8 ms·

I understand that more load reduces frequency and less load raises frequency. Maybe something got lost in translation and "specific, constant RPM" was describi

I understand that more load reduces frequency and less load raises frequency. Maybe something got lost in translation and "specific, constant RPM" was describing (a feedback loop of) "watch the frequency and keep it steady" as opposed to "always use this value"? -- Also, wow. Seriously, wow. A locomotive running flat out could power several hundred homes. Transportation is expensive, both from a relative cost perspective, and also from a resource(-wastefulness) perspective. Electric (specifically grid-connected) trains also suddenly make a bit more sense.

petertodd 6y ago
> Transportation is expensive, both from a relative cost perspective, and also from a resource(-wastefulness) perspective. It really isn't. That locomotive running flat out may use a lot of energy. But it's also moving an enormous amount of freight, making the energy used per unit mass fairly small. For instance, CSX estimates it can move about 1 ton of freight 492 miles per gallon of diesel: https://www.csx.com/index.cfm/about-us/the-csx-advantage/fuel-efficiency/ https://www.csx.com/index.cfm/about-us/the-csx-advantage/fue... Your trip to the store and back will probably use more energy.
- dredmorbius 6y ago
  Running rail relatively slowly and on the level is low-power. Put hills or other load factors (start/stop, speed up / slow down, even wind) into the mix and it can go up. Elevation most especially --- railroads will go up to a thousand kilometers out of a straight-line route to avoid elevation gains. A passenger car should get 20-30 miles (30-50 km) per gallon, so unless your store run is several towns over (or you're in the sticks), probably less energy moving a ton 500 miles by rail. Though yes, personal autos are, relative to size and cargo capacity, profligate energy users.
  - sudosysgen 6y ago
    What goes up must go down. Every joule you have to put in to climb, you get back in the downhill. So in the end it mostly works out.
    - greenshackle2 6y ago
      I think you are forgetting brakes. There is absolutely no way a train is free-rolling it down a hill. They will be on brakes the entire time - dynos and air brakes - so you are "getting back" a lot of those joules in the form of electricity and heat, not momentum.
      - sudosysgen 6y ago
        Certainly. If this is a significant cost, then regenerative braking is installed. But it is mostly négligeable.
        dredmorbius 6y ago
        How large a battery are you planning on carrying?
        sudosysgen 6y ago
        None at all. Simply supply it to the grid. It would be perfectly predictable amounts of energy at predictable times, too. Some high speed passenger trains do actually do this, FYI.
        Ichthypresbyter 6y ago
        Although you can only supply the energy to the grid if your locomotive is connected to the grid while running, which diesels aren't.
        sudosysgen 6y ago
        Indeed, they aren't, because it's not economically worth it, because the energy is mostly too small to bother. Which is my entire point.
        LargoLasskhyfv 6y ago
        Not only them. Almost all newer EMU's for regional/commuting here do it, too. And I don't like it because I can hear the fucking chirping of the electronics when they do that. Which is *very annoying' when I have to ride them. Started around 20 years ago.
rebuilder 6y ago
Well, my hybrid electric car gets, on a summer day, about 70 km per 10 kWh charge. So if the locomotive can produce about 24000 kWh in a day, it could power 2400 35 km round-trip commutes. Now a freight train will run at, I don't know, 120 km/h? So, theoretically, it could run 2 880 km in a day. As we can see, that's a lot less than the combined 168 000 km 2400 hybrid cars could drive. So if we're comparing a train pulled by a locomotive like this to single-occupant hybrid electric cars, the train would have to transport 60 people to be about equivalent in efficiency. That seems very doable, you could fit that in a single train car. Also the 1000 kW power output is the peak output, I can't imagine a locomotive would be anywhere near it's max power very often. Did I goof in my calculations? I may well have! But based on these numbers, trains seem pretty efficient.
- reasonabl_human 6y ago
  Freight train implies cargo transport, while you’re generally correct from my point of view, I think the more apt comparison would be freight train vs. semi Also, looks like your car gets ~230Wh / mile, that’s pretty efficient compared to teslas, what kind of EV do you have? Are teslas just that inefficient or are you including ICE hybrid engine use in that measurement? Model 3 gets ~315 - 350 Wh / mile
  - rebuilder 6y ago
    It's an Opel Ampera, i.e. a Chevy Volt. That range, fully electric, is the best I've reliably gotten out of it, attainable on summer days (no heating!) driving on slower country roads. Highways and wintertime are a different story - this time of year I get maybe 45 km per charge. And currently it won't even run on battery only since it's so cold the car insists on intermittently running the engine for heat.
machello13 6y ago
Where do you think electric trains get their electricity from?
- LargoLasskhyfv 6y ago
  From the skies! The overhead wires are antennas sucking it out of the air.
Spooky23 6y ago
If you really want to have your mind blown, consider that one locomotive can move the equivalent of 400 trucks, and can be run in tandem to move more. Trains are similar to solar panels... they are operationally super efficient but require a large capital investment. Where they work, they are magic. Electric infrastructure is even more capital intensive, i would guess that if using was even marginally more efficient, it would have been implemented as railroads benefit from that efficiency. Equipment exists to accept grid power in diesel (Amtrak trains pulling into Penn station in NYC switch).
- Symbiote 6y ago
  I think the main motivations for electrifying a railway are: - flexibility and independence of power source. Switzerland can use hydropower, France can use nuclear power, many places could use coal power and not worry about losing rail transport in an oil shortage. - reduced maintenance costs (no diesel engines; reduced weight of the trains causes less wear on the track) - more power, i.e. faster trains, increasing the capacity of the railway line. Passengers approve, and freight trains can accelerate better meaning it's easier to run them between passenger trains. The US and Canada have less to gain with these than many other countries.
johnwalkr 6y ago
I used to work in the freight railroad industry. One instructive thing to demonstrate how efficient rails are, which I got to try once or twice: one person can move a fully loaded railcar with a pinch bar (basically a crowbar with an extra lever element) behind a wheel.
shsbsi 6y ago
“ Electric (specifically grid-connected) trains also suddenly make a bit more sense.” On a first glance it would appear so, but it a terrible idea in practice. At least for freight. Commuter trains are often electric (15 Hz? I forget), mostly for local air quality problems. Train engines are incredibly efficient. Only the largest marine engines are better. These engines are large enough that they approach the thermal efficiency of the thermal plant producing electricity. So no real gains for CO2 emissions. (Wind and solar don’t count at a first approx. since we’re talking about marginal E use. The train not connected on to the grid frees up production at a thermal plant to lower its production) But you also loose a lot of resiliency. In extremis, a diesel Trains don’t need anything to run. In case of an ice storm you have to rebuild big infrastructure. Train can help you transport that if they’re independent.
- amluto 6y ago
  Electric commuter trains have other major benefits. They stop and start frequently, and electric train sets can accelerate and decelerate faster than diesel. On the upcoming electric Caltrain, this will save quite a bit of time for long commutes. I believe that many electric trains can also regenerative brake. They can operate safely in long tunnels, unlike diesel. I suspect that diesel locomotives are considerably less efficient under the varying load conditions of a commuter train than they are for long freight routes. And, as far as I know, all major high speed trains are electric.
  - donarb 6y ago
    > electric train sets can accelerate and decelerate faster than diesel All locomotives use electric motors for traction. Diesel locomotives have a motor that turns a generator to produce electricity for the traction motors on the wheels. A diesel locomotive can stop and start just as fast as a fully electric locomotive, but commuter trains are relatively lighter than freight trains. Diesel locomotives can also use regenerative braking.
    - amluto 6y ago
      > A diesel locomotive can stop and start just as fast as a fully electric locomotive, The Caltrain electrification plan respectfully disagrees. I am not remotely an expert, but I would guess there are two major factors at play. First, a lot of commuter electric trains are multiple units and have no locomotive. This means that more of the wheels can supply traction, which presumably increases the traction-to-weight ratio of the whole train set. Secondly, I think that efficient diesel generators tend to be most efficient at a specific output power, whereas a commuter train runs over a wide range of output powers. A grid-powered electric train set can briefly draw several MW from the grid without a major loss of efficiency.
cgh 6y ago
> Also, wow. Seriously, wow. A locomotive running flat out could power several hundred homes. That's exactly what happened in my hometown, which generated power via a locomotive that was literally up on blocks. You could hear it grinding away from quite a distance. They only got connected to the grid when I was in my 20s and long gone.

petertodd 6y ago

> Transportation is expensive, both from a relative cost perspective, and also from a resource(-wastefulness) perspective. It really isn't. That locomotive running flat out may use a lot of energy. But it's also moving an enormous amount of freight, making the energy used per unit mass fairly small. For instance, CSX estimates it can move about 1 ton of freight 492 miles per gallon of diesel: https://www.csx.com/index.cfm/about-us/the-csx-advantage/fuel-efficiency/ https://www.csx.com/index.cfm/about-us/the-csx-advantage/fue... Your trip to the store and back will probably use more energy.

dredmorbius 6y ago
Running rail relatively slowly and on the level is low-power. Put hills or other load factors (start/stop, speed up / slow down, even wind) into the mix and it can go up. Elevation most especially --- railroads will go up to a thousand kilometers out of a straight-line route to avoid elevation gains. A passenger car should get 20-30 miles (30-50 km) per gallon, so unless your store run is several towns over (or you're in the sticks), probably less energy moving a ton 500 miles by rail. Though yes, personal autos are, relative to size and cargo capacity, profligate energy users.
- sudosysgen 6y ago
  What goes up must go down. Every joule you have to put in to climb, you get back in the downhill. So in the end it mostly works out.
  - greenshackle2 6y ago
    I think you are forgetting brakes. There is absolutely no way a train is free-rolling it down a hill. They will be on brakes the entire time - dynos and air brakes - so you are "getting back" a lot of those joules in the form of electricity and heat, not momentum.
    - sudosysgen 6y ago
      Certainly. If this is a significant cost, then regenerative braking is installed. But it is mostly négligeable.
      - dredmorbius 6y ago
        How large a battery are you planning on carrying?
        sudosysgen 6y ago
        None at all. Simply supply it to the grid. It would be perfectly predictable amounts of energy at predictable times, too. Some high speed passenger trains do actually do this, FYI.
        Ichthypresbyter 6y ago
        Although you can only supply the energy to the grid if your locomotive is connected to the grid while running, which diesels aren't.
        sudosysgen 6y ago
        Indeed, they aren't, because it's not economically worth it, because the energy is mostly too small to bother. Which is my entire point.
        LargoLasskhyfv 6y ago
        Not only them. Almost all newer EMU's for regional/commuting here do it, too. And I don't like it because I can hear the fucking chirping of the electronics when they do that. Which is *very annoying' when I have to ride them. Started around 20 years ago.

rebuilder 6y ago

Well, my hybrid electric car gets, on a summer day, about 70 km per 10 kWh charge. So if the locomotive can produce about 24000 kWh in a day, it could power 2400 35 km round-trip commutes. Now a freight train will run at, I don't know, 120 km/h? So, theoretically, it could run 2 880 km in a day. As we can see, that's a lot less than the combined 168 000 km 2400 hybrid cars could drive. So if we're comparing a train pulled by a locomotive like this to single-occupant hybrid electric cars, the train would have to transport 60 people to be about equivalent in efficiency. That seems very doable, you could fit that in a single train car. Also the 1000 kW power output is the peak output, I can't imagine a locomotive would be anywhere near it's max power very often. Did I goof in my calculations? I may well have! But based on these numbers, trains seem pretty efficient.

reasonabl_human 6y ago
Freight train implies cargo transport, while you’re generally correct from my point of view, I think the more apt comparison would be freight train vs. semi Also, looks like your car gets ~230Wh / mile, that’s pretty efficient compared to teslas, what kind of EV do you have? Are teslas just that inefficient or are you including ICE hybrid engine use in that measurement? Model 3 gets ~315 - 350 Wh / mile
- rebuilder 6y ago
  It's an Opel Ampera, i.e. a Chevy Volt. That range, fully electric, is the best I've reliably gotten out of it, attainable on summer days (no heating!) driving on slower country roads. Highways and wintertime are a different story - this time of year I get maybe 45 km per charge. And currently it won't even run on battery only since it's so cold the car insists on intermittently running the engine for heat.

machello13 6y ago

Where do you think electric trains get their electricity from?

LargoLasskhyfv 6y ago
From the skies! The overhead wires are antennas sucking it out of the air.

Spooky23 6y ago

If you really want to have your mind blown, consider that one locomotive can move the equivalent of 400 trucks, and can be run in tandem to move more. Trains are similar to solar panels... they are operationally super efficient but require a large capital investment. Where they work, they are magic. Electric infrastructure is even more capital intensive, i would guess that if using was even marginally more efficient, it would have been implemented as railroads benefit from that efficiency. Equipment exists to accept grid power in diesel (Amtrak trains pulling into Penn station in NYC switch).

Symbiote 6y ago
I think the main motivations for electrifying a railway are: - flexibility and independence of power source. Switzerland can use hydropower, France can use nuclear power, many places could use coal power and not worry about losing rail transport in an oil shortage. - reduced maintenance costs (no diesel engines; reduced weight of the trains causes less wear on the track) - more power, i.e. faster trains, increasing the capacity of the railway line. Passengers approve, and freight trains can accelerate better meaning it's easier to run them between passenger trains. The US and Canada have less to gain with these than many other countries.

johnwalkr 6y ago

I used to work in the freight railroad industry. One instructive thing to demonstrate how efficient rails are, which I got to try once or twice: one person can move a fully loaded railcar with a pinch bar (basically a crowbar with an extra lever element) behind a wheel.

shsbsi 6y ago

“ Electric (specifically grid-connected) trains also suddenly make a bit more sense.” On a first glance it would appear so, but it a terrible idea in practice. At least for freight. Commuter trains are often electric (15 Hz? I forget), mostly for local air quality problems. Train engines are incredibly efficient. Only the largest marine engines are better. These engines are large enough that they approach the thermal efficiency of the thermal plant producing electricity. So no real gains for CO2 emissions. (Wind and solar don’t count at a first approx. since we’re talking about marginal E use. The train not connected on to the grid frees up production at a thermal plant to lower its production) But you also loose a lot of resiliency. In extremis, a diesel Trains don’t need anything to run. In case of an ice storm you have to rebuild big infrastructure. Train can help you transport that if they’re independent.

amluto 6y ago
Electric commuter trains have other major benefits. They stop and start frequently, and electric train sets can accelerate and decelerate faster than diesel. On the upcoming electric Caltrain, this will save quite a bit of time for long commutes. I believe that many electric trains can also regenerative brake. They can operate safely in long tunnels, unlike diesel. I suspect that diesel locomotives are considerably less efficient under the varying load conditions of a commuter train than they are for long freight routes. And, as far as I know, all major high speed trains are electric.
- donarb 6y ago
  > electric train sets can accelerate and decelerate faster than diesel All locomotives use electric motors for traction. Diesel locomotives have a motor that turns a generator to produce electricity for the traction motors on the wheels. A diesel locomotive can stop and start just as fast as a fully electric locomotive, but commuter trains are relatively lighter than freight trains. Diesel locomotives can also use regenerative braking.
  - amluto 6y ago
    > A diesel locomotive can stop and start just as fast as a fully electric locomotive, The Caltrain electrification plan respectfully disagrees. I am not remotely an expert, but I would guess there are two major factors at play. First, a lot of commuter electric trains are multiple units and have no locomotive. This means that more of the wheels can supply traction, which presumably increases the traction-to-weight ratio of the whole train set. Secondly, I think that efficient diesel generators tend to be most efficient at a specific output power, whereas a commuter train runs over a wide range of output powers. A grid-powered electric train set can briefly draw several MW from the grid without a major loss of efficiency.

cgh 6y ago

> Also, wow. Seriously, wow. A locomotive running flat out could power several hundred homes. That's exactly what happened in my hometown, which generated power via a locomotive that was literally up on blocks. You could hear it grinding away from quite a distance. They only got connected to the grid when I was in my 20s and long gone.