4 ms·
My school had a way to keep peripherals from wandering off, but if all you need to do is swap the cables then I’m not sure that would still work. Wrapping the c
by hinkley 5y ago
My school had a way to keep peripherals from wandering off, but if all you need to do is swap the cables then I’m not sure that would still work. Wrapping the cables into a wiring loom makes that process slower, assuming the loom is complicated enough. Did you ever use heat shrink? Or locking cable ties?
What the school did was run a steel cable behind the desks, then put a loop of the mouse chord through a steel washer and ran the security cable through all the loops. If you secure both ends you can’t get the cables separated even with slack.
The trick is that the hole in the washer had to be smaller than the connector so you couldn’t fish it back through no matter how much slack you get. That could still work for USB-A, but these days the connectors are getting smaller than the diameter of curvature of the cable, so you’d break it trying to do this. And on many peripherals you could destroy the chord without reducing the value of the device. One could cut the cable and install this Trojan one on many devices these days, the only telltale would be that the cable isn’t routed properly, which might be harder to notice immediately.
- hughrr 5y agoAll the cables were terminated inside the box and strapped every 1 inch with cable ties. Nothing was exposed that could be disconnected other than the monitor IEC lead.
- lrvick 5y agoOn most keyboards and mice the cables are not soldered on the inside but just a quick connector. You can get a female/male versions of this connector placed on either side of an attiny85 for a quick solderless implant no one will ever see. Then just undo 2 screws, plug your implant inside the mouse/keyboard, screw it back. To make this harder intentionally strip the screws with a drill, understanding you will never be able to repair that unit again.
- IIsi50MHz 5y agoSeems there are special drill bits for removing stripped screws…
- a1369209993 5y ago> To make this harder Or, y'know, open it up and solder the connecter together (or remove the connector and solder the cable wires directly).
- hinkley 5y agoMy anecdote was a bit old and I’m certain some of those devices had soldered cables, meaning that a sheared wire couldn’t be handled by buying a new chord or combining parts of two mice. Because I specifically looked for that a few times with no luck. But they’re right, these days when you crack open things you often find a connector soldered to the motherboard and the cable is merely plugged in. I think it’s just easier to manufacture. Pick and place, bulk solder and then a machine to plug in the cable, fast as you like, maybe with a loop in it as a poor man’s strain protector.
- a1369209993 5y ago> meaning that a sheared wire couldn't be handled by [...] combining parts of two mice. Well, if you're stealing them, you only need parts from one mouse: cut the cable close to the mouse, untangle it from whatever crap it's locked to, take mouse and cable home with you, disassemble mouse, feed cable back though (I think it's called) grommet, strip cable, pick out wires, solder wires to approriate mouse internals, reassemble mouse, done. You have a working mouse with only slightly shorter cable than before. The point of using soldered cables for security is that setting up a soldering iron near a computer is conspicuous, so you get caught if try to install a attiny85 inside the mouse that way. You can still steal stuff just fine.
- victorhooi 5y agoWhen you say strip the screw - do you mean strip the screw head, by drilling out the head? That's evil... (Or do you know some way to strip the thread itself).
- lrvick 5y agoYeah just intentionally drill the head so those screws are not coming out again without power tools which should be obvious in the open where they are deployed. Or just epoxy the whole thing together.
- mhb 5y agoEpoxying the screws in might be easier?