3 ms·
Since the title specified a resolution, I assumed a VGA CRT with a DB15 connector. (Not an MDA, CGA or EGA) I was all set to warn you kids about the dangers of
by mikewarot 5y ago
Since the title specified a resolution, I assumed a VGA CRT with a DB15 connector. (Not an MDA, CGA or EGA) I was all set to warn you kids about the dangers of CRTs, high voltage, Xrays, and of course the implosion if you break the neck of the tube... and instead got bad capacitors on LCD displays.
Regardless of what the safety standards say, you should always remove power, and short any capacitors with a screwdriver or freshly checked jumper lead, as bleeder resistors (and jumper leads) fail. LCD backlights with cold cathode fluorescents use quite a bit of voltage, so be careful, and good luck!
- jve 5y agoThanks. I appreciate when someone gives safety advices as they come in handy when starting to tinker electronics. When repairing dishwasher I had to disconnect a huge capacitor... well it looked like it. Knowing what you just wrote about capacitors, it gave me shrugs and I was VERY careful handling that piece of thing. Can you give any advice on what good fume extractor for soldering does and if hobbyist that does repairs now and then should care?
- h2odragon 5y agoSolder fumes aren't great for your lungs, but its not a severe health threat: you're not soldering that much. A fan blowing at you to keep smoke and fumes out of your face should be sufficient for up to a few hours a day of soldering. If others in the house complain about the smell, then work on venting outside harder.
- mikewarot 5y agoA fume extractor with an activated charcoal filter grabs up the organic solvents that were used as flux to help make a good solder connection, and keep them out of your lungs. They don't cost much, but if smoke goes in, and doesn't come out, its helping, even if it isn't perfect.
- hermitdev 5y agoI also immediately had flash-backs to opening up an old CRT 13" TV that was going flaky (the sort of flaky where sometimes percussive maintenance worked). Being an electrical engineering student at the time, I thought I could handle it. I knew about the high voltage, I knew about the retained charged of the capacitors, etc, etc. What I wasn't prepared for was just how poorly shielded this thing was once I got it opened. I shocked myself almost immediately as I was doing basic examination. I hadn't even gotten to probing for shorts or broken connections. Thankfully, the shock wasn't bad, more startling than anything (I remember it being somewhat like brushing up against an electric fence). I was wearing a grounding strap on the arm of the hand where I got shocked. Not sure how much/if that helped any. That was enough for me to determine I wasn't qualified to work on it. I reattached the case and lived with its flakiness for a few years longer until it was replaced with an LCD.
- scrumper 5y ago> short any capacitors with a screwdriver Not universally a good idea to do that, especially not in a power supply. Safe enough in some circumstances but not all. Better to buy a discharge probe or make one by soldering a 2200 ohm 5w resistor between a couple of insulated wires. EDIT: made it less condescending.
- mikewarot 5y agoThings can fail open, a screwdriver can't. What's wrong with putting a dead short once across a capacitor? I've been doing it for 40 years in the interest of safety. Usually the bleeders are done and nothing happens anyway.
- scrumper 5y agoNothing, as long as it's a low voltage capacitor. Do it to a filter cap in a power supply and you'll have a huge spark and probably damage your screwdriver. Best practice if you're working with large capacitors is to discharge it (safely, using the tool I described), and confirm it worked using a voltmeter. I learned dealing with 600V monster filter capacitors in vacuum tube power supplies, they'll happily vaporize a screwdriver and knock you off your feet in the process.