6 ms·
Yeah, but those Linux SoCs don't have a ADC or accurate PWM timers. You cam probably beat an ATMega with a STM32 of some kind. But the embedded world is more a
by dragontamer 6y ago
Yeah, but those Linux SoCs don't have a ADC or accurate PWM timers.
You cam probably beat an ATMega with a STM32 of some kind. But the embedded world is more about simplicity of connecting to ADC / PWM / I2C and other such functionality. But even vs STM, ATMega supports 5V and full static (0Hz clock) operation.
You're not looking at MHz or RAM when you buy a microcontroller. You're looking at connectivity (which STM delivers... but there's still an ATMega / Arduino legacy advantage from a code perspective).
----------
20 years ago, plenty of people were making fun of 8051 boards that cost $100 but provided only 12MHz of clock and 256-bytes of RAM (not kB, literally bytes). The PC-market / high-level programmers always underestimate the importance of connectivity and overemphasize specs.
Embedded is mostly fine with 20MHz clocks: and arguably prefers less power usage (so things like "static 0Hz operation" are big features). Having an ATMega run at 100kHz clock rates for maximum power-savings but still providing the functionality you need (ie: Timers / ADC / etc. etc.) is pretty useful.
Or ATMegas can accept unregulated 5V, and just running off of USB-power (which can be between 4.5V to 5.5V in practice, exceeding the specs of STM32 chips). That simplifies the design of your board, since you don't need a buck-converter to go from 5V unregulated USB to 3.3V on the STM32.
- kube-system 6y agoFor sure. I still prefer tinkering with my Arduino to my Raspberry Pi, because the electronics side of things is way easier.
- duskwuff 6y ago> You cam probably beat an ATMega with a STM32 of some kind. You can run Linux directly on some STM32 MCUs. No emulation required! https://github.com/torvalds/linux/tree/master/arch/arm/mach-stm32 https://github.com/torvalds/linux/tree/master/arch/arm/mach-... That being said, static operation is really less of an issue than you're implying. Modern MCUs can idle (not sleep!) at under a milliamp; it's not difficult to get them to draw less average current than the leakage current of their battery. The lack of 5V operation is a little annoying in some scenarios, but is easily worked around with a 3.3V LDO -- which is frequently required anyway for interoperability with other components. (A switching converter is hardly necessary for a USB device drawing a couple milliamps.)
- dragontamer 6y ago> it's not difficult to get them to draw less average current than the leakage current of their battery. Well... depends on the battery. A bog-standard AA Alkaline battery has 2500 mA-hr (from 1.5V to 1V, @100mA draw: https://data.energizer.com/pdfs/e91.pdf https://data.energizer.com/pdfs/e91.pdf), and have a ~3%/year self discharge rate. That's a leakage current of 75mA-hrs / year, or ~10 uA if I did my math correctly. Lithium, and watch button batteries (Silver) leak even less! ATTiny 1607 is specified at 6uA at 1.8V @ 32kHz active mode (though 5V barely is any more current). It looks like STM32G031J4 is ~20 uA at "low-power mode" @ 1.8V 32kHz (a special mode below 2MHz). Which is a lot better than I was expecting. (Note to others who may not know this: this is likely a Cortex-M0+ design only. Typical ARMs will not be able to reach this low level of power. Heck, larger STM32 Cortex-M4 processors probably have a much higher minimum clockrate) Both chips are ~200 uA at 2MHz, Which gets you to ~500 days of continuous operation from 2500 mA-hr AA. ------ Yeah, there's a bunch of batteries that self-discharge in just 3-months. But... alkaline AA exist for a reason! Low-self discharge, and they're actually really good at these milliamp/microamp levels of current. And again, its all about those silver-watch batteries or lithium-watch batteries if you really want the lowest self-discharge in the market. (~5 years per silver-watch battery, but you need to draw stupidly low amounts of current). It seems like the ATTiny 1607 still has a superior sleep mode compared to STM32G031J4, so if you're sleeping most of the time on a watch battery, maybe ATTiny wins. I do agree with you though: it does seem like STM32 has really dropped their power down a lot. I don't know if STM32 always supported 32kHz clock rates however, I seem to remember them having a higher minimum clock rate last time I checked this out. Lowering those clock speeds really helps at minimizing power. And I expect AA-batteries to be the typical size of most people's hobby projects. I dunno if "full static" is really needed, since 32kHz is still really, really low power. It seems nice that ATTiny / ATMegas hve 0Hz as an option (maybe if an external temporary clock turns on only occasionally in a power-constrained environment).
- magicalhippo 6y ago> The lack of 5V operation is a little annoying It should be noted many STM32's (if not all, huge family) have 5V tolerant I/O pins, so it's not nearly as annoying as it could be.
- SomeoneFromCA 6y agoYou should never run microcontroller from an unregulated supply - it will brown out. USB is not unregulated, it just has bad precision, but regulation I am sure is pretty fine.
- dragontamer 6y agohttps://trmm.net/AVR_RFID/ https://trmm.net/AVR_RFID/ Looks like a pretty unregulated power supply to me, lol. I realize you're talking about normal use, and not abuse like this avrTiny example, but... those Microchip / Atmel chips are pretty legendary with regards to the electrical abuse they withstand.