5 ms·
It astounds me that more homes weren't wiped out from the Northridge earthquake. A lot of the housing stock in California in particular is like rotting toothpic
by asdff 5y ago
It astounds me that more homes weren't wiped out from the Northridge earthquake. A lot of the housing stock in California in particular is like rotting toothpicks on eroding sand for a foundation. At least the homes generally lack basements so they will only fall a few feet off the posts. This particular reddit users is a contractor that posts their typical finds from structural inspections. People are paying between 800k-5m for the homes featured, generally:
https://old.reddit.com/user/DMAS1638/submitted/ https://old.reddit.com/user/DMAS1638/submitted/
Where you see winters homes are generally even in worse shape. Basements are leaking and eroding your foundation. Roofs are leaking and rotting your studs. Poor insulation is costing you a lot more money than in California. Chances are your water mains and sewer situation, both from your parcel as well as the municipal lines on the street, are all approaching end of life. Right as climate change brings heavier rains and flooding that stresses infrastructure where there isn't money as it is to maintain it even for old climate projections.
- tristor 5y agoIt's a real concern of mine and it's driving me towards considering building a custom home, at this point it's almost cheaper to do, especially since much of the work I can do myself and already have the necessary skills and tools. It's really and truly absurd what people are being expected to pay in comparison to what they get... I feel like most of the houses in the US are actually unsafe to live in because they don't care in construction about efficiency, indoor air quality, or mitigating common environmental concerns in those areas like radon gas. The minimal building codes in the US are truly obscene, and yet these slapdash houses are now priced for 3-4x what they are actually "worth" given the inflation rate. I have a 5 page document of bullet points making simple asks/requirements for a new home build, and most of them are focused on safety, reliability, and efficiency, and none of them would be done by default by any builder in the US, most are required by law in Europe. It's kind of nuts.
- tfvlrue 5y agoWould you be willing to share some of these requirements? I share your views on construction in the US, so I'm curious about some specific examples.
- tristor 5y agoSure, this is non-exhaustive of course, but here's a few of the items on the list I personally think are very important. * Foundation footings set to bedrock and insulated above the freeze line * Exterior walls framed in 2x6 or 2x8 studs w/ a preference for non-bridging stud products like t-studs * Exterior continuous insulation * Kitchen range hood needs to be externally ventilated with proper make-up air system * Using an ERV (Energy Recovery Ventilator) with filtered intakes for doing fresh air distribution within the home * No use of plastic flooring products (e.g. linoleum, vinyl, carpet, LVP, LVT, et al) which off-gas and spread plasticizers within the indoor envelope * Consider use of alternative methods of framing vs stick framing, like using ICF (Insulated Concrete Forms) * Natural gas on-demand hot water heaters w/ electric instant hot systems close to tap for showers * Roof trusses and decking properly constructed to account for the weight of solar panels on the south-facing slope * Split electrical paneling for high voltage (230V+) and low voltage (120V) circuits * Post-meter paneling for breaking out to circuit panels w/ a space for setting up a transfer switch to support future grid-tied solar with battery backup * All electric appliances w/ the exception of on-demand water heater and sealed gas fireplace, this provides a pathway for higher energy efficiency / lower carbon emissions by using solar * All cabinet work should be hung using french cleats for durability * Exterior door frames should be installed fully to the studs (e.g. use 3-4" long screws) * Interior doors should be solid core * All interior walls should contain sound-rated insulation to reduce noise pollution and improve climate zoning * All interior walls should be boarded with sound-sealant and noise rated drywall-type products * Subfloors should be insulated and there should be sound/thermal insulation underlayment below the flooring * The final construction prior to drywall should be able to achieve a blower door test score of ACH50 1.5 or lower with the make-up air and flue vents closed. Not all of these things would be required by code currently in Europe, but they're all good ideas for durability, efficiency, or safety. This is obviously with the intent to use rooftop solar power as well. If I do build a custom house, it'll be built to the Passivhaus standard.
- tfvlrue 5y agoThanks, these are great. > * Exterior door frames should be installed fully to the studs (e.g. use 3-4" long screws) I'm almost scared to ask... how else would you install an exterior door?