5 ms·
For typical routing purposes, 10G is overkill. The number of people with faster than 1G internet is extremely small. Business customers who have >1G commercia
by PragmaticPulp 6y ago
For typical routing purposes, 10G is overkill.
The number of people with faster than 1G internet is extremely small.
Business customers who have >1G commercial connections are not in the market for using ODROID boards for their routing needs.
2.5G is perfect for hobbyist use because it is significantly cheaper than anything 10G at the moment, while being faster than common 1G.
If you need 10G switching, get a 10G switch.
- q3k 6y agoI don't want to build a switch/router on this.
- PragmaticPulp 6y agoThe parent board has a generic PCIe slot. You can add whatever card you'd like with appropriate adapters, including a 10G SFP+ card.
- q3k 6y agoIf by 'generic PCIe slot' you mean an NVMe slot that I have to buy janky adapters for, and figure out mechanical mounting for, then yeah. But I'm not sure I'd like to depend on that. And then I might as well do that with an Intel NUC, or just go for a normal mini-ITX motherboard.
- stingraycharles 6y agoMost of the time 10G routing isn’t for WAN but instead for the LAN.
- PragmaticPulp 6y agoI think everyone is missing the point of this cheap hobbyist board. The PCIe slot on the H2 is PCIe 2.0 x4, which doesn't have enough bandwidth to saturate more than one 10G port. This is why hobby hardware and the enthusiast market is so difficult: You can make a great product at a cheap price point and people will still complain that it doesn't satisfy their high-end niche edge case.
- Plutoberth 6y agoThis board has four 2.5G ports, not four 10G ports, so the 16G bandwidth for four PCie 2.0 lanes is more than enough.
- mlyle 6y agoRight... the parent is saying that 4x10G is pointless compared to 4x2.5G, because PCIe 4 lanes will top out at forwarding around 7gbps of traffic. You can't do line rate on all ports either (limited by PCIe alone, let alone CPU for smaller packets), but you can certainly fill an individual port, which I suspect is the goal.
- q3k 6y ago> because PCIe 4 lanes will top out at forwarding around 7gbps of traffic [...] limited by PCIe alone Are you sure about that? With 5GT/s (or 500MB/s) per lane, and with 4 lanes, that should be plenty, no? Intel adapters like the x520-DA2 are specced at 2x 10G, and use PCIe 2.0 x8. FWIW, I was also able to iperf3 around 3.7Gbps on a X520-DA2 connected to an RPi4's single-lane PCIe 2.0.
- mlyle 6y ago> FWIW, I was also able to iperf3 around 3.7Gbps on a X520-DA2 connected to an RPi4's single-lane PCIe 2.0. Yah, I said forwarding-- so each packet goes over the PCIe link twice. So, to use your test-- 3.7 x 4 / 2 = 7.4gbps. I said around 7. 7.4gbps would be a bit more than I'd expect, but I'd not be shocked.
- q3k 6y agoBut PCIe is full duplex! With PCIe 2.0 x4 there's 4 lanes in each direction [1], so when 'forwarding' over a single 10G link you can expect to send and receive simultaneously at the speed I mentioned earlier. [1] - https://en.wikipedia.org/wiki/PCI_Express#Pinout https://en.wikipedia.org/wiki/PCI_Express#Pinout
- mciancia 6y ago> 2.5G is perfect for hobbyist use because it is significantly cheaper than anything 10G at the moment No, not really, it's the other way around. SFP+ based 10g networking equipment is much cheaper and and with much higher availability. And if needed, you can always adapt it to 1/2.5/5.10g networking using sfp+->rj45 transceivers. Only disadvantage was that you had to run fiber. Maybe it will change this year, bot for now 10g was a way to go