5 ms·
And this is based on frequency correct? So frequency is direct component. Right, frequency and wavelength are inverses of each other. You can turn one into th
by CamperBob2 5y ago
And this is based on frequency correct? So frequency is direct component.
Right, frequency and wavelength are inverses of each other. You can turn one into the other by dividing the velocity by either, f=c/m or m=c/f. Of course c isn't really c, but depends on the transmission media.
Gain does not require amplification, the transmission gain of antenna is not based on it, nether is reception.
By default, power gain is what an RF engineer refers to when s/he talks about "gain." And that does require amplification. You can increase voltage or current through impedance transformation, but never both at once.
- SigmundA 5y agoBy default, power gain is what an RF engineer refers to when s/he talks about "gain." Really they never use that term with antennas without amplifiers? Seems like its all over the literature, again back to previous material: 3.1.3 The Power Gain of a Transmitting Antenna The power gain G(θ,ϕ) of a transmitting antenna is defined as the power transmitted per unit solid angle in direction (θ,ϕ) relative to an isotropic antenna, which has the same gain in all directions. Frequently, the value of G is expressed logarithmically in units of decibels (dB): (3.31) For any lossless antenna, energy conservation requires that the gain averaged over all directions be ⟨G⟩=1 (3.32) Consequently, all lossless antennas obey ∫sphereGdΩ=4π. (3.33) Different lossless antennas may radiate with different directional patterns, but they do not alter the total amount of power radiated. Consequently, the gain of a lossless antenna depends only on the angular distribution of radiation from that antenna. In general, an antenna having peak gain G0 must beam most of its power into a solid angle ΔΩ such that ΔΩ≈4π/G0 This motivates the definition of the beam solid angle ΩA ΩA≡4πG0. (3.34) Thus the higher the gain, the smaller the beam solid angle. Directional antenna direct more power to the receiver they do not add more power through amplification. You could also say they waste less power toward no receiver. Reciprocally it works for the receiving antenna as well and is again referred to as gain everywhere I have seen.
- CamperBob2 5y agoKey phrase: "relative to an isotropic antenna." They can call it power gain all they want, but it's still not power gain. The literature is full of imprecise language, and it sounds like that's an example. If an antenna exhibited power gain, you could build a perpetual motion machine with a pair of them. It's not power gain. Instead, it's just less power loss.
- SigmundA 5y agoPlease point me to precise language that describes antenna gain without using the word gain rather than making a vague declaration. You seem to be trying to pigeon hole the word gain to mean only electronics gain [1] while the word gain has various related meanings [2] and in the RF world antenna gain is precisely defined and does not involve amplification [3]. [1] https://en.wikipedia.org/wiki/Gain_(electronics) https://en.wikipedia.org/wiki/Gain_(electronics) [2] https://www.merriam-webster.com/dictionary/gain https://www.merriam-webster.com/dictionary/gain [3] https://en.wikipedia.org/wiki/Antenna_gain https://en.wikipedia.org/wiki/Antenna_gain
- CamperBob2 5y agoAntenna gain relative to an isotropic radiator is a thing. Absolute power gain from a passive antenna is not. There is no such term as electronics gain. I really don't know how to explain this any more clearly; we're probably talking past each other. In engineering, we don't use the M-W dictionary. Things have to be spelled out more precisely, such as (in this case) exactly what the reference is for a given gain figure. When you see the term 'dB' used in technical writing, it's only a unitless ratio, not a power level, unless explicitly associated with a reference power level. In typical RF discussions, you'll frequently hear 'dBm' or 'dBw' used to describe absolute power levels relative to one milliwatt or one watt, for instance. But the antenna people are more likely to use 'dB' by itself to refer to the gain of one antenna over another, or perhaps 'dBi' to refer to gain over a theoretical isotropic antenna. The latter quantity normally does exceed zero, but only by focusing the existing RF power, not by generating or amplifying it. A related term is ERP, or effective radiated power. Imagine connecting a 1-watt transmitter to the 70-meter dish at a Deep Space Network tracking station. The ERP will be over ten million watts, but it won't even cook your lunch. It's effective power, expressed relative to what you could deliver to a target antenna with an isotropic radiator. Not actual physical power, in the sense of work divided by time.