4 ms·
Resistance and Voltage Dividers
- lmilcin 5y agoBe careful, reader, there are errors in the article. For example one egregious erorr is here on https://demofox2.files.wordpress.com/2021/06/image-34.png https://demofox2.files.wordpress.com/2021/06/image-34.png along with the surrounding text which consequently repeats the same error. The voltage divider is no magic, it can't create 12V of potential from 9V source. It would be more correct to replace -6V with 0V, then it would make sense.
- geocrasher 5y agoThe author clearly states immediately after that image: Note in the above, I’m not saying that is -6V and +6V, which would be 12 volts total, I’m just labeling the positive and negative sides of the 6 volts of power available. Context matters! See image: https://i.imgur.com/3fIZFFe.png https://i.imgur.com/3fIZFFe.png
- kazinator 5y agoThe diagram is bad; the context is worse. Firstly, "volts of power" even by itself is very, very poor language in an EE topic, never mind "positive and negative sides of 6V of power". By labeling two nodes of a circuit as -6V and +6V, you are showing that that's what the voltages are at those points (relative to some common reference) and thus the potential difference between them is 12V. That's the standard interpretation when you put a number next to a node of the circuit, and put a V suffix on it. What the diagram is communicating, to someone who can read circuits, is that R2 is dropping 12V, on a DC supply of 9V. The diagram is also neglecting to show some ground reference that is understandable as 0V, to indicate relative to what are those other voltages being referenced. By convention, the default place for that would be the - terminal of the battery. So the bottom of R2 would be shown as 0V, and the middle of the voltage divider, top of R2, as 6V (which matches what is already notated). It may be that the -6V is supposed to be referenced from the top of the R2 resistor, but this is confusing and inconsistent; all voltages for the same circuit should use the same reference. If you want to show that the bottom of R2 is down 6V from the top, you can label those nodes of the circuit, like R2a and R2b, and then write a formula: R2b - R2a = -6V which shows that R2b is -6V down from R2a.
- lmilcin 5y agoThe context just suggests the author has no idea what they are doing. That's not how any electronics engineer would label schematic and it is clearly wrong way to do it. Typically there is voltage reference selected and marked somewhere on the schematic. By tradition, if you don't mark it, it defaults to negative battery terminal. The rest of voltages would be understood in comparison to the reference point. More complex circuits might need multiple reference points. For example, a PSU converting from 230V AC to 12V DC will need at least two reference points.
- bjt2n3904 5y agoI... this article is a bit funny. I think it's extremely unhelpful to talk about a resistor divider as being a power supply, even though the author later shows how this fails in practice. Voltage, current, and power are difficult enough concepts for newcomers. It is commonly asked, "Can I use a voltage divider to power a circuit?" The answer is usually no, unless said circuit takes far less than 1 mA.
- kazinator 5y agoAn time you use a linear-regulator, such as a crusty 7805 voltage, you are using a voltage divider to power the circuit. It is an active voltage divider that adjusts its characteristics to keep the voltage constant, but a divider it is nevertheless. The high side transistors inside it are simply dropping the input voltage to bring it to the 5V level, and dissipating the V x I product as heat.
- GloriousKoji 5y agoThis is a terrible article. All that text, pictures and diagrams to poorly illustrated Kirchhoff’s Voltage Law, which wasn't even mentioned at all. The conclusion of 150ohms of internal resistance for a 9V battery is totally off too, doesn't help he's using resistors with 5% accuracy.
- carapace 5y agoSeems like a great place to trot out one of my favorite bits of electronic lore. The inverse of resistance (1/R) is called conductance and its unit is the Mho (No really!) When you calculate the resistance of resistors in parallel you're converting the Ohms to Mhos, adding them together, then converting back to Ohms. - - - - Oh, it seems I'm a little dated: "electrical conductance is measured in siemens (S) (formerly called "mho"s and then represented by ℧)." Oh well. ~ https://en.wikipedia.org/wiki/Electrical_conductance https://en.wikipedia.org/wiki/Electrical_conductance
- exmadscientist 5y agoI don't know why they had to get rid of the mho. It's a fun unit! And far less easy to confuse with the second (s) than the siemens (S). Many, many, many people write "mS" when they mean "ms". Normally this isn't indicative of a major character flaw or anything, but when you're in an interview, describe yourself repeatedly as "detail-oriented", and also make that mistake repeatedly... your "detail-oriented" interviewers will notice.
- stavros 5y agoOh man, is this one of those units that makes way more sense almost everywhere, like 2π for the diameter instead of the radius? Am I going to start noticing that "this equation would have been much easier using the conductance" now?