 1KV DC output to 20KV DC? Are you familiar with this area?
- londons_explore 4y agoCompletely possible, yes. The question is is it cheaper to do so, considering your silicon devices will be more expensive (specifically the diodes on the output stage), but you'll save tens of cents of copper in the wiring per panel. I haven't done enough research to say for sure, but I strongly suspect it's cheaper.
- foota 4y agoIs this true? I wouldn't have thought that safety would be required there, is the same true for something like a substation plant? Those have warning signs all over.
- ramraj07 4y agoSounds like it’s a fundamental safety issue not just geared towards thieves. Even workers can trip and break a wire!